Cornelius R-404A REFRIGERANT Hidden Security Switch Message Display, Control Panel ASS’Y

Page 20

STARTING FCB AND ADJUSTING WATER-TO-SYRUP “RATIO” (BRIX) OF DISPENSED PRODUCT

1.Open shutoff valve in city plain water line connected to the Unit. Check for water leaks and tighten or repair

leaks if evident. ‘‘H2O OUT’’ fault message should have gone out but ‘‘SYRUP 1’’, and ‘‘SYRUP 2’’ fault mes- sages will continue to be displayed.

IMPORTANT: Product shutoff valves, located in lines leading from product blender tanks to freeze cylinders (see Figure 2 and 6), must be closed at this time. Closing valves prevents product from filling freeze cylinders while checking BRIX of product in product blender tanks.

2.Close product shutoff valves, located in lines leading from product blender tanks to freeze cylinders, to pre- vent product from entering cylinders.

IMPORTANT: The following CO2 and liquid disconnects disconnecting and connecting procedure for soft drink tank replacement or filling soft drink tank in place must be performed in order as follows:

HIDDEN SECURITY

 

SWITCH

MESSAGE DISPLAY

 

FIGURE 3. CONTROL PANEL ASS’Y

To disconnect soft drink tank from Unit syrup system.

A.Disconnect liquid disconnect from soft drink tank. NOTE – Disconnecting liquid quick disconnect from soft drink tank first prevents syrup from backflowing through Unit syrup flow regulator which may alter regulator adjustment.

B.Second, disconnect CO2 quick disconnect from soft drink tank.

To connect soft drink tank into Unit syrup system.

A.First, connect CO2 quick disconnect to soft drink tank to pressurize the tank.

B.Second, connect liquid quick disconnect to the soft drink tank.

3.Pressurize soft drink tanks containing syrup, then connect tanks into Unit syrup systems.“OFF 1”, “OFF 2”, “SYRUP 1”, and “SYRUP 2” fault messages will continue to be displayed.

4.The following steps A through J are instructions for adjusting the Water-to-Syrup “Ratio” (BRIX) of the dispensed product on one of the systems.

NOTE: The Unit control panel assembly is equipped with a hidden “SECURITY SWITCH” located be- tween “FILL 1” and “ERROR RESET” control switches (see Figure 3). Pressing in and holding the “SECURITY SWITCH” for 3 seconds deactivates the control switches preventing tampering with Unit normal operation. To reactivate the control switches, press in and hold the “SECURITY SWITCH” for 3 seconds.

NOTE: The adjustable carbonated water flow regulators (see Figure 2 and 12) located in their respective systems, control carbonated water flow rate to the product blender tanks. The water flow regulators are factory adjusted at 1.3 ￿ 0.05 oz/second and should not normally require adjustment. If adjustment is necessary, adjust as instructed.

A.Press ‘‘FILL 1’’ switch to fill No. 1 syrup system sold-out float. ‘‘SYRUP 1’’ fault message will go out and ‘‘FILL 1’’ fault message will come on. ‘‘OFF 1’’, ‘‘OFF 2’’, and ‘‘SYRUP 2’’ fault messages will continue to be displayed.

