Bunn SNG0033000 manual Review RECIPES? No YES

Page 16

PROGRAMMING THE BREWER (cont.)

SET NEW RECIPES (cont.)

SET NEW RECIPE:

If not using a Smart Funnel (with a computer chip) and/or a G9-2T DBC or MHG Grinder, the brewer will function as a standard Bunn Single/Dual Brewer:

It is possible to operate the brewer without using a Smart Funnel and/or a G9-2T DBC or MHG Grinder. If a standard funnel, or if a non-DBC grinder is used the brewer will automatically select a NO NAME coffee when the BREW switch is pressed. This means that no name was read from the funnel's handle.

There is a NO NAME coffee program that can be set in the SINGLE brewer and two NO NAME coffee

REVIEW RECIPES?

NO YES

EXIT TO

 

 

 

 

 

 

 

 

NEXT FUNCTION

 

 

 

 

SCREEN

SINGLE

 

 

DUAL

 

 

 

 

BREWERS

 

BREWERS

NO-NAME

 

 

NO-NAME LEFT

MODIFY SHOW NEXT

 

MODIFY SHOW NEXT

programs that can be set in the DUAL brewer which are referred to as NO NAME LEFT and NO NAME RIGHT. The left and right sides of the brewer can be set up independently of each other. This includes BREW

VOLUMES, BYPASS PERCENTAGES, PULSE BREW TIMES, and DRIP-OUT TIMES. The brewer will perform in the same capacity as a standard Bunn Single/Dual Brewer.

(COFFEE NAME)

MODIFY SHOW NEXT

NO-NAME RIGHT MODIFY SHOW NEXT

The instructions for programming the NO NAME settings are on the following pages. The same steps are followed for setting the recipe as those that are used to MODIFY A RECIPE, beginning on page 21.

Note that on SINGLE brewers, when the display reads NO NAME, that is when MODIFY should be pressed in order to set the parameters for the NO NAME coffee.

On DUAL brewers, when the display reads NO NAME LEFT, that is when MODIFY should be pressed in order to set the parameters for the NO NAME LEFT coffee. Otherwise, press NEXT to display NO NAME RIGHT. At this point, MODIFY should be pressed in order to set the parameters for the NO NAME RIGHT coffee.

NOTE: Before beginning setup, insert funnel(s) into the funnel rails (both sides on DUAL brewers), and place a Soft Heat Server(s) beneath the funnel(s).

BREW OZ. XX.X (-) DONE (+)

Page 16

41341 080108

 

Image 16
Contents Dual SH DBC BUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Switches ProgrammingProgramming Lockout Switch mounted on main control board ScreenOutputs Main ScreenUsing a Smart Funnel and a G9-2T DBC or MHG Grinder Not using a Smart Funnel and/or a G9-2T DBC or MHG GrinderRecipe Programing Methods RecipesLevel Continue toProgram Flow Diagram Program Flow Diagram Units Setting Units of Measure Procedure for modifying units of measureEnable Energysavr NEW Recipe ?Procedure for Setting the Recipe SET NEW RecipeSET NEW Recipe Sizes DONE?Procedure to program the coffee name SET NEW RecipesReview RECIPES? No YES Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee Favors Procedure for reviewing recipesReview Recipes WAS the Last RecipeBrew OZ Setting or Adjusting Brew VOL- Umes Batches DONE? No YESBypass SET Pulse Brew Modifying pulse brewSET Pulse Brew SET Pulse Brew Easy Pulse Setup TIMES? SET Pulse Brew Enter TimesDONE? SET Preinfusion Batches DONE?Setup Complete Procedure to modify drip timesDrip Time now displayed on non funnel lock units as well Procedure to copy settings Reads Copy SettingsAssign Recipes OnlyEnable ADS? YOU SURE?Are YOU SURE? SET TempProcedure to set ready temperature SET TempSET Ready Refill Range 20 toSpray OZ/M Single Brewers Procedure to adjust the flow rate settingSpray OZ/M Dual Brewers Bypass OZ/M Single Brewers Bypass OZ/M Dual BrewersCalibrate Flow Procedures to calibrate the sprayhead flow rateCalibrate Flow ? Procedures to calibrate the bypass flow rate Brate Bypass .. Press Brew to StartProcedures to view/reset the brew counters Brew CountersFunnel Detect Server DetectServer not in Place Service Tools Programming the Brewer Nothing Pressed SERVERS?Procedure to set factory defaults Factory DefaultsTest FREQUENCY?