KitchenAid W10520792B manual Drain Pump Installation, Rear View, Kit Contains

Page 7

A

B

6.Remove and discard the short, black plastic tube from the end of the water line inlet.

7.Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet.

A.Bulb

B.Nut

3.Now you are ready to connect the copper tubing. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply.

Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A

B

C

A. Compression sleeve

C. Copper tubing

B. Compression nut

 

4.Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

IMPORTANT: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

5.Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown. Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

Rear View

A

B

C

A. Copper tubing

C. Inlet water tube clamp and

B. Water supply tube clamp

supply line connector

A

B

C

D

A. Line to ice maker

 

C. Ferrule (purchased)

B. Nut (purchased)

 

D. Supplied line from ice maker

8.Install the water supply tube clamp around the water supply line to reduce strain on the coupling.

9.Turn shutoff valve ON.

10.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Drain Pump Installation

(on some models)

NOTE: Connect drain pump to your drain in accordance with all state and local codes and ordinances. It may be desirable to insulate drain tube thoroughly up to drain inlet to minimize condensation on the drain tube. Insulated tube kit Part #W10365792 is available for purchase. Drain pump is designed to pump water to a maximum height of 10 ft (3 m). Use only Whirlpool approved drain pump kit Part Number 1901A. Do not connect the outlet end of the drain tube to a closed pipe system to keep drain water from backing up into the ice maker.

Kit Contains:

Drain pump kit Part Number 1901A

⁵⁄₈" ID x 5¹⁄₈" drain tube (ice maker bin to drain pump reservoir inlet)

¹⁄₂" ID x 10 ft (3 m) drain tube hose (drain pump discharge to household drain)

⁵⁄₁₆" ID x 32" (81 cm) vent tube (drain pump reservoir vent to ice maker cabinet back)

Cable clamps (secures vent tube to back of ice maker) (3)

#8-32 x ³⁄₈" pump mounting screws (secures drain pump to baseplate and clamps to back of ice maker) (5)

⁵⁄₈" small adjustable hose clamp (secures vent to drain pump)

⁷⁄₈" large adjustable hose clamp, (secures drain tube to ice maker bin and drain pump reservoir inlet) (3)

Rear panel (2)

