Mitsubishi Electronics 882.00207.00 Shut-down, Typical Inventory Shutdown Operator Screen

Page 64

8.If any other ingredients need to be changed for the next recipe, simply drain the larger hoppers with the drain tubes provided on the side of the hoppers. When the material level is below the drain tube, open the slide gate manually to dump the rest of the material. If you wish to speed the emptying process, material can be manually drained out of the slide gate assembly into a dump chute or bucket, while draining from the drain tube.

9.Using a vacuum cleaner or air hose, clean out all the hoppers that have been emptied. Always start at the uppermost part of the blender and work downward to prevent dust and pellets from falling into an already cleaned area.

WARNING! The auger metering assemblies on Auger blenders can be removed after the hoppers above them have been drained.

10.Clean the weigh hopper and mixer assemblies on the blender using a vacuum cleaner. The mixer agitator is removable for cleaning if desired.

11.Reinstall any metering units that were removed from the blender during clean out.

12.Reinstall the weigh hopper using care to center the hopper on the load cells on the weigh hopper bracket.

13.Load the blender with new material.

14.Restart the unit with the new recipe.

WARNING! Always disconnect and lockout all electrical power and pneumatic (i.e. compressed air) sources prior to servicing or cleaning any product, including all Slide Gate/Auger blending systems. Failure to do so may result in serious injury or death.

4-3 Shut-down

The Slide Gate Gravimetric Blender can be stopped in one of two ways:

1.To immediately stop the blender, the operator can touch “Abort Current Batch.” This will cause the blender to stop making the current batch immediately. Obviously, if the blender is stopped in this method then the current batch will not be completed properly.

2.If the operator desires to complete the current batch of material, then he can wait until the Inventory Shutdown value is reached. The blender will finish the current batch of material to the specifications set in the Setup portion of this manual. It will then stop and display to the operator that the inventory value has been reached. Additionally, it will flash an alarm and wait for operator attention. An example of this screen is shown below:

