Jenn-Air W10282143B manual Ice Maker Door, Remove Door, Hinge pin

Page 9

9.Pull the ice maker forward to access the top and sides of the door.

10.Remove the gaskets from the interior door panel and set aside.

11.Using the factory drilled holes as a guide, use a scribe and mark the drilling locations on the overlay panel.

12.Drill eight ¹⁄₈" x ¹⁄₂" (3.18 mm x 12.7 mm) deep holes into the overlay panel.

NOTE: Do not drill deeper than ¹⁄₂" (12.7 mm).

13.Use eight #8 x ¹⁄₂" pan-head wood screws to attach the panel to the door.

14.Attach a handle if necessary.

15.Replace the gaskets on the inner door panel.

16.Move the ice maker back into place under the counter.

Ice Maker Door

Tools needed:

Gather the required tools and parts before starting installation.

■

⁵⁄₁₆" wrench

■

Flat putty knife

■

¹⁄₄" wrench

■

Phillips screwdriver

Hinge pin

⁵⁄₁₆" Hex-head hinge screw

Option 1 - Without Hinge-Side Spacer

A

B

29³¹⁄₆₄"

(73.0 cm)

C

14³³⁄₆₄"

(36.9 cm)

A. #8 x ¹⁄₂" Pan-head wood screw

B. Adhesive pads

C. Custom panel

Option 2 - With Hinge-Side Spacer

A

B

29¹⁄₂"

(74.9 cm)

C

14⁵⁄₈"

(37.1 cm)

A. #8 x ¹⁄₂" Pan-head wood screw

B. Adhesive pads

C. Custom panel

Handle screw

End cap screw

Remove Door

1.Unplug ice maker or disconnect power.

2.Remove the handle screws and handle from the top of the door (on some models). Keep the parts together and set them aside.

3.Remove the hinge pin from the top hinge.

4.Remove the door from the hinges and screw the top hinge pin back into the top hinge.

5.Remove the door skin (on some models) as follows:

■Remove the two screws from the top and bottom of the door skin.

■Remove the skin and the edge covers from the door. Keep the parts together and set them aside.

6.Reverse the door end caps as follows:

■Remove the screw and end cap from the top corner. Move it diagonally to the opposite side's bottom corner, keeping the straight side of the end cap facing the front of the ice maker.

■Remove the screw and end cap from the bottom corner. Move it diagonally to the opposite side's top corner, keeping the straight side of the end cap facing the front of the ice maker.