Instruction sheet

7

Image 7
Contents Manual de uso y cuidado Use & Care GuideGuide d’utilisation et d’entretien Índice Table of ContentsTable DES Matières Installation Instructions ICE Maker SafetyTools and Parts Custom Panel Dimensions Location Requirements Unpack the Ice MakerConnect Water Supply Electrical RequirementsWater Supply Requirements Vacation or Extended Time Without UseRear View Drain Pump InstallationKit Contains Water Supply Line If Ice Maker Is Currently InstalledDrain Pump Installation Drain CapVent Tube Drain Pump Mounting Tab SlotSide View Connecting the DrainDrain Connection Gravity Drain SystemOption 2 With Hinge-Side Spacer Install Custom Overlay PanelDoor Reversal-Side Swing Only Option 1-Without Hinge-Side SpaceReplace Door Remove Stainless Steel Door Wrap Panel on some modelsDoor Stop and End-Cap Reversal Reverse HingesReverse Door Catch LevelingTop Hinge Bottom HingeWater Filtration System Install the Water FilterWater Filter Status Light ICE Maker USE Using the ControlsHow Your Ice Maker Works ICE Maker Care CleaningNormal Sounds Interior Components Condenser Dirty or Clogged CondenserVacation and Moving Care For Ice Makers with a Drain Pump InstalledTo Shut Down the Ice Maker Ice Maker Seems Noisy TroubleshootingIce Maker Operation Ice Maker Will Not OperateIce Quality Ice ProductionIce Maker Runs But Produces No Ice For further assistance If you need replacement partsU.S.A CanadaAffresh* Stainless Steel Cleaner Performance Data SheetAccessories CleanerThis limited warranty does not cover Kitchenaid ICE Maker WarrantyPage Instrucciones DE Instalación Seguridad DE LA Fábrica DE HieloHerramientas y piezas Dimensiones del panel hecho a la medida Requisitos de ubicación Desempaque la fábrica de hieloConexión del suministro de agua Requisitos eléctricosRequisitos del suministro de agua Vacaciones o tiempo prolongado sin usoEl juego contiene Instalación de la bomba de desagüeConexión de la tubería de agua Vista posteriorInstalación de la bomba de desagüe Si la fábrica de hielo ya está instaladaTapa de desagüe Línea de suministro de aguaBomba de desagüe instalada Tubo de desagüeRanura de la lengüeta de montaje de la bomba de desagüe Ubicaciones de las piezasVista lateral Conexión del desagüeTubo de ventilación Sistema de desagüe por gravedadSistema de la bomba de desagüe en algunos modelos Instale el panel de revestimiento hecho La medidaConexión del desagüe Llave de tuercas de ¹⁄₄ Destornillador Phillips Bisagra inferior Inversión de las bisagrasCómo volver a colocar la puerta Bisagra superiorInstalación del filtro de agua NivelaciónSistema de filtración de agua Cómo invertir el seguro de la puertaReemplazo del filtro de agua Luz de estado del filtro de aguaProceso de elaboración de hielo USO DE LA Fábrica DE HieloCómo funciona su fábrica de hielo Uso de los controlesSonidos normales Cuidado DE LA Fábrica DE HieloLimpieza Condensador Un condensador sucio u obstruido Tornillo Espaciador de plástico Rejilla de corte Componentes interioresPara apagar la fábrica de hielo Cuidado durante las vacaciones y mudanzasFuncionamiento de la fábrica de hielo Solución DE ProblemasLa fábrica de hielo no funciona Calidad del hielo Producción de hieloLa fábrica de hielo funciona pero no produce hielo Si necesita piezas de repuesto Problemas de plomeríaAyuda O Servicio Técnico En los EE.UULimpiador Hoja DE Datos DEL RendimientoAccesorios Filtro de aguaEsta garantía limitada no cubre Garantía DE LA Fábrica DE Hielo DE KitchenaidPage Sécurité DE LA Machine À Glaçons Instructions D’INSTALLATIONOutillage et pièces Dimensions du panneau personnalisé Nettoyage avant l’utilisation Exigences d’emplacementDéballage de la machine à glaçons Enlèvement des matériaux d’emballageRaccordement à la canalisation d’eau Spécifications électriquesSpécifications de l’alimentation en eau Vacances ou longue période d’inutilisationVue arrière Raccordement du tuyau d’eau Installation de la pompe de vidangeBouchon de vidange Si la machine à glaçons est installéeInstallation de la pompe de vidange Contenu de l’ensembleEncoche de patte de montage de la pompe de vidange Pompe de vidange installéeTube de vidange Position des piècesVue latérale Raccordement au drain de vidangeTube de ventilation Vidange par gravitéSystème avec pompe de vidange sur certains modèles Installation du panneau décoratif personnaliséRaccordement du drain de vidange Inoxydable Option 2-Avec cale despacement côté charnièreInversion du sens de montage des charnières Réinstallation de la porteRéinstallation du revêtement de porte sur certains modèles Inversion du sens dinstallation de la gâche de porteNivellement Installer le filtre à eauSystème de filtration d’eau Témoin lumineux du filtre à eau Remplacement du filtre à eauUtilisation DE LA Machine À Glaçons Fonctionnement de la machine à glaçonsSons normaux Utilisation des commandesMode Max Ice glaçons max Alarme de porte entrouverteSystème de la machine à glaçons Entretien DE LA Machine À GlaçonsNettoyage Surfaces extérieuresComposants intérieurs Arrêt de la machine à glaçons Précautions à prendre avant les vacances ou un déménagementMachine à glaçons avec pompe de vidange La machine à glaçons ne fonctionne pas DépannageProduction de glaçons Problèmes de plomberie Au Canada Assistance OU ServiceAccessoires Aux États-UnisSystème de filtration d’eau de la machine à glaçons Feuille DE Données SUR LA PerformanceLa présente garantie limitée ne couvre pas Garantie DE LA Machine À Glaçons KitchenaidW10520792B

W10520792B specifications

The KitchenAid W10520792B is an innovative component designed to elevate your culinary experience. This replacement part is particularly known for its reliability and efficiency, ensuring that your KitchenAid appliances function optimally. One of the main features of the W10520792B is its compatibility with various KitchenAid models, which makes it a versatile choice for users seeking to maintain their kitchen equipment in peak condition.

One notable characteristic of the W10520792B is its durable construction. Made from high-quality materials, it is designed to withstand the rigors of daily cooking tasks, providing longevity and consistent performance. This durability means that home chefs can rely on this part to perform under pressure, whether mixing, kneading, or whipping.

The W10520792B showcases KitchenAid's commitment to innovative design. The part utilizes advanced manufacturing techniques to ensure precision, which contributes to the overall efficiency of KitchenAid appliances. This attention to detail not only enhances the functionality of the equipment but also allows users to enjoy a more seamless cooking experience.

Another essential technology found within the W10520792B is its user-friendly installation process. Designed with the homeowner in mind, this component can typically be replaced without the need for professional assistance, saving both time and money. Clear instructional guidelines usually accompany the part, enabling even less experienced users to successfully complete the replacement with ease.

Moreover, the W10520792B is part of KitchenAid's commitment to sustainability. The materials used are often environmentally friendly, ensuring that customers can maintain their appliances while being conscious of their ecological footprint. This quality appeals to consumers who value both performance and environmental responsibility in their kitchen tools.

In summary, the KitchenAid W10520792B is an essential component that embodies quality, durability, and innovation. Its compatibility with various models, user-friendly installation, and sustainable materials make it an excellent choice for maintaining the high performance of KitchenAid appliances. Home cooks can rely on this part to enhance their cooking experience, allowing them to create delicious meals with confidence. Whether you are an aspiring chef or a seasoned culinary expert, the W10520792B is sure to play a pivotal role in your kitchen adventures.