Miele KM 326G manual Conversion instructions, Disassembly, For future use, Igniter

Page 22

Conversion instructions

Caution

Before proceeding with the conversion, shut off the gas supply to the appliance prior to disconnecting the electrical power.

Remove the three screws securing the dual ring wok burner. Remove the wok burner base plate. Lift the ceramic tray from the hob.

Note

Disassembly

Shut off gas supply, disconnect the manifold pipe, disconnect the electrical power. Remove pan supports, burner heads and burner rings. Remove control knobs.

Each regulator shaft is equipped with a black ring. This ring may cling to the rubber seal in the ceramic tray. Check and remove the rings from the rubber seals.

For future use

In the event that the hob is built in, undo the

Save the orifices removed from the appliance

bracket clamps underneath the work surface.

for future use. For converting this appliance

Lift the hob on to the work surface.

back to Natural gas, follow the instructions and

use the numbers in brackets (… ).

Unscrew the venturis on the high-speed and

super high-speed burners using a 20 mm

Igniter

wrench. Lift and remove the burner rings and

The relationship between the igniter and the

burner base plates. Disconnect the wires from

main burners can't be changed. The relationship

the ignition plugs. Keep the wire from dropping

in the case of LP gas and natural gas is identical.

into the undertray by inserting it in one of the

The distance between the igniter and the high

slots in the burner supports.

speed burner and super high speed burner is

± 3.5 mm. For the two zone

high speed burner the

distance between the

igniter and the inner ring is

± 2.5 mm.

Remove the top five screws in the back of the

hob undertray.

20

Image 22

Contents T . n r 2 2 9 2 0 / T 9 1 7 0 1 B Mode demploi du kit de conversion AH 102 C4U English FrançaisPage Control knobs with marking Safety control Burner ringGeneral Marking Burner capPage Important notes for the user AdviceBefore starting check High-speed and super high-speed burners Lighting and adjustingGas burners Zone super high-speed wok burner Outer ringMake sure the trivet is securely fixed to the pot support How to use gas burnersPlace the pot over the pot support fitted above the hob ˝ 50 mm between the pot and a heat-sensitive worktopAre best done on the super high-speed wok Burner Cooking in comfortMaking sauces Keeping food hot Cooking through/simmering Cleaning and maintenance Tab IndentationCont Appliance Ignition sparks but burner TroubleshootingProblem Cause Solution Burner does not burn well Does not igniteElectrical circuit diagram Electrical connection This appliance must be groundedFor USA only Gas pressures for USAGas pressures for Canada For Canada onlyNominal rating natural gas 4˝ Building-in dimensions Clearance above and around the appliance Wall strips must be heat-resistantAir inlets at the back of the hob are clear Building-inPlace the hob in the cut-out. Check that Secure the hob in position. The bracketsPage Part Safety InstructionsConversion kit Type number AH 102 C4U Conversion instructionsFor future use DisassemblyConversion instructions IgniterPurposes. Check gas pressure. Permitted Locations of injectors and minimum adjustment screwsPressure regulator conversion High speed and super high speed burner ConversionHand side of the wok burner body a Wok burner outer ring conversionWok burner inner ring conversion WayTwo 12 mm wrenches are needed to separate the fittings Reference tableAssembly Minimum adjustment screwsThis concludes conversion. The hob can now be reassembled Installing appliance Testing converted applianceWarranty and service Energy source Technical detailsModel number KM 326G Gas source Overall wattage, electricity Total burnerrate Natural gasPage