Cornelius R-404A REFRIGERANT service manual Beaters and Scraper Blades Installation

Page 53

BEATER

Key on End

of PostKey on End of Post

Key Slot on Blade

Scraper blades must be mounted to the beater body as shown using the perforated edge as the leading edge. Line up key on end of posts with key slot in scraper blades.

FIGURE 10. BEATERS AND SCRAPER BLADES INSTALLATION

1.Press applicable ‘‘OFF 1’’ or ‘‘OFF 2’’ switch to prevent more product from entering the applicable product blender tank.

2.Disconnect Unit syrup inlet line from the applicable soft drink tank.

3.Using a flat blade screwdriver, turn lock counterclockwise to unlock the front access door (see Figure 5), then open the door.

4.Remove lower front access panel as instructed for access to the applicable carbonated water flow regula- tor, product shutoff valve, and the product sample valve.

5.Close applicable product shutoff valve to prevent more product from entering the freeze cylinder.

6.Place container under applicable product sample valve. Open the valve and allow all product to be purged from the product blender tank, then close the valve.

7.Note pressure setting on the applicable secondary CO2 regulator with 60-psi gauge for the applicable prod- uct blender tank. Turn regulator adjusting screw out (counterclockwise) until gauge reads 0-psi. Pull up on the applicable product blender tank relief valve to release CO2 pressure from the tank.

8.Disconnect carbonated water line from the outlet side of the applicable carbonated water flow regulator.

9.Connect line, long enough to reach to the outside of the Unit, to the water flow regulator outlet, then route the line to the outside of the Unit.

