Miele KM 326G manual Electrical connection, This appliance must be grounded

Page 14

Electrical connection

Gas connection

The automatic ignition and the safety device require connect ion to an A.C. single phase 120 V, 60 Hz supply. Fuse rating 6 A.

The appliances are factory equipped with a power supply cord with molded three prong plug

–ready for connection to an electrically grounded socket which complies with your local electrical codes or with the National Electrical Code ANSI/NFPA No. 70 for the USA or Electrical Code Part I for Canada.

Ensure that the receptacle is positioned so that it is easily accessible when the appliance is built in.

Check that the data given on the data plate under the appliance complies with the mains voltage.

Warning:

This appliance must be grounded.

Do not cut or remove the grounding prong from the plug.

12

These appliances must be installed with a separate shut-off valve and a gas pressure regulator.

Both shut-off valve and pressure regulator must be easily accessible to the consumer.

The shut-off valve is solely intended to be used to shut off the gas supply.

This appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system.

The hob comes equipped for natural gas.

You should find out details about the type of gas and calorific value from your Gas Utility and compare this information with the type of gas quoted on the data plate.

Before using the appliance, check the connection with a soapy solution for leaks. Never use a flame of any sort. The interior of this appliance has been tested by the manufacturer.

Pressure regulator

A pressure regulator is included with the appliance.

After installing a gas shut-off valve in an easily accessible location under the hob, install the gas pressure regulator to the manifold pipe using pipe dope on threads of the manifold pipe (see also next page).

Page 13 Page 15
Image 14
Page 13 Page 15
Contents T . n r 2 2 9 2 0 / T 9 1 7 0 1 B Mode demploi du kit de conversion AH 102 C4U English FrançaisPage Control knobs with marking Safety control Burner ringGeneral Marking Burner capPage Before starting check AdviceImportant notes for the user High-speed and super high-speed burners Lighting and adjustingGas burners Zone super high-speed wok burner Outer ringMake sure the trivet is securely fixed to the pot support How to use gas burnersPlace the pot over the pot support fitted above the hob ˝ 50 mm between the pot and a heat-sensitive worktopMaking sauces Keeping food hot Cooking through/simmering Cooking in comfortAre best done on the super high-speed wok Burner Cleaning and maintenance Tab IndentationCont Appliance Ignition sparks but burner TroubleshootingProblem Cause Solution Burner does not burn well Does not igniteElectrical circuit diagram Electrical connection This appliance must be groundedFor USA only Gas pressures for USANominal rating natural gas 4˝ For Canada onlyGas pressures for Canada Building-in dimensions Clearance above and around the appliance Wall strips must be heat-resistantAir inlets at the back of the hob are clear Building-inPlace the hob in the cut-out. Check that Secure the hob in position. The bracketsPage Part Safety InstructionsConversion kit Type number AH 102 C4U Conversion instructionsFor future use DisassemblyConversion instructions IgniterPurposes. Check gas pressure. Permitted Locations of injectors and minimum adjustment screwsPressure regulator conversion High speed and super high speed burner ConversionHand side of the wok burner body a Wok burner outer ring conversionWok burner inner ring conversion WayTwo 12 mm wrenches are needed to separate the fittings Reference tableThis concludes conversion. The hob can now be reassembled Minimum adjustment screwsAssembly Installing appliance Testing converted applianceWarranty and service Energy source Technical detailsModel number KM 326G Gas source Overall wattage, electricity Total burnerrate Natural gasPage
Top Page Image Contents