Mitsubishi Electronics 882.00207.00 specifications Typical Inventory Display Operator Screen

Page 49

While the blending system is in operation, there are a couple of displays available to the operator. These displays are selected simply by pressing the “NEXT” key when the unit is running. The default display shown when the blender is in run mode is the Recipe Screen.

The Recipe Screen indicates by feeder number, the amount of material metered into the weigh hopper assembly by that particular feeder. This display is updated after each component dispenses its specified amount. The ingredient weights (Unit Values) are in pounds, unless the metric display is selected.

Pressing the “NEXT” key when in the default recipe mode display will toggle to the next screen, which is the Inventory Display. This can be done at any time, but if the blender is in a critical mode such as dumping, and updating inventory, etc., it may ignore the keystroke. Simply press the “NEXT” key again, the Inventory screen will be displayed.

Figure 35: Typical Inventory Display Operator Screen

This display indicates the amount of material in pounds that has been used by each feeder of the recipe. It is important to note that the weights are rounded off to the closest pound. On minor ingredients, several cycles may have to occur to show an inventory number.

In addition to showing the amount of material that has been used for each feeder, this screen is also a summary display that shows the total inventory, the time for the last batch, and the average rate of the blender.

If the blender is run in “Percentage Mode” instead of “Quickset” Mode during operation, the “Percentage Mode” will use the blender inventory numbers shown on the Inventory screen to calculate the percentages for each ingredient. It is important to zero the inventories when a recipe is changed to have this screen accurately reflect the current percentages of the recipe in-process.

Note: Blender inventories must be cleared when the current recipe is started to show accurate percentages for the current recipe.

Note: To clear inventories, press the “Clear Inventory” key on the “Inventory” print screen.

Recipe Entry Formats

The Slide Gate/Auger System contains several operator friendly recipe menus. This section of the manual lists these recipe menus:

•Recipe Page (Start/Setup)

•Recipe Book Page

•Recipe Format

Bulletin Number

Chapter 4: Operation

48 of 102

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Gravimetric Slide Gate Batch Blender Mitsubishi Controller Parts and Service Department Event of Shipping Damage Unpacking and InspectionIf the Shipment is Not Complete If the Shipment is Not CorrectReturns Warranty ReturnsCredit Returns Table of Contents Maintenance Customer Responsibilities Technical Specifications Safety Symbols Used in this Manual How to Use This ManualSafety Tags and Warning Labels Description Wear Safety Glasses and Work Gloves Follow all Safety CodesGeneral Responsibility ResponsibilityOperator Responsibility Remember Reporting a Safety Defect Maintenance ResponsibilityCustomer Service AccessoriesModels Covered in This Manual General DescriptionEquipment Specifications Mechanical Features Typical Features and ComponentsController Features Supply Hoppers System Component DescriptionSlide Gates Weigh Hopper Typical Slide Gate AssemblyTypical Weigh Hopper Assembly Operator Control Panel Display Mix ChamberFunction Typical Operator Screens Typical Setup Screens Bulletin Number Functional Description Pneumatic Slide Gate below Mixer Optional ComponentsLow Level Sensors Mezzanine and Floor StandsAdditive Feeder Hopper Regrind Auger Metering R.A.M. HopperTake-off Compartments Safety Circuit Standards Safety FeaturesSafety Device Lock-Outs Fail Safe OperationTwist Cap Plug Connected to Each Feeder Auger Motor Electrical Disconnect PlugElectrical Safety Interlock Switch Located on mixer door Electric Safety Interlock SwitchUncrating the Equipment Mechanical InstallationSite Requirements Mounting ConfigurationsMachine Mount Typical Mezzanine Mounted Batch Blender Mezzanine MountTypical Floor Mount Central Blender Layout Floor Mount Central BlenderPneumatic Connections Electrical ConnectionsMechanical Set-up Initial Set-upStroke Limiters for Metering Gates Weigh Hopper Final Connections Weigh Hopper InstallationController Set-up Display Main Recipe ScreenRecipe Page Start Blender Controller Menu StructureBlender Calibration Display Calibration Menu Screen Feeder Calibration Auger Blenders Alarm SetupSetting Date and Time Network SetupAdditional Setup Parameters Initial Startup Start-up Quick Start ProcedureGeneral Operation New RecipesExisting Recipes Operation ProceduresTypical Recipe Entry Operator Screen Operator DisplaysRecipe Entry Formats Typical Inventory Display Operator ScreenRecipe Format Menu Quickset Mode Most common in injection molding Example Calculations of a 5-component blend in Quickset mode Switching Modes Percentage Mode Most common in extrusion and blow moldingRecipe Setup Current Recipe MenuInventory Shutdown Typical Batch Sizes Blender Batch Size lbsMixer and Dump Setup Weigh Hopper Dump Delay Time Re-Mix TimerWeigh Hopper Dump Time Weigh Hopper Dump Cycle Alarm FlagsMixer Dump Time Calibration Error Typical PLC Battery Low Alarm Screen Feeder Clean Out Recipe Book Tree Diagram in -5 of this manualSave Running Recipe to the Book Display Recipe ContentsLoad a Saved Recipe from the Book Color Changes Erase Recipe or Entire BookTypical Inventory Shutdown Operator Screen Shut-downSample Preventative Maintenance Schedule Preventative Maintenance ScheduleCorrective Maintenance Preventative MaintenanceElectrical Internal Components of the Control PanelOutput Signals from Programmable Controller Input Signals to Programmable ControllerIntroduction TroubleshootingProblem Corrective action Problem Corrective action Warranty will be voided Service Department Warranty Specifications WarrantyWarranty Restrictions Warranty LiabilitiesEquipment Specifications Technical SpecificationsCustomer Responsibilities Annex B Information Final Assembly Drawings and DiagramsMixer Sub-Assembly Typical Mixer Assembly Parts List Typical Hopper Assembly Parts List Hopper Sub-assemblyTypical R.A.M. Hopper Assembly Parts List Hopper R.A.M. Regrind Auger Metering Sub-Assembly OptionalTypical Additive Feeder Hopper Assembly Parts List Hopper Additive Feeder Sub-Assembly OptionalTypical Weigh Hopper Assembly Parts List Weigh Hopper Sub-assemblyTypical Slidegate Assembly Parts List Slide Gate Sub-assemblyTypical Knife Gate below mixer Assembly Parts List Knife Gate Sub-assembly HD OptionalTypical Knife Gate floor stand Assembly Parts List Knife Gate Sub-assembly RD OptionalControl Panel Layout Typical Mitsubishi Controller Main Parts ListSpare Parts Kits Blender Spare Parts ListingPasswords Addendum Service Supervisor InformationProgrammable Settings Advanced Weight Options Screen Factory Setup MenuMetering Test Screen Feed Calibration Options Screen Feed Algorithm Options ScreenMechanical Options Screen Feeder SetupUnits Customer Setup MenuAlarm Log Typical Alarm Flags & Feeder Setup ScreenRecipe Format Factory Default Setup ParametersLoadcell Calex Module Dipswitch Settings General Blender Info Mitsubishi Communications ManualBlender Alarms Inventory Info Recipe Info this is Where YOU Right the NEW Recipe to Recipe Book Manipulation Fixed Decimal Explanation Alarm Number ExplanationUntil the Hopper Feeds Material Into the NEW Batch Technical Assistance Service Department Sales DepartmentParts Department Contract Department
Related manuals
Manual 103 pages 37.01 Kb

882.00207.00 specifications

Mitsubishi Electronics has always been at the forefront of innovation in the field of electronics, and one of its significant products is the Mitsubishi Electronics 882.00207.00. This device is designed for enhanced performance and reliability, providing a range of features that cater to both industrial and consumer needs.

One of the main features of the Mitsubishi 882.00207.00 is its robust design, which ensures durability in demanding environments. The device is built to withstand harsh conditions, making it ideal for industrial applications where reliability is critical. Its rugged construction means that it can operate efficiently in extreme temperatures, humidity, and other challenging conditions.

In terms of technology, the Mitsubishi 882.00207.00 incorporates advanced electronic components that enhance its functionality. This includes state-of-the-art processing capabilities that allow for quick data processing and seamless operation. The device’s integration of cutting-edge technology ensures that it meets the performance demands of modern applications while providing energy efficiency.

Another notable characteristic is its user-friendly interface. The device is designed with ease of use in mind, allowing operators to interact with it effortlessly. This ensures that even those with minimal technical expertise can operate the device effectively. The clear display and intuitive controls make it accessible for a wide range of users, facilitating smoother operations in various settings.

The Mitsubishi 882.00207.00 is also equipped with multiple connectivity options. This enables it to integrate seamlessly with other devices and systems, facilitating enhanced communication and data transfer. Whether it’s connecting to existing networks or interfacing with new technologies, the device’s versatility ensures it can adapt to evolving technological landscapes.

Additionally, the device is backed by Mitsubishi's commitment to quality and customer support. Users can expect reliable service and assistance, ensuring that they can maximize the potential of their investment.

In conclusion, the Mitsubishi Electronics 882.00207.00 stands out in the electronics market for its durable construction, advanced technology, user-friendly design, and versatile connectivity options. This makes it an invaluable tool for both industrial applications and everyday consumer use, embodying the innovative spirit that Mitsubishi Electronics is known for.
Top Page Image Contents