Hearth and Home Technologies VRT-BZ-B-CE manual 7Electrical Information, Ignition System Wiring

Page 23

7Electrical Information

A. Ignition System Wiring

•This gas stove is equipped with an electronic ignition system which operates on a 6 volt system.

•The batteries are located within the ignition module which is located behind the glass door assembly. A wiring diagram is shown in Figure 7.1.

•The battery pack requires four AA batteries (not included).

CAUTION

Battery polarity must be correct or module damage will occur.

WARNING

Shock Risk

•Replace damaged wire with type 105° C rated wire.

•Wire must have high temperature insulation.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

	FLAME SPARKER/
	SENSOR	VALVE
	PILOT
	IGNITION MODULE	REMOTE
	IGNITION MODULE	CONTROL
	6VDC	ANT.
		ON/OFF
		WALL SWITCH
		IGNITION
		MODULE
		(6V)
	BATTERY PORT
	(4 AA BATTERIES)
		THERMOCOUPLE
		BLOCK
	ON/OFF	(CONNECTED TO
	ON/OFF	BACK OF VALVE)
	SWITCH	BACK OF VALVE)
	SWITCH
		VALVE
	PILOT GAS LINE
	CONNECTED TO
	BACK OF VALVE
	Figure 7.1 Electronic Ignition Wiring Diagram
	Heat & Glo • VRTIKL-CE • 7031-292 Rev E • 12/07	23

Image 23

Contents Do Discardnot What to do if you smell gasDo not Discard this Manual Serial No Model Name Test Lab Report No Manufactured DateTable of Contents Combustible Materials 1Listing and Code ApprovalsAppliance Certiﬁcation Non-Combustible MaterialsInspect Appliance & Components Design & Installation ConsiderationsGetting Started 15.2 25.7 30.8 137.2 91.4 78.1 33.7 39.4 3Appliance Location and ClearancesSelecting Appliance Location Clearances to Combustibles10.2 78.1 91.4 Optional Stone Surround InstalledFlue Termination Minimum Clearances 4Termination LocationsGas stove Alcove ApplicationsMeasuring Standards Flue InformationFlue Components Use of ElbowsFor Natural, Propane and Butane Gases Flueing DiagramsNatural Gas One 90 0 Elbow System Natural Gas Two 90 0 Elbows System Min H1 Max H1 + H2 Max Natural Gas Two 900 Elbows System V1 Min Max Natural Gas Three 90 0 Elbows System Step Horizontal TerminationBefore YOU Begin Slim Line Wall ThimbleFIG. B Minimum Clearance Balance Flue Pipe Vertical TerminationSecure Flashing with NON-HARDENING Sealant Roofing Nails Twist-lock the flue cap and seal Vertical Flue RestrictorCheck for GAS Leaks Gas InformationGas Pressure Requirements Gas Connection Shock Risk Ignition System Wiring7Electrical Information Leveling and Bolting Down the Appliance Appliance SetupRemove Shipping Materials Unbolting Appliance from the PalletOn TOP of Appliance AccessoriesTop to Rear Flue Conversion On Back of Appliance Installing the BafﬂePlacing Mineral Wool Positioning the LogsCap and Barrel Fastener System Before Lighting Appliance Operating InstructionsDo not Connect 240 VAC to the Control Valve Lighting the ApplianceAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure After servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks Maintenance TasksElectronic Ignition System TroubleshootingSymptom Possible Causes Corrective Actions 47.9 104.5 103.5 40.3 18.1 76.2 73.3 86.7 Appliance Dimension DiagramReference Materials 75.3 62.0 76.8 42.8 86.7 112.6 Appliance Dimension with Stone Surround DiagramSL-09D SL-12/17D SL-24D SL-36D SL-48D Flue Components DiagramTermination Kits Flue Components ListComponents Log Set Assembly Service PartsP2B/B2P-VRT-CE Description Serial # Part NumberValve Assembly REM-DLX-CE Warranty Policy Heat & GLO Limited 10 Year WarrantyContact Information Your Records for Model