Mitsubishi Electronics 882.00207.00 Save Running Recipe to the Book, Display Recipe Contents

Page 62

Figure 48: Typical Recipe Book Operator Screen

Select a Stored

Recipe

Stored Recipe

Details

Save Running Recipe to the Book

Erase One

Stored Recipe

Erase Entire

Book

Load Stored

Recipe

Go to Recipe

Page

The save current recipe to book function allows the operator to save the contents of the current recipe to the recipe book under a desired number.

Upon selecting this function, the operator will be prompted for a reference recipe number. This may be any number from 1 to 50.

The assigned recipe number will be used for all further references to this recipe until deleted. The operator should be familiar with the recipe numbers used. We suggest keeping a loose- leaf notebook with 50 tabbed pages as a reference to what is kept in the blender so this can be the standard for all blenders in the plant, etc. To save a running recipe to the Recipe Book perform the following steps:

1.Enter the Recipe Book by touching the Recipe Book icon located on the Recipe Screen.

2.Select a stored recipe by changing the number next to “Recipe #.”

3.Touch “Save Running Recipe” and then “Done”.

Load a Saved Recipe from the Book

The load from book function allows the operator to retrieve a previously stored recipe from the recipe book and install it into the current recipe menu. This will overwrite the current recipe, so make sure that it has been saved to the book before installing a new recipe in its place. To load a previously stored recipe from the Recipe Book:

1.Enter the Recipe Book by touching the Recipe Book icon located on the Recipe Screen.

2.Select a stored recipe by changing the number next to “Recipe #.”

3.Touch “Load” and then “Done” (this takes you back to the Recipe Screen).

4.Touch “Accept New Recipe” to accept the loaded recipe into the blender.

Note: If replacing the current recipe with one that is downloaded from the Recipe Book, make sure that the previous recipe has been saved, as it will be overwritten by the new downloaded recipe.

Display Recipe Contents

The display recipe function is used to verify the contents of a recipe number before it is loaded from the recipe book. In order to view the desired recipe, the operator must enter the

