Jura Capresso Z5 manual Solvent in Tank Press Button, Machine is Decalcifying

Page 34

Once started, the decalcifying program must not be inter- rupted.

Always wait until the decalcifying agent has been used up and the tank is empty. Never fill in additional descaling agent.

COFFEE READY

DESCALE

Press the maintenance key (C).

TRAY / GROUNDS

EMPTY

Empty the drip tray (1) and the coffee grounds tray with the container (3).

TRAY

MISSING

Place the empty, clean drip tray (1) and the coffee grounds tray with the container (3) back into the IMPRESSA Z5.

SOLVENT IN TANK

PRESS BUTTON

Remove the water tank from the machine. Empty out any remaining water.

Completely dissolve the content of one blister (3 tablets) in a receptacle containing 0.6 litres of water, and pour the mixture into the water tank. Place the water tank back into the machine.

SOLVENT IN TANK

PRESS BUTTON

Remove the cappuccino nozzle (4) from the machine (Fig. 14).

Place a receptacle each under the height-adjustable hot water spout (12) and under the connecting parts of the nozzle (use tall receptacle). Press the maintenance key (C).

MACHINE IS DECALCIFYING

You will hear an acoustic signal.

TRAY / GROUNDS

EMPTY

Empty the drip tray (1) and the coffee grounds tray with the con- tainer (3).

TRAY

MISSING

Place the empty, clean drip tray (1) and the coffee grounds tray with the container (3) back into the IMPRESSA.

WATER TANK

FILL

Thouroughly rinse out the water tank and fill it with fresh cold tap water. Then place it back into the IMPRESSA.

PRESS BUTTON

Re-assemble the cappuccino nozzle.

Place a cup each under the height-adjustable hot water spout (12) and the cappuccino nozzle (4), and press the maintenance key (C).

MACHINE IS DECALCIFYING

UNIT IS HEATING

After the machine has heated up, it will automatically perform a rinsing cycle.

RINSING

34

Image 34

Contents Impressa Z5 Jura Elektroapparate AG, CH-4626 Niederbuchsiten Correct assembly of the cappuccino nozzle F G H I J K L M Description of the machine Contents Introduction Safety information 1.1 WarningPrecautions Preparing the Impressa Z5 2.1 Check supply voltageFill water tank Adjusting the grinding gearCheck electrical fuse Fill coffee beansStainless steel vacuum milk container 16b Power switchFirst use Adjusting your machine to the water hardness Cup illuminationUsing the Claris plus filter cartridge Installing the filter Unit is Heating Coffee Ready Changing the filter Filter Rins Coffee Ready FILTER-CHANGEMaking special coffee Rinsing the machineMaking coffee Espresso, 2 espressos, 1 coffee, 2 coffees Rinsing Coffee Ready Cappuccino Milk Cappuccino Making cappuccinoCappuccino rinsing cycle CappuccinoCappuccino cleaning cycle Making hot milk Cleaning the cappuccino nozzle Machine is Cleaning Coffee Ready Making hot waterBrewing coffee using pre-ground coffee powder Switching the Impressa off Rinse Left Spout Press Button Cappuccino setting Goodbye Enough ? Press ButtonSetting the amount of hot water Milk setting Enough Water Press Button Programming the filter MaintenanceProgramming Rinse UnitProgramming the coffee strength Cappuccino programming Programming the milkSave energy Save energy Level Setting the timeSave energy No Time Unit on Programming the automatic switch-on timeProgramming the automatic switch-off time Unit on Minutes Information Information OFF After 1 EspressoRenaming Programming the display Programming the languageChanging the units Maintenance Filling the water tank Changing the time formatDrip tray missing Emptying the coffee groundsEmptying the drip tray Grounds container missingAroma preservation cover missing Information about cleaning cycleFilling the bean tank Removing stones from the grinding gearInformation about decalcify CleaningEmptying the system Tray / Grounds Empty Machine is CleaningDecalcifying ADD Tablet Machine is Decalcifying Solvent in Tank Press Button Machine is Decalcifying Unit is Heating Disposal Tips for perfect coffeeProblems Problem Cause RemedyTechnical data Legal information