Figure 49: Typical Inventory Shutdown Operator Screen

Touch to make another box of material

Touch if you don’t want to make another batch

Bulletin Number

Chapter 4: Operation

63 of 102

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Gravimetric Slide Gate Batch Blender Mitsubishi Controller Parts and Service Department Unpacking and Inspection Event of Shipping DamageIf the Shipment is Not Complete If the Shipment is Not CorrectReturns Warranty ReturnsCredit Returns Table of Contents Maintenance Customer Responsibilities Technical Specifications How to Use This Manual Safety Symbols Used in this ManualSafety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work GlovesGeneral Responsibility ResponsibilityOperator Responsibility Remember Maintenance Responsibility Reporting a Safety DefectAccessories Customer ServiceModels Covered in This Manual General DescriptionEquipment Specifications Mechanical Features Typical Features and ComponentsController Features System Component Description Supply HoppersSlide Gates Typical Slide Gate Assembly Weigh HopperTypical Weigh Hopper Assembly Mix Chamber Operator Control Panel DisplayFunction Typical Operator Screens Typical Setup Screens Bulletin Number Functional Description Optional Components Pneumatic Slide Gate below MixerLow Level Sensors Mezzanine and Floor StandsAdditive Feeder Hopper Regrind Auger Metering R.A.M. HopperTake-off Compartments Safety Features Safety Circuit StandardsSafety Device Lock-Outs Fail Safe OperationElectrical Disconnect Plug Twist Cap Plug Connected to Each Feeder Auger MotorElectric Safety Interlock Switch Electrical Safety Interlock Switch Located on mixer doorMechanical Installation Uncrating the EquipmentSite Requirements Mounting ConfigurationsMachine Mount Mezzanine Mount Typical Mezzanine Mounted Batch BlenderFloor Mount Central Blender Typical Floor Mount Central Blender LayoutElectrical Connections Pneumatic ConnectionsMechanical Set-up Initial Set-upStroke Limiters for Metering Gates Weigh Hopper Installation Weigh Hopper Final ConnectionsDisplay Main Recipe Screen Controller Set-upBlender Controller Menu Structure Recipe Page StartBlender Calibration Display Calibration Menu Screen Alarm Setup Feeder Calibration Auger BlendersNetwork Setup Setting Date and TimeAdditional Setup Parameters Initial Startup Quick Start Procedure Start-upGeneral Operation New RecipesOperation Procedures Existing RecipesOperator Displays Typical Recipe Entry Operator ScreenTypical Inventory Display Operator Screen Recipe Entry FormatsRecipe Format Menu Quickset Mode Most common in injection molding Example Calculations of a 5-component blend in Quickset mode Percentage Mode Most common in extrusion and blow molding Switching ModesRecipe Setup Current Recipe MenuTypical Batch Sizes Blender Batch Size lbs Inventory ShutdownMixer and Dump Setup Weigh Hopper Dump Delay Time Re-Mix TimerWeigh Hopper Dump Time Weigh Hopper Dump Cycle Alarm FlagsMixer Dump Time Calibration Error Typical PLC Battery Low Alarm Screen Feeder Clean Out Tree Diagram in -5 of this manual Recipe BookSave Running Recipe to the Book Display Recipe ContentsLoad a Saved Recipe from the Book Erase Recipe or Entire Book Color ChangesShut-down Typical Inventory Shutdown Operator ScreenPreventative Maintenance Schedule Sample Preventative Maintenance SchedulePreventative Maintenance Corrective MaintenanceElectrical Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerTroubleshooting IntroductionProblem Corrective action Problem Corrective action Warranty will be voided Service Department Warranty Warranty SpecificationsWarranty Restrictions Warranty LiabilitiesEquipment Specifications Technical SpecificationsCustomer Responsibilities Annex B Information Drawings and Diagrams Final AssemblyMixer Sub-Assembly Typical Mixer Assembly Parts List Hopper Sub-assembly Typical Hopper Assembly Parts ListHopper R.A.M. Regrind Auger Metering Sub-Assembly Optional Typical R.A.M. Hopper Assembly Parts ListHopper Additive Feeder Sub-Assembly Optional Typical Additive Feeder Hopper Assembly Parts ListWeigh Hopper Sub-assembly Typical Weigh Hopper Assembly Parts ListSlide Gate Sub-assembly Typical Slidegate Assembly Parts ListKnife Gate Sub-assembly HD Optional Typical Knife Gate below mixer Assembly Parts ListKnife Gate Sub-assembly RD Optional Typical Knife Gate floor stand Assembly Parts ListTypical Mitsubishi Controller Main Parts List Control Panel LayoutBlender Spare Parts Listing Spare Parts KitsPasswords Addendum Service Supervisor InformationProgrammable Settings Advanced Weight Options Screen Factory Setup MenuMetering Test Screen Feed Algorithm Options Screen Feed Calibration Options ScreenFeeder Setup Mechanical Options ScreenCustomer Setup Menu UnitsTypical Alarm Flags & Feeder Setup Screen Alarm LogFactory Default Setup Parameters Recipe FormatLoadcell Calex Module Dipswitch Settings Mitsubishi Communications Manual General Blender InfoBlender Alarms Inventory Info Recipe Info this is Where YOU Right the NEW Recipe to Recipe Book Manipulation Alarm Number Explanation Fixed Decimal ExplanationUntil the Hopper Feeds Material Into the NEW Batch Service Department Sales Department Technical AssistanceParts Department Contract Department
Related manuals
Manual 103 pages 37.01 Kb

882.00207.00 specifications

Mitsubishi Electronics has always been at the forefront of innovation in the field of electronics, and one of its significant products is the Mitsubishi Electronics 882.00207.00. This device is designed for enhanced performance and reliability, providing a range of features that cater to both industrial and consumer needs.

One of the main features of the Mitsubishi 882.00207.00 is its robust design, which ensures durability in demanding environments. The device is built to withstand harsh conditions, making it ideal for industrial applications where reliability is critical. Its rugged construction means that it can operate efficiently in extreme temperatures, humidity, and other challenging conditions.

In terms of technology, the Mitsubishi 882.00207.00 incorporates advanced electronic components that enhance its functionality. This includes state-of-the-art processing capabilities that allow for quick data processing and seamless operation. The device’s integration of cutting-edge technology ensures that it meets the performance demands of modern applications while providing energy efficiency.

Another notable characteristic is its user-friendly interface. The device is designed with ease of use in mind, allowing operators to interact with it effortlessly. This ensures that even those with minimal technical expertise can operate the device effectively. The clear display and intuitive controls make it accessible for a wide range of users, facilitating smoother operations in various settings.

The Mitsubishi 882.00207.00 is also equipped with multiple connectivity options. This enables it to integrate seamlessly with other devices and systems, facilitating enhanced communication and data transfer. Whether it’s connecting to existing networks or interfacing with new technologies, the device’s versatility ensures it can adapt to evolving technological landscapes.

Additionally, the device is backed by Mitsubishi's commitment to quality and customer support. Users can expect reliable service and assistance, ensuring that they can maximize the potential of their investment.

In conclusion, the Mitsubishi Electronics 882.00207.00 stands out in the electronics market for its durable construction, advanced technology, user-friendly design, and versatile connectivity options. This makes it an invaluable tool for both industrial applications and everyday consumer use, embodying the innovative spirit that Mitsubishi Electronics is known for.
Top Page Image Contents