Woods Equipment S30CD manual Advertencia, Be Careful

Page 12
50530315-A

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

(Safety Decals continued from previous page)

11 - PN 50530707

12 - PN 50530728

WARNING

ADVERTENCIA

HIGH-PRESSURE FLUID HAZARD

To prevent serious injury or death:

1. Relieve pressure on system before repairing, adjusting, or disconnecting.

2. Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands.

3. Keep all components in good repair.

PELIGRO DE FLUIDO BAJO

ALTA PRESION

Para evitar heridas graves o la muerte:

1. Alivie la presión del sistema antes de hacer repara ciones, ajustes o desconecciones.

2. Use protección apropiada en las manos y en los ojos, cuando revise para ver si hay fugas. Utilice una tabla o un cartón en vez de las manos.

3. Mantenga todos los componentes en buen estado.

14 - PN 50530315

16 - PN 33347

DANGER

￿￿￿￿

￿￿

15 - PN 18864

￿￿￿￿￿￿

ROTATING DRIVELINE

 

CONTACT CAN CAUSE DEATH

KEEP AWAY!

 

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

DO NOT OPERATE WITHOUT -

￿ All driveline guards, tractor and

 

equipment shields in place

 

￿ Drivelines securely attached at both ends

￿ Driveline guards that turn freely on

 

￿￿￿￿￿￿33347E

driveline

18864-C

 

 

 

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

12 Safety

MAN0943 (07/12/2011)

 

 

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Flail Shredder Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications Balance Statement General InformationSafety Safety RulesPreparation TrainingTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation OperationPrincipal Components BREAK-IN of the Flail ShredderHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Point HitchLoad Sensing Hydraulics 3-Point Models Only Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Without Quick Hitch Attachment Removing Shredder from TractorRubber Flaps or Belting Preparing for OperationFlail Knives Flail HeightSetting Flail Height Setting Caster WheelsStarting the Shredder Cleaning Stopping the ShredderHazard Area Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Service & Maintenance Service & MaintenanceLubricants GreasingDaily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation Figure AnnuallyLubrication Service Record Hours Serviced by Hours or dailyHours Gearbox leakage & Troubleshooting Gearbox OIL LeakageWheel Spacing Acceptable Oil LeakageReplacing Flail Knives Replacing Rubber Shield FlapsServicing Rotors Flail Tubes Removing ComponentsReplacing Components Replacing Stub ShaftIf removing rotor drive coupling, use Loctite No Or equivalent and special high collar lockRemoving the Driveline Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Troubleshooting TroubleshootingContour Flail Patterns Worksheet for Contour Flail Patterns24’ Assembly AssemblyWheel Assembly Dealer SET-UP InstructionsFloating Upper Mast Installed Point UnitsManual Storage Tube Installation Rubber Belting InstallationRubber Flap Installation ALL UnitsSafety Light Installation Safety Light Installed Wiring HarnessEND TOW Hitch Installation Optional Equipment Install Center DeflectorCenter CUT KIT Installation Block ShreddedInstall Motor Housing Figure Assemble Motor and Blade FigureAssembly Hoses Motor Assembly InstalledInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index Flail Shredder PartsCenter Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightStrut and Caster Assembly END TOW and Safety Light Assembly END TOW Assembly and Safety Light Part List Weasler Automatic ClutchWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Center Drive Gearbox Rubber Belting Hydraulic Hose Assembly Rubber FlapAdvertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalBolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexWarranty Rev /3/2011 MAN0943 Woods Equipment Company

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents