Nilfisk-Advance America SR 1100S B manual Machine Operation, Hopper Emptying, After Machine USE

Page 65

USER MANUAL

ENGLISH

MACHINE OPERATION

WARNING!

Pay careful attention when operating the machine at high speed: sudden steering could cause this three-wheel machine to become unstable due to weight distribution.

Always reduce the speed before steering.

1.Avoid stopping for a long time with the machine in the same position and the brooms turning: this could create unwanted marks on the fl oor.

2.To collect light and bulky waste materials, lift the front skirt by pressing the pedal (5); take into consideration that the machine vacuum capability is reduced when the front skirt is lifted.

CAUTION!

When operating on wet grounds, it is essential to turn off the vacuum system with the lever (79) to prevent the dust filter from being damaged.

3.For machine proper operation, the dust fi lter must be as clean as possible. To clean it while sweeping, turn on the fi lter shaker by pressing the switch (79) forward for a few seconds.

During this operation the vacuum fan is automatically shut off.

After cleaning the fi lter, press the switch (79) backward to restart the vacuum system; then start sweeping again.

While working, repeat the procedure every 10 minutes on average (depending on the dustiness of the area to be cleaned).

NOTE

When the dust fi lter is clogged and/or the hopper is full, the machine cannot collect dust and debris anymore.

4.The hopper (17) should be dumped after each working period and whenever it is full (see the procedure in the next paragraph).

HOPPER EMPTYING

1.Stop the machine by releasing the drive pedal.

2.Turn the ignition key (2) to "0".

3.Engage the parking brake by pressing the pedal (3) and engaging the lever (4).

4.Disengage the hook (18) by pulling its lower end.

5.Remove the hopper (17) by using the handle (19) and by disengaging it from the inner guides.

Discharge all the debris into special containers. To make discharging procedure easier, inside the hopper there are two different containers (optional) with handle (36).

6.Install the containers with handle (36), if equipped.

7.Install the hopper (17) and engage it to the inner guides, then fasten it with the hook (18).

8.The machine is ready to start working again.

AFTER MACHINE USE

After working, before leaving the machine, perform the following procedures.

1.Lift the side brooms with the lever (85).

2.Lift the main broom with the lever (86).

3.Turn on the fi lter shaker with the switch (79).

4.Empty the hopper (17) (see the procedure in the previous paragraph).

5.Remove the ignition key (72).

6.Engage the parking brake by pressing the pedal (3) and engaging the lever (4).

PUSHING/TOWING THE MACHINE

To push/tow the machine when it is turned off, no special prearrangement is necessary.

MACHINE LONG INACTIVITY

If the machine is not going to be used for more than 30 days, proceed as follows:

1.Check that the machine storage area is dry and clean.

2.Disconnect the battery connector (46).

FIRST PERIOD OF USE

After the fi rst 8 hours perform the following procedures:

–Check the fastening and connecting parts for proper tightening.

–Check the visible parts for integrity and leakages.

