Woods Equipment S30CD manual Assembly, Dealer SET-UP Instructions, For Some Models Shipped on End

Page 38

ASSEMBLY

DEALER SET-UP INSTRUCTIONS

„Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

„Do not handle knives with bare hands. Careless or improper handling may result in serious injury.

„Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death.

„Make sure that all operating and service person- nel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gan- grene, serious injury, or death will result. CON-

TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. DO NOT DELAY.

„Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

CAUTION

„Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

„Use a suitable lifting device of sufficient capac- ity. Use adequate personnel to handle heavy com- ponents.

1.Open the crate and cartons containing the attaching components and mounting hardware.

2.Use the packing list to check that all parts have been shipped.

For Some Models Shipped on End

Units that stand on their aft ends during shipping have a dipstick shipping plug installed in the gearbox dipstick tube to prevent leakage during shipping.

NOTICE

■For units shipped on aft end, the dipstick ship- ping plug must be removed before shredder opera- tion. Replace plug with dipstick in filler tube after shredder has been removed from truck and leveled.

After the unit has been leveled for a couple of hours, check oil level and service through the dipstick/filler tube as required.

Figure 39. Dipstick Shipping Plug Removal

WHEEL ASSEMBLY

1.To get desired row spacing, measure from center of frame and mark suspension mounting tubes.

2.Bolt strut uprights to shredder frame but do not tighten at this time, Figure 40. See parts list pages 48 and 49 for hardware sizes.

Figure 40. Strut Uprights Installed

38 Assembly

MAN0943 (07/12/2011)

 

 

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Flail Shredder Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications Balance Statement General InformationPreparation SafetySafety Rules TrainingTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordPrincipal Components OperationOperation BREAK-IN of the Flail ShredderPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorLoad Sensing Hydraulics 3-Point Models Only PTO Driveline LengthPoint Hitch Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Without Quick Hitch Attachment Removing Shredder from TractorFlail Knives Rubber Flaps or BeltingPreparing for Operation Flail HeightStarting the Shredder Setting Flail HeightSetting Caster Wheels Hazard Area CleaningStopping the Shredder Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Lubricants Service & MaintenanceService & Maintenance GreasingDaily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation Figure AnnuallyHours Lubrication Service Record Hours Serviced byHours or daily Gearbox leakage & Troubleshooting Gearbox OIL LeakageWheel Spacing Acceptable Oil LeakageReplacing Flail Knives Replacing Rubber Shield FlapsServicing Rotors Flail Tubes Removing ComponentsIf removing rotor drive coupling, use Loctite No Replacing ComponentsReplacing Stub Shaft Or equivalent and special high collar lockMounting Clutch to Shredder Removing the DrivelineRebuilding Overrunning Clutch Service & Maintenance Troubleshooting TroubleshootingContour Flail Patterns Worksheet for Contour Flail Patterns24’ Wheel Assembly AssemblyAssembly Dealer SET-UP InstructionsFloating Upper Mast Installed Point UnitsRubber Flap Installation Manual Storage Tube InstallationRubber Belting Installation ALL UnitsSafety Light Installation Safety Light Installed Wiring HarnessCenter CUT KIT Installation END TOW Hitch InstallationOptional Equipment Install Center Deflector Block ShreddedInstall Motor Housing Figure Assemble Motor and Blade FigureAssembly Hoses Motor Assembly InstalledConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListParts Index Flail Shredder PartsCenter Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightStrut and Caster Assembly END TOW and Safety Light Assembly Weasler 30K 3-POINT PTO Shaft with Automatic Clutch END TOW Assembly and Safety Light Part ListWeasler Automatic Clutch Center Drive Gearbox Rubber Belting Hydraulic Hose Assembly Rubber FlapAdvertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalMetric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexWarranty Rev /3/2011 MAN0943 Woods Equipment Company

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents