GE Monogram Built-In Dishwashers installation instructions Slide Dishwasher Into Final Position

Page 10

Installation Instructions

STEP 11 INSERT DRAIN HOSE THROUGH CABINET

•Position dishwasher in front of cabinet opening. Insert drain hose into the hole in cabinet side. If a power cord is used, guide the end through a separate hole.

STEP 13 SLIDE DISHWASHER INTO

FINAL POSITION

• Push the dishwasher the rest of the way into

the cabinet .

• Push the sides with your hands. Do not push the

dishwasher with your knee, as this will damage

Insulation

Blanket

Figure R

		Maximum
	Water	Drain Hose
	Water	Length 10'
	Line	Length 10'
	Line
	Drain
	Hose
	Power Cord	House Wiring
	Power Cord	(If Power Cord
	(If Used)	is NOT Used)

the door.

• Check that the tub insulation blanket does not get

“bunched-up” or interfere with the springs as you

slide it into the cabinet .

• Center the dishwasher in the opening.

• Front of door panel should be flush with face of

cabinet .

• Carefully open and close the door to ensure that

the door panel does not catch or rub on the cabinet

frame. Refer to Figure T below.

• If the door catches or rubs on the frame, reposition

and/or level the unit (see Step 14) until the door moves

TIP: Position water line and house wiring on the floor to avoid interference with base of dishwasher.

STEP 12 SLIDE DISHWASHER THREE-

FOURTHS OF THE

WAY INTO CABINET

IMPORTANT— DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR.

•Grasp the dishwasher by its sides and slide it into the opening a few inches at a time.



	Do not push against front door		Figure S


	panel with knee. Damage to
	the door panel will occur.

•As you proceed, pull the drain hose through the opening under the sink. Stop pushing when the front of the dishwasher is a few inches forward of adjacent cabinets.

•Make sure drain hose is not kinked under the dishwasher and there is no interference with the water line, wiring or any other component .

TIP: Make sure the dishwasher will fit in the cabinet . Check to be sure the power cable, drain hose, and hot water line are not trapped behind the dishwasher. Utility lines trapped behind the dishwasher prevent the dishwasher from being pushed fully into the enclosure.

10

freely and does not contact the cabinet frame.

Door Fits and

Swings Back

Behind Cabinet

Frame

	Correct				Incorrect
	Alignment		Door Catches on		Alignment
			Cabinet Frame
Figure T

Image 10

Contents Installation Instructions 31-30246Contents Safety InformationRead Carefully Keep These Instructions Materials YOU will Need Installation PreparationParts Supplied Tools YOU will NeedAdvance Planning Prepare Dishwasher EnclosureCheck to be sure that drain plug has Connecting drain line to disposerPrepare Drain Plumbing Been removed. Dishwasher willCabinet Preparation and Wire Routing Prepare Electrical WiringGrounding Instructions-Power Cord Models Grounding Instructions-Permanent ConnectionInstall Trim Pieces Installation InstructionsLocate Installation Items Prepare HOT Water SupplyRemove Toekick Remove Wood BASE, Install Leveling LegsCheck Door Balance Remove Toekick BraceInstall 90 Elbow Install Power CordPosition Water Line Housing Wiring Tip for quiet drain pump operationSlide Dishwasher Three Fourths WAY Into Cabinet Slide Dishwasher Into Final PositionInsert Drain Hose Through Cabinet Level Dishwasher Special Considerations for PositioningConnect Water Supply Insert the drain hose into the air gap as shown Drain Line InstallationConnect Drain Line Check to be sure that drain plugPretest Check List Connect Power SupplySee Steps 9 Dishwasher WET Test Installation Instructions/Custom Panel DimensionsInstall Sound Upgrade KIT if Equipped SET Water HardnessLocate toekick and screws set aside in step Install ToekickLiterature Pub. No Part No C1559P184Instructions d’installation Lire Attentivement IL Faut Garder CES Instructions Durée d’installation 1 à 3 heuresInformation de sécurité ContenuPièces Fournies Préparation pour l’installationPour les installations initiales seulement Matériaux NécessairesPlanification Préalable Préparation DE L’ENCEINTE DU LAVE-VAISSELLEPréparation DE LA Plomberie DE Vidange Mise à la terre-Branchement direct Préparation Pour LE Branchement ÉlectriqueAlimentation électrique La terre conformément aux codes et règlements locauxÉtape 2 Installation DES Pièces DE Finition Instructions d’installationÉtape 1 Repérage DES Articles Installer Preparation DU Tuyau D’EAU ChaudeType 1 Câble à un trou Étape 5 Retrait DE LA PlintheType 2 Câble à trois trous ET DES Fils DE LA Maison Instructions dinstallationÉtape 8 Installation DU Coude Angle Droit Étape 10 Raccordement DU TuyauÉtape 13 Glissement DU LAVE- Vaisselle À SA Position Finale Étape 11 Insertion DU Tuyau DE Vidange À Travers L’ARMOIREÉtape 14 Mise À Niveau DU LAVE-VAISSELLE Les commandes sur ces modèles sont conçues pour êtreConsidérations spéciales concernant la mise en place Aurez besoin de 2 vis à Étape 16 Raccordement À L’ALIMENTATION D’EAUDans cette étape, vous Mises de côté à l’étapeInstallation DU Tuyau DE Vidange Étape 17 Raccordement DU Tuyau DE VidangeVérifier que le système est hors tension Arrêt Off Qui recouvre le panneau de commande et la portePour éviter des frais de service superflus, s’assurer Ouvrir la porte et enlever tout emballage en mousseÉtape 20 Essai DU LAVE-VAISSELLE Avec DE L’EAU ’AMÉLIORATION DE L’INSONORISATION Certains ModèlesRepérer la plinthe et les vis mises de côté à l’étape Étape 23 Installation DE LA PlintheÉtape 24 Documentation Pub. Nº Pièce Nº 206C1559P184