10. Place end of the carbonated water line, routed to the outside of the Unit, in the container.

312028000

46

Image 53

Contents To the Installer Table of Contents Table of Contents cont’d VIS Read Actual Viscosity Readout of Product Programming Main Menu Selections Onto Message DisplayWater Strainer Screen and Double Liquid Check Valve Preparing Unit for SHIPPING, STORING, or RelocatingDaily Cleaning of Unit Sanitizing Syrup Systems Product Carbonation AdjustmentTroubleshooting Control Panel Switches and Fault ‘‘ERROR 1’’ or ‘‘ERROR 2’’ Fault Message Goes on DuringList of Figures Defrost Cycle does not Cancel After Pressing ‘‘CANCELFreeze Cylinder Automatic Defrost Cycle does not Table of Contents cont’d Unit Description General DescriptionService Tools AccessoriesTheory of Operation Generic Flavor TabsAutomatic Defrost System Defrost SystemsManual Defrost System ‘‘WAKE UP’’ Wake UP Time ‘‘SLEEP’’ Sleep TimeFlow Diagram This page Left Blank Intentionally Identification of LOOSE-SHIPPED Parts Unpacking and InspectionHZ Unit Electrical Power RequirementsSelecting Location Installing Leveling Legs Installing UnitInstalling Drip Tray Supports Item 7 and Item Installing Drip Tray Drain Hose KIT ItemConnecting CO2 Source Line to Unit CO2 Inlet Line Installing Primary CO2 Regulator Assembly on CO2 CylinderElectrical BOX Connecting City Plain Water Source Line to UnitConnecting Electrical Power Circuit to the Unit Adjusting Primary CO2 Regulator Turning on Electrical Power to UnitAdjusting Product Blender Tanks Secondary CO2 Adjusting Carbonator Secondary CO2 RegulatorControl Panel ASS’Y Hidden Security Switch Message DisplayChecking Unit for SYRUP, CO2, or Plain Water Leaks Filling Freeze Cylinders with ProductPlacing Unit in Operating Location Adjusting Beater Motor Current Either SideProgramming Main Menu Selection Onto Message Display Setting Clock Time of DAYMain Menu Selections Programming ‘‘DEFROST’’ Automatic Settings Into UnitMenu Selections Programming ‘‘SLEEP’’ Sleep Time Into Unit Switch FunctionDIP Switch Functions Programming Point of Sale Message Display Programming ‘‘WAKE UP’’ Wake UP Time Into UnitAdjusting VIS SET Product Viscosity of Dispensed Product Master and Relay Circuit Board ‘‘VOLTAGE’’ Displayed Voltage Readout 312028000 Syrup Minutes Side Totals Menu Commands DescriptionBrix Gallons = a X Syrup MinutesProgramming Proper Refrigerant Type Into Unit Electronics Displayed Error ConditionsDisplayed Error Conditions Control Panel ASS’Y Switches Control Panel ASS’Y Switches and Displayed Messages‘‘SECURITY SWITCH.’’ Control Panel Assembly Display MessagesFreeze Cylinders Manual or Automatic Defrost Systems Faceplate Relief Valves ‘‘SLEEP’’ Sleep Time OperationProduct Sample Valves Product Shutoff ValvesDispensing Valves Syrup Flow RegulatorsDispensed Product Conditions ‘‘OVERRUN’’, AS Applied to Frozen Carbonated BeveragesReplenishing Syrup Supply Operating CharacteristicsOperating Unit Cleaning Condenser Coil Cleaning and SanitizingProduct Flavor Change Checking CO2 SupplyAdjustments Adjusting ‘‘VIS SET’’ Product Viscosity of Dispensed Product Cleaning CO2 GAS Check Valves Periodic Inspection Preparing Unit for SHIPPING, STORING, or RelocatingTOP Panel Back PanelFront Access Panel Opening and Closing Front Access DoorOpening Front Access Door Closing Front Access DoorOperating Controls Unit Internal Components SELF-CLOSING Dispensing Valve 312028000 Adjusting Carbonated Water Flow Rate Adjusting Plain Water Pressure RegulatorFreeze Cylinder Cutaway View Servicing Beater Motor Drive SHAFT/SEAL Assembly Beaters and Scraper Blades Installation Adjusting CO2 Regulators Adjusting Brix WATER-TO-SYRUP ‘‘RATIO’’ of Dispensed Product Sanitizing Syrup Systems Product Carbonation AdjustmentDaily Cleaning of Unit To disconnect soft drink tank from Unit syrup system 312028000 Servicing Carbonator Water Pump Water Strainer Screen Yearly or After Water System DisruptionServicing Carbonator Water Pump Double Liquid Check Valve Liquid Check Valve AssemblyReplenishing Syrup Supply Syrup Flavor Change Service and Maintenance SectionReplenishing CO2 Supply Water Strainer Screen and Double Liquid Check Valve Replacing Freeze Cylinder Beater Drive Motor ServicedMents in Small Increments Adjusting Carbonator Tank Liquid LevelCarbonator Liquid Level Control Switch Adjustment Refrigeration Flow Diagram Wiring Diagram This page Left Blank Intentionally Troubleshooting Control Panel Switches and Fault Messages Poorly Illuminated Display ONE or More Fault Control Panel SwitchesALL Fault Messages not a Cannot be Deactivated‘‘CO2 OUT’’ Fault Message ALL Fault Message not‘‘H2O OUT’’ Fault Message Fault Message Goes onTroubleshooting Product Blender Tanks and Carbonator Troubleshooting Dispensed Product Consistency Varies Frozen ProductExcessively FREEZE-UPUnit Part Numbers Illustrated Parts BreakdownOvercounter FCB POST-MIX Dispenser FCB POST-MIX Dispenser FCB POST-MIX Dispenser cont’d Name Secondary CO2 Regulator Components Secondary CO2 Regulator ASS’Y CO2 Regulator Assembly Blender and Tubing Components Tubing Assembly Carb Water Tubing Assembly Water Solenoid to Blender Solenoid Valve Assembly Blender Components Control BOX and Display Panel Components Faceplate Assembly Dispensing Valve Assembly Carbonator Components Carbonator Tank and Linkage Assembly Pump and Motor ASS’Y Beater Motor Drive SHAFT/SEAL ASS’Y Warranty This page Left Blank Intentionally One Cornelius Place Anoka, Minnesota 612 800