Cornelius R-404A REFRIGERANT service manual Control Panel ASS’Y Switches and Displayed Messages

Page 34

OPERATOR’S INSTRUCTIONS

This section describes operating controls and indicators, dispensed product conditions, operating characteris- tics, Unit operation, replenishing syrup supply, product flavor change, checking CO2 supply, operators daily cleaning of Unit, and sanitizing requirements.

CAUTION: Do not place or store anything on top of the Unit.

WARNING: Disconnect electrical power to the Unit to prevent personal injury before attempting any internal maintenance. Only qualified personnel should service internal components or electrical wiring.

NOTE: The No. 1 freeze cylinder (see Figure 5) is the left-hand cylinder facing the front of the Unit. No. 2 freeze cylinder is to the right of No. 1 freeze cylinder.

CONTROL PANEL ASS’Y SWITCHES AND DISPLAYED MESSAGES

CONTROL PANEL ASS’Y SWITCHES

(see Figure 3)

NOTE: The Unit control panel assembly is equipped with a hidden “SECURITY SWITCH” located be- tween “FILL 1” and “ERROR RESET” control switches (see Figure 3). Pressing in and holding “SECURITY SWITCH” for 3 seconds deactivates the control switches preventing tampering with Unit normal operation. To reactivate the control switches, press in and hold the “SECURITY SWITCH” for 3 seconds.

‘‘FILL 1’’ and ‘‘FILL 2’’ Control Switches.

‘‘FILL 1’’ and ‘‘FILL 2’’ control switches, located on control panel assembly, are touch-type switches that require only pressing to activate. ‘‘FILL 1’’ and ‘‘FILL 2’’ control switches are used when filling syrup systems sold-out floats during syrup replenishing, syrup flavor changeover, or sanitizing syrup systems. After syrup systems sold-out floats have been filled, ‘‘FILL 1’’ and ‘‘FILL 2’’ switches may be used to prevent more product entering product blender tanks during BRIX test.

‘‘AUTO BLEND 1’’ and ‘‘AUTO BLEND 2’’ Control Switches.

‘‘AUTO BLEND 1’’ and ‘‘AUTO BLEND 2’’ control switches, located on control panel assembly, are touch-type switches and require only pressing to activate. These switches are used to fill product blender tanks after sold-out floats have been filled using ‘‘FILL 1’’ and ‘‘FILL 2’’ switches. ‘‘AUTO BLEND 1’’ and ‘‘AUTO BLEND 2’’ and ‘‘AUTO 1’’ and ‘‘AUTO 2’’ switches must be pressed to operate freeze cylinders beaters and refrigeration system during normal operation.

‘‘WASH 1’’ and ‘‘WASH 2’’ Control Switches.

‘‘WASH 1’’ and ‘‘WASH 2’’ control switches, located on control panel assembly, are touch-type switches and require only pressing to activate. These switches are used to operate freeze cylinders beaters with no refrigeration during sanitizing.