SR 1100S B

146 2494 000(2)2007-02 A

15

Page 64 Page 66
Image 65
Page 64 Page 66
Contents 146 2494 00022007-02 a Sweeper SR 1100S BSR 1100S B SweeperEinleitung InhaltsverzeichnisEinleitung AUSPACKEN/AUSLIEFERUNG Allgemeine Hinweise Benutzte SymboleSicherheit Betriebsanleitung Deutsch Maschinenaufbau Maschinenbeschreibung4341 4750 Maschinenaufbau fortgesetztZUBEHÖRE/OPTIONEN Schalttafel UND BedienelementeAllgemein Werte Technische DatenLeistungen Werte Batterien WerteFarbencodes SchaltplanSchaltplan fortgesetzt PRÜFUNG/VORBEREITUNG DER Batterien AN Einer Neuen Maschine BetriebEinstellung des Ladegeräts VOR DEM Anlassen DER MaschineMaschineneinstellung Maschinenabstellen Maschinenanlassen UND -ABSTELLENMaschinenanlassen Entleerung DES Abfallbehälters Maschine in BetriebNach DER Maschinenbenutzung SCHUB-/SCHLEPPBEWEGUNG DER MaschineÜbersichtstabelle DER Planmässigen Wartung WartungVorgang Bei Auslieferung AllePrüfung UND Einstellung DER Hauptkehrwalzenhöhe Die entsprechende Nabe a eingefügt wird Ersetzen DER HauptkehrwalzeErsetzung DER Seitenbesen Prüfung UND Einstellung DER SeitenbesenhöheReinigung UND Vollständigkeitsprüfung Desb C E Staubfilters Prüfung der Vorder- und Hinterflaps Prüfung DER Flapshöhe UND FunktionsfähigkeitPrüfung der Seitenflaps Batterieladung durch externes Ladegerät Option BatterieladungBatterieladung durch externes Ladegerät Prüfung/Ersetzung der Flachsicherungen PRÜFUNG/ERSETZUNG/RÜCKSCHALTUNG DER SicherungenPrüfung der rückschaltbaren Sicherungen EinbauFehler Mögliche Ursache Lösung FehlersucheVerschrottung Introduction Table DES MatieresIntroduction Deballage / Livraison Instructions Generales Symboles UtilisesSecurite Manuel Dutilisation Français Structure DE LA Machine Description DE LA MachineStructure DE LA Machine suite Accessoires / Options Tableau DE Bord ET CommandesCaractéristiques générales Valeurs Caracteristiques TechniquesPerformances Valeurs Batteries ValeursCodes des couleurs Schema ElectriqueLégende Schema Electrique suite Controle / Preparation DES Batteries SUR UNE Machine Neuve UtilisationAvant LA Mise EN Marche Configuration DU Type DE Batteries Installees WET OU GELConfiguration de la machine Configuration du chargeur de batterieArrêt de la machine Mise EN Marche ET Arret DE LA MachineMise en marche de la machine Machine AU Travail Deplacement PAR Poussee / Remorquage DE LA MachineVidange DU Conteneur Dechets Apres Lutilisation DE LA MachinePlan Dentretien Programme EntretienControle ET Reglage DE LA Hauteur DU Balai Central Remplacement DU Balai Central Controle ET Reglage DE LA Hauteur DES Balais Lateraux Remplacement DES Balais LaterauxNettoyage ET Controle DE Lintegrite DU Filtre a Poussiere Contrôle des volets avant et arrière Controle DE LA Hauteur ET DU Fonctionnement DES VoletsContrôle des volets latéraux Chargement des batteries avec chargeur de batterie externe Chargement DES BatteriesContrôle / remplacement des fusibles à lamelle Controle / Remplacement Retablissement DES FusiblesContrôle des fusibles restaurables ReposeProblème Cause probable Remède Depistage DES PannesMise EN Decharge Table of Contents HOW to Keep this Manual Declaration of Conformity Manual Purpose and ContentsTarget Identification DataUNPACKING/DELIVERY Spare Parts and MaintenanceOther Reference Manuals Changes and ImprovementsGeneral Instructions SafetySymbols English Machine Structure Machine DescriptionMachine Structure Continues Control Panel ACCESSORIES/OPTIONSGeneral Values Technical DataPerformance Values Batteries ValuesColour code Wiring DiagramKey Wiring Diagram Continues USE Battery CHECK/SETTING on a NEW MachineMachine setting WET or GEL Battery SettingBattery charger setting Before Starting the MachineStopping the machine Starting and Stopping the MachineStarting the machine Hopper Emptying Machine OperationAfter Machine USE PUSHING/TOWING the MachineScheduled Maintenance Table MaintenanceProcedure Upon delivery 200 400Main Broom Height Check Adjustment Main Broom Replacement Side Broom Replacement Side Broom Height Check AdjustmentDust Filter Cleaning and Integrity Check Front and rear skirt check Skirt Height and Operation CheckSide skirt check Charging the batteries with the battery charger optional Battery ChargingCharging the batteries with an external battery charger Lamellar fuse check/replacement Fuse CHECK/REPLACEMENT/RESETAssembly Circuit breaker checkTrouble Possible cause Remedy TroubleshootingScrapping Inleiding InhoudsopgaveInleiding Verpakking VERWIJDEREN/AFLEVERING Algemene Instructies Gebruikte SymbolenVeiligheid Gebruiksaanwijzing Nederlands Bouw VAN DE Machine Beschrijving VAN DE MachineOpbouw VAN DE Machine vervolg Bedieningspaneel EN Knoppen Accessoires / OptiesAlgemeen Waarden Technische EigenschappenPrestaties Waarden Accus WaardenKleurcodering Elektrisch SchemaElektrische Installatie vervolg Controle / Voorbereidingen Voor Accus OP EEN Nieuwe Machine GebruikVoor HET Starten VAN DE Machine Instelling VAN HET Type Gemonteerde Accu WET of GELAfstelling van de machine De acculader instellenDe machine stoppen DE Machine Starten EN StoppenStarten van de machine DE Afvalcontainer Legen Machine in BedrijfNA Gebruik VAN DE Machine DUW-/TREKBEWEGING VAN DE MachineOnderhoud OnderhoudsschemaProcedure Bij aflevering DE Hoogte VAN DE Hoofdborstel Controleren EN Afstellen DE Hoofdborstelvervangen DE Zijborstels Vervangen DE Hoogte VAN DE Zijborstels Controleren EN AfstellenReiniging EN Contole OP Integriteit VAN HET Stoffilter Controle van de voor- en achterflap Controle VAN DE Hoogte EN Werking VAN DE FlapsControle van de zijflaps Accu’s met externe acculader opladen optioneel ACCU’S OpladenAccu’s met externe acculader opladen Controle/vervanging van de smeltzekeringen Controle / Vervanging / Resetten VAN DE ZekeringenControle van de herbruikbare zekeringen MontageProbleem Waarschijnlijke oorzaak Oplossing Storingen LokaliserenVerwijdering

