Woods Equipment S30CD manual Install Hose Clamps, Connect Hoses to Tractor, Install Decals

Page 45

Install Hose Clamps

1.Place hose clamps (36) around hoses (11) and center hoses between center plate.

2.Mark clamp holes in desired location on shedder body and drill two 11/32" holes.

3.Secure hose clamps to shredder using 5/16 NF x 1-1/4 cap screws (20), flat washers (33), lock washers (34) and hex nuts (35). See Figure 56.

Figure 56. Hose Clamp Installation

Connect Hoses to Tractor

NOTICE

■Oil flow to hydraulic motor must not exceed 28 gpm.

1.Connect PRESSURE hose to a tractor rear remote quick coupler that has a lever (handle) that can be placed in the detent or locked position.

2.RETURN hose must be connected directly to the tractor reservoir or to a specifically designated motor return or ‘zero’ back pressure port.

Install Decals

Apply safety decals (24 & 25) to a clean surface on the back of the shredder where they can be seen without obstructions. Install decals (25) on either side of the hose assembly. See Figure 56.

Remove Deflector Kit

1022652 deflector kit must be removed from the shred- der before using cutter kit. Deflector kit pushes material away from the cutter kit and preventing material from being cut.

™

MAN0943 (07/12/2011)

Assembly 45

 

 

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Flail Shredder To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementSafety Rules SafetyPreparation TrainingOperation TransportationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordOperation OperationPrincipal Components BREAK-IN of the Flail ShredderTractor Weight HorsepowerPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Point HitchLoad Sensing Hydraulics 3-Point Models Only Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Removing Shredder from Tractor Without Quick Hitch AttachmentPreparing for Operation Rubber Flaps or BeltingFlail Knives Flail HeightSetting Flail Height Setting Caster WheelsStarting the Shredder Stopping the Shredder CleaningHazard Area Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Service & Maintenance Service & MaintenanceLubricants GreasingEvery 25 hours of operation Daily or every 8 hours of operationAnnually Every 40 hours of operation FigureLubrication Service Record Hours Serviced by Hours or dailyHours Gearbox OIL Leakage Gearbox leakage & TroubleshootingAcceptable Oil Leakage Wheel SpacingReplacing Rubber Shield Flaps Replacing Flail KnivesRemoving Components Servicing Rotors Flail TubesReplacing Stub Shaft Replacing ComponentsIf removing rotor drive coupling, use Loctite No Or equivalent and special high collar lockRemoving the Driveline Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Troubleshooting TroubleshootingWorksheet for Contour Flail Patterns Contour Flail Patterns24’ Assembly AssemblyWheel Assembly Dealer SET-UP InstructionsPoint Units Floating Upper Mast InstalledRubber Belting Installation Manual Storage Tube InstallationRubber Flap Installation ALL UnitsSafety Light Installed Wiring Harness Safety Light InstallationOptional Equipment Install Center Deflector END TOW Hitch InstallationCenter CUT KIT Installation Block ShreddedAssemble Motor and Blade Figure Install Motor Housing FigureMotor Assembly Installed Assembly HosesInstall Decals Install Hose ClampsConnect Hoses to Tractor Remove Deflector KitDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Parts Index Flail ShredderCenter Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyStrut and Caster Assembly END TOW and Safety Light Assembly END TOW Assembly and Safety Light Part List Weasler Automatic ClutchWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Center Drive Gearbox Rubber Belting Rubber Flap Hydraulic Hose AssemblyCenter Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListSAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Rev /3/2011 Woods Equipment Company MAN0943

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents