Sierra Monitor Corporation HRG010-W, HRG015-W operation manual Disposition of Waste

Page 16

HRX-OM-J049-A

Chapter 1 Safety Instructions

1.7 Disposition of Waste

1.7.1Recovery of refrigerant and compressor oil

The unit belongs to Class 1 in the “Fluorocarbon Recovery and Destruction Law” and uses freon type refrigerant (HFC) and compressor oil. When these fluids need to be recovered, read the instructions below and ensure thorough understanding of them. If you have any questions, contact the local distributor.

Only service personnel or qualified personnel are allowed to open the panel of the unit.

Do not mix the compressor oil with domestic waste for disposition. Also, incineration is permitted only at an authorized incinerator.

Comply with municipal ordinances or regulations to dispose of waste.

The release of refrigerant to atmosphere is banned by law. If the refrigerant needs to be removed, recover it with specific equipment and request a specialized waste disposal agency for disposal of the recovered refrigerant. A person must have proper license to perform refrigerant recovery.

Only personnel with sufficient knowledge and experiences with the unit and associated equipment are allowed to recover refrigerant and compressor oil. The person must have proper license to perform refrigerant recovery.

[Tips]

The type and amount of used freon can be found on the label.

1.7 Disposition of Waste

HRG010-W HRG015-W

1-10

1st edition : Aug. 2006

Rev. A: May. 2007

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Water-refrigerated Thermo cooler To the Customers Table of Contents Error Message and Troubleshooting Chapter Unit MaintenanceStartup and Shutdown Chapter DocumentsTOC-3 TOC-4 Safety Instructions Before Using this UnitLevel of risk Definitions of Serious injury and Minor injury„ Serious injury „ Minor injurySymbols „ High temperature hazards Hazard Warning LabelClassification of risks „ High voltage hazardsType of hazard warning labels Model label Location of hazard warning labelSafety Measures Safety Precautions„ For system transportation, installation and removal Protective equipment„ For handling circulating fluid „ For system operationEmergency Measures Thermo Cooler OFFRecovery of refrigerant and compressor oil Disposition of WasteCirculating fluid disposal Material Safety Data Sheet MsdsSystem disposal Safety Instructions Appearance and Each Section AppearanceName of Each Section 1 HRG010-W2 HRG015-W Name of Each Section HRG015-WControl panel Name FunctionTransport and Installation TransportTransporting with forklift and unit lifting Forklift Insertion Position and Unit LiftingTransporting with caster „ HRG010-W-A / HRG015-W-A caster-mounted optionInstallation Installation conditionsInstallation location Installation location and maintenance work area Recommended Installation LocationInstallation „ Procedure for InstallationHRG010-W-A / HRG015-W-A Caster-mounted Option „ Power supply cable and Gfci breaker Electrical wiringHRG010-W HRG015-W „ How to conduct wiring Removal of Front Panel„ Electrical wiring diagram HRG015-WSpecifications 11 Communication Cable WiringPiping „ How to install piping„ Pipe diameter Name Size HRG010-W HRG015-W „ Recommended piping installationName Qty Supply of circulating fluid Open the supply valve laid with pipesReinstallation of unit „ Disconnection of power supply cableStartup and Shutdown Pre-checkSetting of circulating fluid temperature Power supplyPreparation for startup „ TS switch pump manual operation switch Additional water supplyStarting the unit Unit Startup and ShutdownStopping the unit Check at startup „ Bypass valve„ Bypass relieving valve piping set Error Message Troubleshooting Error MessageTroubleshooting See 5.3 Alarm Reset for error recoveryAlarm Reset Alarm Lamp OFF „ Error checkUndo the screws 6 pcs. to remove the front panel „ When the alarm lamp goes out by performing steps 1. to Location of Reset Switch RS Yellow ButtonRecovery from Power Failure Power Lamp on „ Power error checkUndo the screws 6 pcs. to remove the front panel Switch off the earth leakage breaker once Control of Water Quality Unit MaintenanceSubstances Facility water Circulating fluid spec Spec Inspection and Cleaning Inspection item Daily inspectionInspection method „ Replacement of circulating fluid „ Cleaning of facility waterQuarterly inspection Biannual inspection„ Antifreeze of circulating fluid Check during wintertime„ Antifreeze function automatic pump operation Long-term Storage ConsumablesPart number Qty Remarks Standard Specifications DocumentsHRG010-W HRG015-W Optional Specifications „ Caster„ Gfci breaker „ CommunicationOutline Dimensions 2 HRG010-W-A, HRG015-W-AElectric Circuit 1 HRG010-W, HRG015-W2 HRG010-W-BC, HRG015-W-BC Electric Circuit HRG010-W-BC, HRG015-W-BCFlow Chart „ HRG010-W, HRG015-WThermo Cooler HRG010-W / WRG015-W Daily Inspection Sheet IN/OUTProduct Warranty

HRG015-W, HRG010-W specifications

Sierra Monitor Corporation is renowned for its innovative solutions in the field of industrial monitoring and control. Among its noteworthy offerings are the HRG010-W and HRG015-W wireless gas detectors, specifically designed to enhance safety and efficiency in various industrial environments. These devices provide critical monitoring for hazardous gases, thereby ensuring compliance with safety regulations and creating a safer workplace for employees.

One of the main features of the HRG010-W and HRG015-W models is their advanced sensor technology, which enables accurate detection of hazardous gases, including but not limited to, methane, propane, and hydrogen. This precision is crucial for industries such as oil and gas, wastewater treatment, and chemical manufacturing where the presence of these gases can pose significant risks.

Both models are equipped with powerful wireless communication capabilities. They utilize Zigbee or Wi-Fi technologies to transmit real-time data back to a centralized monitoring system. This feature facilitates instant readings and alerts, allowing for timely interventions and reducing response times during emergencies. Operators can monitor gas levels remotely, thus enhancing operational efficiency and allowing for better resource allocation.

Another important characteristic of the HRG010-W and HRG015-W is their rugged design, tailored to withstand harsh industrial conditions. The enclosures are built with durable materials that resist moisture, dust, and corrosive substances. This durability ensures longevity and reliability in the field, which is paramount for continuous gas detection applications.

Furthermore, these gas detectors are designed with user-friendly interfaces that simplify setup and operation. The built-in display provides clear numerical readings and diagnostic information, while the intuitive controls make it easy for personnel to navigate functions and settings without extensive training.

In addition, both the HRG010-W and HRG015-W models can be integrated with existing control systems and safety measures, creating a comprehensive safety net. This compatibility supports various industry standards and allows facilities to modularly expand their safety networks as needed.

Overall, Sierra Monitor Corporation's HRG010-W and HRG015-W wireless gas detectors epitomize the intersection of technology and safety in industrial environments. With their advanced detection capabilities, robust design, wireless communication, and ease of use, these devices stand out as essential tools for mitigating the risks associated with hazardous gas exposure in a variety of applications.
Top Page Image Contents