AB CD

DC BA

A. Top corner open (no end cap)

B. Beginning top corner end cap

C. Beginning bottom corner end cap

D. Bottom corner open (no end cap)

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Manual DE USO Y Cuidado USE & Care GuideGuide D’UTILISATION ET D’ENTRETIEN W10282143BTable of Contents ÍndiceTable DES Matières Installation Instructions ICE Maker SafetyCustom Panel Dimensions Tools and PartsOption 2 With Hinge-Side Spacer Option 1 Without Hinge-Side SpacerFront of Panel Top of PanelLocation Requirements Unpack the Ice MakerWater Supply Requirements Electrical RequirementsLeveling Recommended grounding methodConnecting the Water Line Connect Water SupplyRear View Connecting the Drain Install Custom Overlay PanelDrain Connection Gravity Drain SystemRemove Door Ice Maker DoorHinge pin #8 x ¹⁄₂ Pan-head wood screw Adhesive pads Custom panelNormal Sounds Using the Controls ICE Maker USEHow Your Ice Maker Works ICE Maker Care CleaningExterior Surfaces Ice Maker SystemVacation and Moving Care Interior ComponentsTo shut down the ice maker For ice makers with a drain pump installed TroubleshootingIce Maker Operation Your ice maker will not operatePlumbing Problems Assistance or ServiceIce Production Ice QualityThree Year Limited Warranty Parts and Labor JENN-AIRICE Maker WarrantyItems Excluded from Warranty Disclaimer of Representations Outside of WarrantySeguridad DE LA Fábrica DE Hielo Dimensiones del panel hecho La medidaInstrucciones DE Instalación Herramientas y piezasOpción 2 Con el espaciador del lado de la bisagra Opción 1 Sin el espaciador del lado de la bisagraFrente del panel Parte superior del panelRequisitos de ubicación Desempaque la fábrica de hieloRequisitos del suministro de agua Requisitos eléctricosNivelación Método recomendado para la conexión a tierraConexión del suministro de agua Conexión de la tubería de aguaVista Posterior Sistema de desagüe por gravedad Conexión del desagüeSistema de la bomba de desagüe en algunos modelos Conexión del desagüeInstale el panel de revestimiento Hecho a la medida Puerta de la fábrica de hieloSaque la puerta Bisagra inferior Bisagra superiorInvertir las bisagras Volver a colocar la puertaSonidos normales USO DE LA Fábrica DE HieloCómo funciona su fábrica de hielo Proceso de elaboración de hieloCuidado DE LA Fábrica DE Hielo Uso de los controlesLimpieza Componentes interiores CondensadorUn condensador sucio u obstruido Tapa de la rejilla de corte TornillosCuidado durante las vacaciones y Mudanzas Para apagar la fábrica de hieloTornillo de mariposa Soporte de la pala para el hielo Solución DE Problemas Funcionamiento de la fábrica de hieloProducción de hielo Problemas de plomería Ayuda O Servicio TécnicoCalidad del hielo Exclusiones DE LA Garantía Garantía DE LA Fábrica DE Hielo JENN-AIREsta garantía limitada no cubre Exclusión DE Garantías ImplícitasExclusión DE Declaraciones Fuera DE LA Garantía Dimensions du panneau personnalisé Instructions D’INSTALLATIONSécurité DE LA Machine À Glaçons Outillage et piècesOption 2 Avec cale despacement côté charnière Option 1 Sans cale despacement côté charnièreAvant du panneau Partie supérieure du panneauDéballage de la machine à glaçons Exigences demplacementSpécifications électriques Méthode de mise à la terre recommandéeSpécifications de l’alimentation en eau NivellementRaccordement à la canalisation d’eau Raccordement du tuyau d’eauVUE Arrière Vidange par gravité Raccordement au drain de vidangeSystème avec pompe de vidange sur certains modèles Raccordement du drain de vidangePorte de la machine à glaçons Installation du panneau décoratif personnaliséDépose de la porte Axe de la charnièreInversion des charnières Réinstallation de la porteCharnière supérieure Charnière inférieureSons normaux Utilisation DE LA Machine GlaçonsFonctionnement de la machine Glaçons Fabrication de la glaceUtilisation des commandes Entretien DE LA Machine GlaçonsNettoyage Composants intérieurs CondenseurUn condenseur sale ou obstrué Bac à eau Vis à ailette du bac à eau Capuchon de vidangePrécautions à prendre avant les vacances ou un déménagement Arrêt de la machine à glaçonsVis à ailette Support de pelle à glace Production de glaçons DépannageLa machine à glaçons ne fonctionne pas La machine à glaçons semble bruyanteAssistance OU Service Qualité des glaçonsProblèmes de plomberie Garantie Limitée DE Trois ANS Pièces ET MAIN-D’ŒUVRE Garantie DE Machine À Glaçons JENN-AIRÉléments Exclus DE LA Garantie La présente garantie limitée ne couvre pas2011 All rights reserved W10282143B

W10282143B specifications

The Jenn-Air W10282143B is a high-performance appliance that exemplifies the brand's commitment to innovation and quality in kitchen technology. Designed to cater to the needs of modern culinary enthusiasts, this model integrates advanced features and functionalities that simplify meal preparation while enhancing cooking experiences.

One of the standout features of the Jenn-Air W10282143B is its high-efficiency cooling system. This system ensures that food items are stored at optimal temperatures, preserving freshness for an extended period. The unit is also equipped with adjustable shelving, allowing users to customize the interior layout to accommodate various food items, from large platters to delicate produce. This versatility is a significant advantage for households with diverse storage needs.

Technologically, the Jenn-Air W10282143B incorporates smart connectivity features. Through Wi-Fi integration, users can control the appliance remotely via a dedicated app. This means you can adjust settings, receive alerts, and even monitor energy usage from your smartphone. This level of control and convenience is ideal for busy individuals and families who are always on the go.

Another key characteristic of the Jenn-Air W10282143B is its sleek and modern design. The appliance features a stainless-steel exterior that not only enhances its aesthetic appeal but also provides superior durability and easy maintenance. Fingerprint-resistant finishes prevent smudges and keep the surface looking clean and polished, contributing to a tidy kitchen environment.

In terms of energy efficiency, the Jenn-Air W10282143B meets stringent industry standards. It is designed to consume less electricity compared to traditional models, making it an environmentally friendly choice that helps to reduce utility bills without compromising performance.

Safety features are paramount in this design. The model includes automatic shut-off capabilities and safety locks, providing peace of mind for households with children or pets. Furthermore, the intuitive control panel is user-friendly, allowing everyone in the household to operate the appliance with ease.

Overall, the Jenn-Air W10282143B is a perfect blend of style, functionality, and smart technology. With its user-centric design and commitment to performance, it stands out as a reliable kitchen companion for anyone looking to enhance their culinary journey. The combination of innovative features and an elegant aesthetic makes this model a valuable addition to any modern kitchen.
Top Page Image Contents