Mitsubishi Electronics 882.00207.00 Typical Alarm Flags & Feeder Setup Screen, Alarm Log

Page 93

Alarm Setup

This screen allows the user to configure the feeder type for each feeder; configure whether a feeder will retry during the metering of a batch, and enable or disable the “Out of Material” alarm for any feeder. If a hopper is set to “No Retry” then the blender will continue to meter the rest of the batch even if this hopper runs out of material. No “Out of Material” alarm will be given regardless of how the alarm is configured unless the user has purchased and wired in the low level proximity switches in each hopper. To configure each hopper, perform the following steps:

1.Select a feeder by touching the “Select Feeder” box.

2.The current settings for that hopper will be shown.

3.Make the necessary adjustments and select a new feeder to configure if desired.

4. Hit “Done” to exit.

Figure 75: Typical Alarm Flags & Feeder Setup Screen

Select a Feeder to

Configure

Change the Alarm

Silence Delay

Enable or Disable Retries

Enable or Disable Alarms

Go back to Setup Directory

Alarm Log

This screen shows the last 100 stored alarms. The log can be viewed, printed and cleared.

Figure 76: Typical Alarm Log Screen

Clear Alarm

Log

Print Alarm

Log

Scroll Through

Alarm Log

Alarm Log

Go back to Setup Directory

Bulletin Number

Chapter 7: Appendix

92 of 102

Page 92 Page 94
Image 93
Page 92 Page 94
Contents Gravimetric Slide Gate Batch Blender Mitsubishi Controller Parts and Service Department Event of Shipping Damage Unpacking and InspectionIf the Shipment is Not Complete If the Shipment is Not CorrectWarranty Returns ReturnsCredit Returns Table of Contents Maintenance Customer Responsibilities Technical Specifications Safety Symbols Used in this Manual How to Use This ManualSafety Tags and Warning Labels Description Wear Safety Glasses and Work Gloves Follow all Safety CodesResponsibility General ResponsibilityOperator Responsibility Remember Reporting a Safety Defect Maintenance ResponsibilityCustomer Service AccessoriesModels Covered in This Manual General DescriptionEquipment Specifications Typical Features and Components Mechanical FeaturesController Features Supply Hoppers System Component DescriptionSlide Gates Weigh Hopper Typical Slide Gate AssemblyTypical Weigh Hopper Assembly Operator Control Panel Display Mix ChamberFunction Typical Operator Screens Typical Setup Screens Bulletin Number Functional Description Pneumatic Slide Gate below Mixer Optional ComponentsLow Level Sensors Mezzanine and Floor StandsRegrind Auger Metering R.A.M. Hopper Additive Feeder HopperTake-off Compartments Safety Circuit Standards Safety FeaturesSafety Device Lock-Outs Fail Safe OperationTwist Cap Plug Connected to Each Feeder Auger Motor Electrical Disconnect PlugElectrical Safety Interlock Switch Located on mixer door Electric Safety Interlock SwitchUncrating the Equipment Mechanical InstallationMounting Configurations Site RequirementsMachine Mount Typical Mezzanine Mounted Batch Blender Mezzanine MountTypical Floor Mount Central Blender Layout Floor Mount Central BlenderPneumatic Connections Electrical ConnectionsInitial Set-up Mechanical Set-upStroke Limiters for Metering Gates Weigh Hopper Final Connections Weigh Hopper InstallationController Set-up Display Main Recipe ScreenRecipe Page Start Blender Controller Menu StructureBlender Calibration Display Calibration Menu Screen Feeder Calibration Auger Blenders Alarm SetupSetting Date and Time Network SetupAdditional Setup Parameters Initial Startup Start-up Quick Start ProcedureGeneral Operation New RecipesExisting Recipes Operation ProceduresTypical Recipe Entry Operator Screen Operator DisplaysRecipe Entry Formats Typical Inventory Display Operator ScreenRecipe Format Menu Quickset Mode Most common in injection molding Example Calculations of a 5-component blend in Quickset mode Switching Modes Percentage Mode Most common in extrusion and blow moldingRecipe Setup Current Recipe MenuInventory Shutdown Typical Batch Sizes Blender Batch Size lbsMixer and Dump Setup Re-Mix Timer Weigh Hopper Dump Delay TimeWeigh Hopper Dump Time Alarm Flags Weigh Hopper Dump CycleMixer Dump Time Calibration Error Typical PLC Battery Low Alarm Screen Feeder Clean Out Recipe Book Tree Diagram in -5 of this manualDisplay Recipe Contents Save Running Recipe to the BookLoad a Saved Recipe from the Book Color Changes Erase Recipe or Entire BookTypical Inventory Shutdown Operator Screen Shut-downSample Preventative Maintenance Schedule Preventative Maintenance ScheduleCorrective Maintenance Preventative MaintenanceElectrical Internal Components of the Control PanelOutput Signals from Programmable Controller Input Signals to Programmable ControllerIntroduction TroubleshootingProblem Corrective action Problem Corrective action Warranty will be voided Service Department Warranty Specifications WarrantyWarranty Restrictions Warranty LiabilitiesTechnical Specifications Equipment SpecificationsCustomer Responsibilities Annex B Information Final Assembly Drawings and DiagramsMixer Sub-Assembly Typical Mixer Assembly Parts List Typical Hopper Assembly Parts List Hopper Sub-assemblyTypical R.A.M. Hopper Assembly Parts List Hopper R.A.M. Regrind Auger Metering Sub-Assembly OptionalTypical Additive Feeder Hopper Assembly Parts List Hopper Additive Feeder Sub-Assembly OptionalTypical Weigh Hopper Assembly Parts List Weigh Hopper Sub-assemblyTypical Slidegate Assembly Parts List Slide Gate Sub-assemblyTypical Knife Gate below mixer Assembly Parts List Knife Gate Sub-assembly HD OptionalTypical Knife Gate floor stand Assembly Parts List Knife Gate Sub-assembly RD OptionalControl Panel Layout Typical Mitsubishi Controller Main Parts ListSpare Parts Kits Blender Spare Parts ListingAddendum Service Supervisor Information PasswordsProgrammable Settings Factory Setup Menu Advanced Weight Options ScreenMetering Test Screen Feed Calibration Options Screen Feed Algorithm Options ScreenMechanical Options Screen Feeder SetupUnits Customer Setup MenuAlarm Log Typical Alarm Flags & Feeder Setup ScreenRecipe Format Factory Default Setup ParametersLoadcell Calex Module Dipswitch Settings General Blender Info Mitsubishi Communications ManualBlender Alarms Inventory Info Recipe Info this is Where YOU Right the NEW Recipe to Recipe Book Manipulation Fixed Decimal Explanation Alarm Number ExplanationUntil the Hopper Feeds Material Into the NEW Batch Technical Assistance Service Department Sales DepartmentParts Department Contract Department
Related manuals
Manual 103 pages 37.01 Kb

882.00207.00 specifications

Mitsubishi Electronics has always been at the forefront of innovation in the field of electronics, and one of its significant products is the Mitsubishi Electronics 882.00207.00. This device is designed for enhanced performance and reliability, providing a range of features that cater to both industrial and consumer needs.

One of the main features of the Mitsubishi 882.00207.00 is its robust design, which ensures durability in demanding environments. The device is built to withstand harsh conditions, making it ideal for industrial applications where reliability is critical. Its rugged construction means that it can operate efficiently in extreme temperatures, humidity, and other challenging conditions.

In terms of technology, the Mitsubishi 882.00207.00 incorporates advanced electronic components that enhance its functionality. This includes state-of-the-art processing capabilities that allow for quick data processing and seamless operation. The device’s integration of cutting-edge technology ensures that it meets the performance demands of modern applications while providing energy efficiency.

Another notable characteristic is its user-friendly interface. The device is designed with ease of use in mind, allowing operators to interact with it effortlessly. This ensures that even those with minimal technical expertise can operate the device effectively. The clear display and intuitive controls make it accessible for a wide range of users, facilitating smoother operations in various settings.

The Mitsubishi 882.00207.00 is also equipped with multiple connectivity options. This enables it to integrate seamlessly with other devices and systems, facilitating enhanced communication and data transfer. Whether it’s connecting to existing networks or interfacing with new technologies, the device’s versatility ensures it can adapt to evolving technological landscapes.

Additionally, the device is backed by Mitsubishi's commitment to quality and customer support. Users can expect reliable service and assistance, ensuring that they can maximize the potential of their investment.

In conclusion, the Mitsubishi Electronics 882.00207.00 stands out in the electronics market for its durable construction, advanced technology, user-friendly design, and versatile connectivity options. This makes it an invaluable tool for both industrial applications and everyday consumer use, embodying the innovative spirit that Mitsubishi Electronics is known for.
Top Page Image Contents