Bunn SNG0033000 manual SET NEW Recipes, Procedure to program the coffee name

Page 15

PROGRAMMING THE BREWER (cont.)

SET NEW RECIPES (cont.)

SET NEW RECIPE:

Using a RECIPE CARD to load coffee names and brew settings into the Single/Dual SH DBC with Smart Funnel:

The G9-2T DBC or MHG's memory contains certain coffee names. If the operator uses a coffee name that is not already stored in the grinder's memory, a RECIPE CARD can be obtained from the factory. The RECIPE CARD would include all the information needed to set up that particular coffee name. The information from the RECIPE CARD is loaded into the grinder's memory, then into the brewer's memory by holding the chip area up to the equipment's sensing coil. This informa- tion can include the coffee name, BREW VOLUMES, BYPASS PERCENTAGES, PULSE BREW TIMES, and DRIP-OUT TIMES for that particular coffee NAME. These can all be loaded in seconds.

Contact Bunn-O-Matic Corporation for the avail- ability of RECIPE CARDS.

NOTE: Instructions to program the brewer and grinder are printed on the RECIPE CARD, along with the coffee name that is being programmed.

Procedure to program the coffee name:

1.Remove the funnels (if present) from the funnel rails (both sides on DUAL brewers).

2.Position the RECIPE CARD vertically, so that the top end of the chip is beneath the funnel sensing coil (left side on DUAL brewers).

3.After a short pause the display will read CARD CON- TAINS RECIPE FOR then will change to (COFFEE NAME) SHOW QUIT SAVE. All brewing parameters for that coffee name are now transferred from the CARD to the brewer.

4.To show (view) this information, press and release SHOW. The display will scroll through all of the brew settings for all three batch sizes. The display will then return to CARD CONTAINS RECIPE FOR then will change to (COFFEE NAME) SHOW QUIT SAVE.

5.If all brew settings are correct, press SAVE. The display will read (COFFEE NAME) SETUP COM- PLETE. All brew settings for that name are now stored in the brewer's memory.

6.If the brewing information is not correct, or it is desired to exit the setup before the settings are loaded into the brewer's memory, press QUIT. The display will read (COFFEE NAME) NOT SAVED. The display will then return to the MAIN SCREEN.

READY TO BREW

WATER TEMP: 200°

POSITION CARD UNDER THE

SENSOR COIL

(left side on DUAL brewers)

CARD CONTAINS

RECIPE FOR

(COFFEE NAME)

SHOW QUIT SAVE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SCROLLS THROUGH ALL

 

 

(COFFEE NAME)

OF THE BREW SETTINGS

 

 

 

 

SETUP COMPLETE

FOR THE THREE BATCH

 

 

 

 

 

 

SIZES FOR THAT COFFEE

 

 

 

 

NAME

 

 

 

 

 

 

 

 

 

 

 

(COFFEE NAME)

NOT SAVED

Page 15

41341 080108

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Dual SH DBC BUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Programming SwitchesMain Screen Programming Lockout Switch mounted on main control boardScreen OutputsRecipes Using a Smart Funnel and a G9-2T DBC or MHG GrinderNot using a Smart Funnel and/or a G9-2T DBC or MHG Grinder Recipe Programing MethodsContinue to LevelProgram Flow Diagram Program Flow Diagram Procedure for modifying units of measure Units Setting Units of MeasureNEW Recipe ? Enable EnergysavrSET NEW Recipe Procedure for Setting the RecipeSizes DONE? SET NEW RecipeSET NEW Recipes Procedure to program the coffee nameReview RECIPES? No YES WAS the Last Recipe Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee FavorsProcedure for reviewing recipes Review RecipesBatches DONE? No YES Brew OZ Setting or Adjusting Brew VOL- UmesBypass Modifying pulse brew SET Pulse BrewSET Pulse Brew SET Pulse Brew Easy Pulse Setup SET Pulse Brew Enter Times TIMES?DONE? Batches DONE? SET PreinfusionProcedure to modify drip times Setup CompleteDrip Time now displayed on non funnel lock units as well Only Procedure to copy settingsReads Copy Settings Assign RecipesSET Temp Enable ADS?YOU SURE? Are YOU SURE?Refill Range 20 to Procedure to set ready temperatureSET Temp SET ReadyProcedure to adjust the flow rate setting Spray OZ/M Single BrewersSpray OZ/M Dual Brewers Bypass OZ/M Dual Brewers Bypass OZ/M Single BrewersProcedures to calibrate the sprayhead flow rate Calibrate FlowCalibrate Flow ? Brate Bypass .. Press Brew to Start Procedures to calibrate the bypass flow rateBrew Counters Procedures to view/reset the brew countersServer Detect Funnel DetectServer not in Place Service Tools Programming the Brewer SERVERS? Nothing PressedFactory Defaults Procedure to set factory defaultsTest FREQUENCY?
Top Page Image Contents