Manitowoc Ice QF0800, QC0700 Water Level Probe Removal, QF2300 Water Reservoir Cover Removal

Page 44

Ice Machine Operation	Section 3

Water Level Probe Removal

QF400/QC700/QF800/QF2300

Water Level Probe Removal

1.Place the toggle switch in the OFF position, turn off the water supply and disconnect electrical power to the ice machine.

2.Disconnect water supply line at float valve quick disconnect by depressing stainless steel lever.

3.Pull up on water level probes to remove.

4.Disconnect wires from water level probes or control board.

WATER LEVEL

PROBES

SV2043

QF400

WATER LEVEL

PROBES

SV2028

QC700/QF800

WATER LEVEL

PROBES

SV1791

QF2300

Water Reservoir Cover Removal

1.Place the toggle switch in the OFF position, turn off the water supply and disconnect electrical power to the ice machine.

2.Remove water level probes.

3.Remove water float valve coil.

4.Depress coil and rotate 1/4 turn counterclockwise.

5.With coil wires attached, lift coil off enclosure tube.

6.QF0800/QC0700 ONLY Rotate quarter turn fasteners counterclockwise.

7.QF0800/QC0700 ONLY Remove cotter key and pin from ice chute.

8.Remove top cover from float reservoir.

4

5

3

6

SV2030

QC700/QF800 Shown

3-12	Part Number 000002688

Image 44

Contents Installation Use and Care Manual Read These Before Proceeding Personal Injury PotentialTable of Contents Table of Contents Section Ice Machine OperationTable of Contents Section Ice Machine Sequence of Operation Section Before Calling ServiceTable of Contents How to Read a Model Number AccessoriesModel Numbers Remote Condensing UnitGeneral Information Section Model/Serial Number Location Model/Serial Number Location Ice Machine Model NumberCommercial Warranty Coverage General Information Section Ice Machine Dimensions QF400 AIR Cooled ICE MachineQC700/QF800 Water Cooled ICE Machine QC700/QF800 AIR Cooled ICE MachineQF2300 Head Section and RFC2385 Remote Condensing Unit Bin Model Dimension a Dimension B Inch 56 CM ICE Storage Bins Inch 130 CM ICE Storage BinsInch 76 CM ICE Storage Bins B970Bin Model Dimension a Width Dimension B Height Inch 76 CMSection Installation Instructions Location of Ice Machine Ice Machine Head Section Clearance RequirementsIce Machine Heat of Rejection Location of Remote Condensing UnitCondenser Air Baffle Leveling Leg and FootQC700/QF800 Air-Cooled Ice Machines Only Air BaffleSection Installation Instructions Electrical Service Ice Machine Head Section Installation Instructions Section Electrical RequirementsFor United Kingdom Only QF2300 ICE Machine Head /60/1 QC700C/QF800C ICE Machine Head /1/60 or 208-230/1/60QC700C/QF800C ICE Machine Head /1/50 RFC2385 Remote Condensing Unit 208-230/1/60 Section Installation Instructions Water Supply and Drains Cooling Tower Applications Water-Cooled ModelsPotable Water Supply Potable Water Inlet LinesWater Supply and Drain Line SIZING/CONNECTIONS Installation Instructions SectionTypical Water Supply Drain Installation Factory Equipment Refrigeration Amounts QF2300/RFC2385 onlyUsage with NON-MANITOWOC Condensing Units Line SET Length Line SET Rise or DropRoof/Wall Penetration Route Refrigeration TubingService Loop Supplied service loop is an installation requirementSuction Line OIL Traps Manitowoc S-Trap KitConnect The Line Set To The Remote Condensing Unit Connecting the line setConnect The Line Set To The Ice Machine Head Section Open The Valves Prior To Starting The Ice Machine Torque Value’sOpen Receiver Service Valve Leak Check The Refrigeration SystemInsulation Requirements Suction Liquid Min. Insulation LineSuction Shut Off Valve Insulation Typical Remote System Installation Section Installation Instructions Installation Checklist Remote AIR-COOLED onlyPotential Personal Injury Situation Component Identification ICE Machine Head SectionQC700/QF800 QF400Ice Machine Operation Section QF2300Section Ice Machine Operation Operational Checks Water Level CheckExterior Cleaning Cleaning/Sanitizing ProcedureHeavily Scaled Cleaning Procedure Cleaning the Condenser Air-Cooled CondenserSelf-Contained Air-Cooled Filter Straighten Bent Condenser FinsMANITOWOC’S Cleaning Technology Model Amount of CleanerPreventative Maintenance Cleaning Procedure QF400 Amount of Water Amount of Sanitizer CLEANING/SANITIZING Procedure QC700/QF800/QF2300Amount of Water Amount of Cleaner CLEANING/SANITIZING Procedure QF400 Mix Cleaner and Water Use Ice machine cleanerCleaner OnlyMixed With Removal of Parts for CLEANING/SANITIZINGSolution Type Water Level Probe Removal QF2300 Water Reservoir Cover RemovalQC700/QF800 Shown Water Level Probe RemovalQF2300 Shown Float Valve Removal Water Reservoir Removal QC700/QF800 Shown Ice Diverter RemovalIce Chute Removal Bin Door Removal Cabinet RemovalDump Valve Disassembly Water Dump ValveWater Cooled Condensing Unit Pry Open the Water Regulating ValveFlush Sequence in the ICE Position QF400/QC700/QF800Prior to START-UP Ice Machine Sequence of Operation Section QF2300 Checklist Problem Possible Cause To CorrectStandby Mode Before Calling Service Section Safeguard FeatureReset Procedure Safeguard Indicator Lights Analyzing Why SafeGuards May Stop the Ice Machine No Water ChecklistSafeguard Modes Possible Problem List Corrective Action ListGear Motor Speed Before Calling Service SectionGear Motor Speed Checklist Temperature is Too High or Low QF400/QC700/QF800 Temperature Sensor ChecklistThis page Intentionally Left Blank Page Manitowoc ICE, INC

Related manuals

Manual 150 pages 297 b