27

312028000

Image 34
Contents To the Installer Table of Contents Table of Contents cont’d Water Strainer Screen and Double Liquid Check Valve Programming Main Menu Selections Onto Message DisplayVIS Read Actual Viscosity Readout of Product Preparing Unit for SHIPPING, STORING, or RelocatingTroubleshooting Control Panel Switches and Fault Product Carbonation AdjustmentDaily Cleaning of Unit Sanitizing Syrup Systems ‘‘ERROR 1’’ or ‘‘ERROR 2’’ Fault Message Goes on DuringFreeze Cylinder Automatic Defrost Cycle does not Defrost Cycle does not Cancel After Pressing ‘‘CANCELList of Figures Table of Contents cont’d General Description Unit DescriptionTheory of Operation AccessoriesService Tools Generic Flavor TabsManual Defrost System Defrost SystemsAutomatic Defrost System ‘‘SLEEP’’ Sleep Time ‘‘WAKE UP’’ Wake UP TimeFlow Diagram This page Left Blank Intentionally Unpacking and Inspection Identification of LOOSE-SHIPPED PartsSelecting Location Electrical Power RequirementsHZ Unit Installing Drip Tray Supports Item 7 and Item Installing UnitInstalling Leveling Legs Installing Drip Tray Drain Hose KIT ItemInstalling Primary CO2 Regulator Assembly on CO2 Cylinder Connecting CO2 Source Line to Unit CO2 Inlet LineConnecting Electrical Power Circuit to the Unit Connecting City Plain Water Source Line to UnitElectrical BOX Adjusting Product Blender Tanks Secondary CO2 Turning on Electrical Power to UnitAdjusting Primary CO2 Regulator Adjusting Carbonator Secondary CO2 RegulatorHidden Security Switch Message Display Control Panel ASS’YFilling Freeze Cylinders with Product Checking Unit for SYRUP, CO2, or Plain Water LeaksAdjusting Beater Motor Current Either Side Placing Unit in Operating LocationSetting Clock Time of DAY Programming Main Menu Selection Onto Message DisplayMenu Selections Programming ‘‘DEFROST’’ Automatic Settings Into UnitMain Menu Selections DIP Switch Functions Switch FunctionProgramming ‘‘SLEEP’’ Sleep Time Into Unit Programming ‘‘WAKE UP’’ Wake UP Time Into Unit Programming Point of Sale Message DisplayAdjusting VIS SET Product Viscosity of Dispensed Product Master and Relay Circuit Board ‘‘VOLTAGE’’ Displayed Voltage Readout 312028000 Brix Totals Menu Commands DescriptionSyrup Minutes Side Gallons = a X Syrup MinutesDisplayed Error Conditions Programming Proper Refrigerant Type Into Unit ElectronicsDisplayed Error Conditions Control Panel ASS’Y Switches and Displayed Messages Control Panel ASS’Y SwitchesControl Panel Assembly Display Messages ‘‘SECURITY SWITCH.’’Freeze Cylinders Manual or Automatic Defrost Systems Product Sample Valves ‘‘SLEEP’’ Sleep Time OperationFaceplate Relief Valves Product Shutoff ValvesDispensed Product Conditions Syrup Flow RegulatorsDispensing Valves ‘‘OVERRUN’’, AS Applied to Frozen Carbonated BeveragesOperating Unit Operating CharacteristicsReplenishing Syrup Supply Product Flavor Change Cleaning and SanitizingCleaning Condenser Coil Checking CO2 SupplyAdjustments Adjusting ‘‘VIS SET’’ Product Viscosity of Dispensed Product Cleaning CO2 GAS Check Valves TOP Panel Preparing Unit for SHIPPING, STORING, or RelocatingPeriodic Inspection Back PanelOpening Front Access Door Opening and Closing Front Access DoorFront Access Panel Closing Front Access DoorOperating Controls Unit Internal Components SELF-CLOSING Dispensing Valve 312028000 Adjusting Plain Water Pressure Regulator Adjusting Carbonated Water Flow RateFreeze Cylinder Cutaway View Servicing Beater Motor Drive SHAFT/SEAL Assembly Beaters and Scraper Blades Installation Adjusting CO2 Regulators Adjusting Brix WATER-TO-SYRUP ‘‘RATIO’’ of Dispensed Product Daily Cleaning of Unit Product Carbonation AdjustmentSanitizing Syrup Systems To disconnect soft drink tank from Unit syrup system 312028000 Yearly or After Water System Disruption Servicing Carbonator Water Pump Water Strainer ScreenLiquid Check Valve Assembly Servicing Carbonator Water Pump Double Liquid Check ValveReplenishing Syrup Supply Replenishing CO2 Supply Service and Maintenance SectionSyrup Flavor Change Water Strainer Screen and Double Liquid Check Valve Serviced Replacing Freeze Cylinder Beater Drive MotorAdjusting Carbonator Tank Liquid Level Ments in Small IncrementsCarbonator Liquid Level Control Switch Adjustment Refrigeration Flow Diagram Wiring Diagram This page Left Blank Intentionally Troubleshooting Control Panel Switches and Fault Messages ALL Fault Messages not a Control Panel SwitchesPoorly Illuminated Display ONE or More Fault Cannot be Deactivated‘‘H2O OUT’’ Fault Message ALL Fault Message not‘‘CO2 OUT’’ Fault Message Fault Message Goes onTroubleshooting Product Blender Tanks and Carbonator Troubleshooting Dispensed Product Excessively Frozen ProductConsistency Varies FREEZE-UPIllustrated Parts Breakdown Unit Part NumbersOvercounter FCB POST-MIX Dispenser FCB POST-MIX Dispenser FCB POST-MIX Dispenser cont’d Name Secondary CO2 Regulator Components Secondary CO2 Regulator ASS’Y CO2 Regulator Assembly Blender and Tubing Components Tubing Assembly Carb Water Tubing Assembly Water Solenoid to Blender Solenoid Valve Assembly Blender Components Control BOX and Display Panel Components Faceplate Assembly Dispensing Valve Assembly Carbonator Components Carbonator Tank and Linkage Assembly Pump and Motor ASS’Y Beater Motor Drive SHAFT/SEAL ASS’Y Warranty This page Left Blank Intentionally One Cornelius Place Anoka, Minnesota 612 800