Jura Capresso Z5 manual Programming the filter, Maintenance, Rinse Unit

Page 20

15. Programming

The IMPRESSA leaves the factory with a number of default settings that allow you to make coffee without having to pro- gram the machine first. You can, however, adjust various parameters to make the coffee suit your personal taste.

The following parameters can be programmed:

Filter

Water hardness

Maintenance

Temperature

Coffee strength

Cappuccino

Milk

Save energy

Time

Automatic switch-on time

Automatic switch-off time

Information

Rename

Language

Display

15.1 Programming the filter

Please refer to Chapter 5 “Using the CLARIS plus filter cartridge”.

15.2Programming your machine to the correct water hardness (only with FILTER NO)

Please refer to Chapter 4 “Adjusting your machine to the water hardness”.

15.3 Maintenance

You can activate the following maintenance functions from this program item:

RINSING MACHINE, CLEAN CAPPUCCINO,

CHANGE FILTER, CLEAN UNIT, RINSE CAPPUCCINO, DECALCIFY MACHINE.

“DECALCIFY MACHINE” is not displayed if you are using a CLARIS plus filter and the filter is set to “Yes”.

“CHANGE FILTER” is not displayed if you are not using a CLARIS plus filter and the filter is set to “No”.

COFFEE READY

Press the Rotary Switch (B) until you hear an acoustic signal.

FILTER

NO or YES

Turn the Rotary Switch (B) until the following message is dis- played:

MAINTENANCE

Press the Rotary Switch (B) to start programming.

RINSE UNIT

Turn the Rotary Switch (B) until the required maintenance func- tion (for selection see above) is displayed. Press the Rotary Switch (B) to activate the function.

15.4Programming the temperature for coffee, espresso, cappuccino and special coffee

You can adjust the temperature for each type of coffee sepa- rately. The temperature can be set to 3 different levels (LOW, NORMAL, HIGH).

20

Image 20

Contents Impressa Z5 Jura Elektroapparate AG, CH-4626 Niederbuchsiten Correct assembly of the cappuccino nozzle F G H I J K L M Description of the machine Contents Safety information 1.1 Warning PrecautionsIntroduction Preparing the Impressa Z5 2.1 Check supply voltageAdjusting the grinding gear Check electrical fuseFill water tank Fill coffee beansFirst use Power switchStainless steel vacuum milk container 16b Adjusting your machine to the water hardness Cup illuminationUsing the Claris plus filter cartridge Installing the filterChanging the filter Filter Rins Unit is Heating Coffee Ready Coffee Ready FILTER-CHANGERinsing the machine Making coffee Espresso, 2 espressos, 1 coffee, 2 coffeesMaking special coffee Rinsing Coffee ReadyCappuccino Making cappuccino Cappuccino rinsing cycle Cappuccino Milk CappuccinoCappuccino cleaning cycle Cleaning the cappuccino nozzle Machine is Cleaning Coffee ReadyMaking hot milk Making hot waterBrewing coffee using pre-ground coffee powder Switching the Impressa offCappuccino setting Goodbye Rinse Left Spout Press Button Enough ? Press Button Enough Water Press Button Milk settingSetting the amount of hot water Maintenance ProgrammingProgramming the filter Rinse UnitProgramming the coffee strength Cappuccino programming Programming the milkSave energy Setting the time Save energy NoSave energy Level TimeProgramming the automatic switch-on time Programming the automatic switch-off time Unit on Unit on MinutesInformation OFF After Information 1 EspressoRenaming Changing the units Programming the languageProgramming the display Maintenance Filling the water tank Changing the time formatEmptying the coffee grounds Emptying the drip trayDrip tray missing Grounds container missingInformation about cleaning cycle Filling the bean tankAroma preservation cover missing Removing stones from the grinding gearEmptying the system CleaningInformation about decalcify Machine is Cleaning Decalcifying Tray / Grounds Empty ADD Tablet Machine is Decalcifying Unit is Heating Solvent in Tank Press Button Machine is Decalcifying Disposal Tips for perfect coffeeProblems Problem Cause RemedyTechnical data Legal information