13

312028000

Image 20
Contents To the Installer Table of Contents Table of Contents cont’d Programming Main Menu Selections Onto Message Display VIS Read Actual Viscosity Readout of ProductWater Strainer Screen and Double Liquid Check Valve Preparing Unit for SHIPPING, STORING, or RelocatingProduct Carbonation Adjustment Daily Cleaning of Unit Sanitizing Syrup SystemsTroubleshooting Control Panel Switches and Fault ‘‘ERROR 1’’ or ‘‘ERROR 2’’ Fault Message Goes on DuringList of Figures Defrost Cycle does not Cancel After Pressing ‘‘CANCELFreeze Cylinder Automatic Defrost Cycle does not Table of Contents cont’d General Description Unit DescriptionAccessories Service ToolsTheory of Operation Generic Flavor TabsAutomatic Defrost System Defrost SystemsManual Defrost System ‘‘SLEEP’’ Sleep Time ‘‘WAKE UP’’ Wake UP TimeFlow Diagram This page Left Blank Intentionally Unpacking and Inspection Identification of LOOSE-SHIPPED PartsHZ Unit Electrical Power RequirementsSelecting Location Installing Unit Installing Leveling LegsInstalling Drip Tray Supports Item 7 and Item Installing Drip Tray Drain Hose KIT ItemInstalling Primary CO2 Regulator Assembly on CO2 Cylinder Connecting CO2 Source Line to Unit CO2 Inlet LineElectrical BOX Connecting City Plain Water Source Line to UnitConnecting Electrical Power Circuit to the Unit Turning on Electrical Power to Unit Adjusting Primary CO2 RegulatorAdjusting Product Blender Tanks Secondary CO2 Adjusting Carbonator Secondary CO2 RegulatorHidden Security Switch Message Display Control Panel ASS’YFilling Freeze Cylinders with Product Checking Unit for SYRUP, CO2, or Plain Water LeaksAdjusting Beater Motor Current Either Side Placing Unit in Operating LocationSetting Clock Time of DAY Programming Main Menu Selection Onto Message DisplayMain Menu Selections Programming ‘‘DEFROST’’ Automatic Settings Into UnitMenu Selections Programming ‘‘SLEEP’’ Sleep Time Into Unit Switch FunctionDIP Switch Functions Programming ‘‘WAKE UP’’ Wake UP Time Into Unit Programming Point of Sale Message DisplayAdjusting VIS SET Product Viscosity of Dispensed Product Master and Relay Circuit Board ‘‘VOLTAGE’’ Displayed Voltage Readout 312028000 Totals Menu Commands Description Syrup Minutes SideBrix Gallons = a X Syrup MinutesDisplayed Error Conditions Programming Proper Refrigerant Type Into Unit ElectronicsDisplayed Error Conditions Control Panel ASS’Y Switches and Displayed Messages Control Panel ASS’Y SwitchesControl Panel Assembly Display Messages ‘‘SECURITY SWITCH.’’Freeze Cylinders Manual or Automatic Defrost Systems ‘‘SLEEP’’ Sleep Time Operation Faceplate Relief ValvesProduct Sample Valves Product Shutoff ValvesSyrup Flow Regulators Dispensing ValvesDispensed Product Conditions ‘‘OVERRUN’’, AS Applied to Frozen Carbonated BeveragesReplenishing Syrup Supply Operating CharacteristicsOperating Unit Cleaning and Sanitizing Cleaning Condenser CoilProduct Flavor Change Checking CO2 SupplyAdjustments Adjusting ‘‘VIS SET’’ Product Viscosity of Dispensed Product Cleaning CO2 GAS Check Valves Preparing Unit for SHIPPING, STORING, or Relocating Periodic InspectionTOP Panel Back PanelOpening and Closing Front Access Door Front Access PanelOpening Front Access Door Closing Front Access DoorOperating Controls Unit Internal Components SELF-CLOSING Dispensing Valve 312028000 Adjusting Plain Water Pressure Regulator Adjusting Carbonated Water Flow RateFreeze Cylinder Cutaway View Servicing Beater Motor Drive SHAFT/SEAL Assembly Beaters and Scraper Blades Installation Adjusting CO2 Regulators Adjusting Brix WATER-TO-SYRUP ‘‘RATIO’’ of Dispensed Product Sanitizing Syrup Systems Product Carbonation AdjustmentDaily Cleaning of Unit To disconnect soft drink tank from Unit syrup system 312028000 Yearly or After Water System Disruption Servicing Carbonator Water Pump Water Strainer ScreenLiquid Check Valve Assembly Servicing Carbonator Water Pump Double Liquid Check ValveReplenishing Syrup Supply Syrup Flavor Change Service and Maintenance SectionReplenishing CO2 Supply Water Strainer Screen and Double Liquid Check Valve Serviced Replacing Freeze Cylinder Beater Drive MotorAdjusting Carbonator Tank Liquid Level Ments in Small IncrementsCarbonator Liquid Level Control Switch Adjustment Refrigeration Flow Diagram Wiring Diagram This page Left Blank Intentionally Troubleshooting Control Panel Switches and Fault Messages Control Panel Switches Poorly Illuminated Display ONE or More FaultALL Fault Messages not a Cannot be DeactivatedALL Fault Message not ‘‘CO2 OUT’’ Fault Message‘‘H2O OUT’’ Fault Message Fault Message Goes onTroubleshooting Product Blender Tanks and Carbonator Troubleshooting Dispensed Product Frozen Product Consistency VariesExcessively FREEZE-UPIllustrated Parts Breakdown Unit Part NumbersOvercounter FCB POST-MIX Dispenser FCB POST-MIX Dispenser FCB POST-MIX Dispenser cont’d Name Secondary CO2 Regulator Components Secondary CO2 Regulator ASS’Y CO2 Regulator Assembly Blender and Tubing Components Tubing Assembly Carb Water Tubing Assembly Water Solenoid to Blender Solenoid Valve Assembly Blender Components Control BOX and Display Panel Components Faceplate Assembly Dispensing Valve Assembly Carbonator Components Carbonator Tank and Linkage Assembly Pump and Motor ASS’Y Beater Motor Drive SHAFT/SEAL ASS’Y Warranty This page Left Blank Intentionally One Cornelius Place Anoka, Minnesota 612 800