SR 1100S B specifications

The Nilfisk-Advance America SR 1100S B is a versatile and efficient scrubber dryer that enhances cleaning operations in a variety of settings. Known for its robust design and user-friendly features, this machine is ideal for both small and large facilities, including warehouses, retail spaces, and industrial environments.

One of the main features of the SR 1100S B is its compact and ergonomic design, which allows for easy maneuverability in tight spaces. This enables cleaning staff to efficiently scrub floors without the hassle of navigating bulky equipment. With a cleaning width of 28 inches, it provides effective coverage while ensuring ease of use.

Powered by a durable battery system, the SR 1100S B allows for cord-free operation, adding to its convenience. The model is equipped with an auto-fill feature that simplifies the refilling of the solution tank, saving time in busy environments where every minute counts. The large solution and recovery tanks minimize downtime by reducing the frequency of refills and disposals during cleaning tasks.

The scrubber dryer utilizes advanced motor technology, offering powerful suction and scrubbing capabilities. Its high-performance brushes deliver superior results, effectively removing dirt and grime from different types of flooring, including tile, vinyl, and concrete. The machine also features adjustable down pressure settings, allowing operators to customize performance based on the specific cleaning needs of the surface being treated.

An intuitive control panel enhances user experience, featuring easy-to-read indicators for battery status and operational settings. The SR 1100S B is designed with safety in mind, incorporating user-friendly controls and configurations that reduce the risk of accidents during operation.

Another notable characteristic is the unit's ability to operate with eco-friendly cleaning solutions, promoting a more sustainable approach in daily cleaning tasks. This makes it an excellent choice for green cleaning initiatives, as it minimizes environmental impact while maintaining high cleaning standards.

In summary, the Nilfisk-Advance America SR 1100S B combines efficiency, convenience, and advanced technology. Its compact design, powerful performance, and ease of use make it a valuable tool for anyone seeking to achieve optimal cleanliness in various institutional and commercial settings. Whether for daily maintenance or deep cleaning efforts, this scrubber dryer stands out as a reliable solution for modern cleaning challenges.
Top Page Image Contents