Bulletin Number

Chapter 4: Operation

61 of 102

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Gravimetric Slide Gate Batch Blender Mitsubishi Controller Parts and Service Department If the Shipment is Not Complete Unpacking and InspectionEvent of Shipping Damage If the Shipment is Not CorrectCredit Returns Warranty ReturnsReturns Table of Contents Maintenance Customer Responsibilities Technical Specifications How to Use This Manual Safety Symbols Used in this ManualSafety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work GlovesOperator Responsibility ResponsibilityGeneral Responsibility Remember Maintenance Responsibility Reporting a Safety DefectModels Covered in This Manual AccessoriesCustomer Service General DescriptionEquipment Specifications Controller Features Typical Features and ComponentsMechanical Features System Component Description Supply HoppersSlide Gates Typical Slide Gate Assembly Weigh HopperTypical Weigh Hopper Assembly Mix Chamber Operator Control Panel DisplayFunction Typical Operator Screens Typical Setup Screens Bulletin Number Functional Description Low Level Sensors Optional ComponentsPneumatic Slide Gate below Mixer Mezzanine and Floor StandsTake-off Compartments Regrind Auger Metering R.A.M. HopperAdditive Feeder Hopper Safety Device Lock-Outs Safety FeaturesSafety Circuit Standards Fail Safe OperationElectrical Disconnect Plug Twist Cap Plug Connected to Each Feeder Auger MotorElectric Safety Interlock Switch Electrical Safety Interlock Switch Located on mixer doorMechanical Installation Uncrating the EquipmentMachine Mount Mounting ConfigurationsSite Requirements Mezzanine Mount Typical Mezzanine Mounted Batch BlenderFloor Mount Central Blender Typical Floor Mount Central Blender LayoutElectrical Connections Pneumatic ConnectionsStroke Limiters for Metering Gates Initial Set-upMechanical Set-up Weigh Hopper Installation Weigh Hopper Final ConnectionsDisplay Main Recipe Screen Controller Set-upBlender Controller Menu Structure Recipe Page StartBlender Calibration Display Calibration Menu Screen Alarm Setup Feeder Calibration Auger BlendersNetwork Setup Setting Date and TimeAdditional Setup Parameters Initial Startup General Operation Quick Start ProcedureStart-up New RecipesOperation Procedures Existing RecipesOperator Displays Typical Recipe Entry Operator ScreenTypical Inventory Display Operator Screen Recipe Entry FormatsRecipe Format Menu Quickset Mode Most common in injection molding Example Calculations of a 5-component blend in Quickset mode Recipe Setup Percentage Mode Most common in extrusion and blow moldingSwitching Modes Current Recipe MenuTypical Batch Sizes Blender Batch Size lbs Inventory ShutdownMixer and Dump Setup Weigh Hopper Dump Time Re-Mix TimerWeigh Hopper Dump Delay Time Mixer Dump Time Alarm FlagsWeigh Hopper Dump Cycle Calibration Error Typical PLC Battery Low Alarm Screen Feeder Clean Out Tree Diagram in -5 of this manual Recipe BookLoad a Saved Recipe from the Book Display Recipe ContentsSave Running Recipe to the Book Erase Recipe or Entire Book Color ChangesShut-down Typical Inventory Shutdown Operator ScreenPreventative Maintenance Schedule Sample Preventative Maintenance ScheduleElectrical Preventative MaintenanceCorrective Maintenance Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerTroubleshooting IntroductionProblem Corrective action Problem Corrective action Warranty will be voided Service Department Warranty Restrictions WarrantyWarranty Specifications Warranty LiabilitiesCustomer Responsibilities Technical SpecificationsEquipment Specifications Annex B Information Drawings and Diagrams Final AssemblyMixer Sub-Assembly Typical Mixer Assembly Parts List Hopper Sub-assembly Typical Hopper Assembly Parts ListHopper R.A.M. Regrind Auger Metering Sub-Assembly Optional Typical R.A.M. Hopper Assembly Parts ListHopper Additive Feeder Sub-Assembly Optional Typical Additive Feeder Hopper Assembly Parts ListWeigh Hopper Sub-assembly Typical Weigh Hopper Assembly Parts ListSlide Gate Sub-assembly Typical Slidegate Assembly Parts ListKnife Gate Sub-assembly HD Optional Typical Knife Gate below mixer Assembly Parts ListKnife Gate Sub-assembly RD Optional Typical Knife Gate floor stand Assembly Parts ListTypical Mitsubishi Controller Main Parts List Control Panel LayoutBlender Spare Parts Listing Spare Parts KitsProgrammable Settings Addendum Service Supervisor InformationPasswords Metering Test Screen Factory Setup MenuAdvanced Weight Options Screen Feed Algorithm Options Screen Feed Calibration Options ScreenFeeder Setup Mechanical Options ScreenCustomer Setup Menu UnitsTypical Alarm Flags & Feeder Setup Screen Alarm LogFactory Default Setup Parameters Recipe FormatLoadcell Calex Module Dipswitch Settings Mitsubishi Communications Manual General Blender InfoBlender Alarms Inventory Info Recipe Info this is Where YOU Right the NEW Recipe to Recipe Book Manipulation Alarm Number Explanation Fixed Decimal ExplanationUntil the Hopper Feeds Material Into the NEW Batch Parts Department Service Department Sales DepartmentTechnical Assistance Contract Department
Related manuals
Manual 103 pages 37.01 Kb

882.00207.00 specifications

Mitsubishi Electronics has always been at the forefront of innovation in the field of electronics, and one of its significant products is the Mitsubishi Electronics 882.00207.00. This device is designed for enhanced performance and reliability, providing a range of features that cater to both industrial and consumer needs.

One of the main features of the Mitsubishi 882.00207.00 is its robust design, which ensures durability in demanding environments. The device is built to withstand harsh conditions, making it ideal for industrial applications where reliability is critical. Its rugged construction means that it can operate efficiently in extreme temperatures, humidity, and other challenging conditions.

In terms of technology, the Mitsubishi 882.00207.00 incorporates advanced electronic components that enhance its functionality. This includes state-of-the-art processing capabilities that allow for quick data processing and seamless operation. The device’s integration of cutting-edge technology ensures that it meets the performance demands of modern applications while providing energy efficiency.

Another notable characteristic is its user-friendly interface. The device is designed with ease of use in mind, allowing operators to interact with it effortlessly. This ensures that even those with minimal technical expertise can operate the device effectively. The clear display and intuitive controls make it accessible for a wide range of users, facilitating smoother operations in various settings.

The Mitsubishi 882.00207.00 is also equipped with multiple connectivity options. This enables it to integrate seamlessly with other devices and systems, facilitating enhanced communication and data transfer. Whether it’s connecting to existing networks or interfacing with new technologies, the device’s versatility ensures it can adapt to evolving technological landscapes.

Additionally, the device is backed by Mitsubishi's commitment to quality and customer support. Users can expect reliable service and assistance, ensuring that they can maximize the potential of their investment.

In conclusion, the Mitsubishi Electronics 882.00207.00 stands out in the electronics market for its durable construction, advanced technology, user-friendly design, and versatile connectivity options. This makes it an invaluable tool for both industrial applications and everyday consumer use, embodying the innovative spirit that Mitsubishi Electronics is known for.
Top Page Image Contents