Chapter 7 Documents
Chapter 7 Documents
7.1 Standard Specifications
Installation Operating environment
Table 7-1 Standard Specifications (1/2)
Item |
| ||
Rated ambient temp. |
| 32°C (5 to 40°C) | |
Humidity range |
| 45 to 75%RH (No condensation) |
Fluid used | Circulating fluid/fresh water (tap water) or fluids resistant to corrosion of a wetted surface | |
(such as SUS304 and PVC) | ||
|
Input
Rated capacity of tank | 40L | 50L | |
Supply voltage | AC200(50Hz), AC200 to 220V (60Hz) | ||
Recommended earth | 40A, 30mA | 60A, 30mA | |
leakage breaker capacity, | |||
Sensitivity current |
|
| |
Rated power consumption | 3.2/3.8 - 3.8 kW | 4.7/5.8 - 5.8 kW | |
Rated operating current | 12.0/12.5 - 12.5A | 18.0/19.0 – 19.0A | |
Rated consumption | 3.2/3.8 - 3.8 kWh/h | 4.7/5.8 - 5.8kWh/h | |
electric energy | |||
|
|
Output
Display
Facility water
Start/stop command
signal
Rated temp. / accuracy of
circulating fluid
Temp. range of circulating
fluid
Rated cooling capacity
Rated heating capacity
Pumping capacity
Rated flow
Max. flow rate
Output | Op. signal |
|
signal Emergency stop signal
Temperature control
Operation panel
Refrigerant high pressure
gauge
Refrigerant pressure
gauge
Level indicator
Supply temp.: 25°C (5 to 32°C), | Supply temp.: 25°C (5 to 32°C), | |
Flow rate: Max. 33/34L/min, | ||
Flow rate: Max. 38/40L/min, | ||
IN/OUT differential pressure: Max. | ||
IN/OUT differential pressure: Max. 0.25/0.2MPa, | ||
0.25/0.2MPa, | ||
Max. supply press.: 0.3 to 0.4MPa, Exhaust heat: | ||
Max. supply press.: 0.3 to 0.4MPa, Exhaust | ||
heat: Approx. 16W | Approx. 23W | |
|
Remote operation starts upon application of DC24V and 8 mA, and stops at DC0V.
20±1.0°C (only under given load condition)
5 to 35°C
10.0/11.0 kW | 14.5/16.5kW |
(50/60 Hz, 20°C at outlet, 37/49L/min of flow) | (50/60 Hz, 20°C at outlet, 42/54L/min of flow) |
- (1.1kW of pump motor output only) | - (0.75kW of pump motor output only) |
Max. head: 50/50m (50/60Hz, 0/0L/min of flow, 0.49/0.49MPa of supply pressure) | |
37/49L/min | 42/54L/min |
(50/60Hz, 25/25m of the max. head, | (50/60Hz, 25/25m of the max. head, |
0.29/0.33MPa of supply pressure) | 0.28/0.31MPa of supply pressure) |
48/60L/min | 54/65L/min |
(50/60Hz, 0/0m of the max. head, | (50/60Hz, 0/0m of the max. head, |
0.08/0.12MPa of supply pressure) | 0.05/0.09MPa of supply pressure) |
Relay contact ( AC250V of contact capacity, 1A, resistance load. Contact closes during operation,
and contact opens during stop and during
Relay contact (AC250V of contact capacity, 1A, resistance load. Contact closes while alarm light
remains OFF and during
Combined use of temperature control through compressor operation (ON/OFF) and capacity
control through solenoid valve control (ON/OFF)
7segment digital display, capable of display in 0.1°C increments
PV (operating temp.):
Other display lamps: ALARM1 to 3 individual display in the event of an error)
Range:
Range: 0 to 1.0 MPa
SMC
7.1 Standard Specifications | |
1st edition : Aug. 2006 | |
Rev. A: May. 2007 |