Woods Equipment S30CD manual Assemble Motor and Blade Figure, Install Motor Housing Figure

Page 43

Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause shredder to fall.

2.Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety.

The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure shredder is approximately level.

3.With full shredder weight lowered onto jackstands, test blocking stability before working underneath.

4.If shredder is attached to tractor when blocking, set the brakes, remove key, and block shredder before working underneath.

5.Securely block rear tractor wheels, in front and behind. Tighten tractor lower 3-point arm anti-sway mechanism to prevent side-to-side movement.

Assemble Motor and Blade - Figure 52

1.Install elbow (8), adapter (9), elbow (10) and hose

(11)to the IN or PRESSURE side of the hydraulic motor.

2.Install adapter (23) and hose (11) to the OUT or RETURN side of the motor.

3.Place motor (4) inside motor housing (2) and secure using six 9/16 NC x 1-1/2 cap screws (7) lock nuts (6).

Make sure OUT or RETRUN side of motor is on the open side of the motor housing. Torque hardware to 171 lbs-ft.

4.Slide blade hub (1) over motor shaft, install 1/4" key and secure using one 5/16 NF x 1-1/2 cap screw (20), flat washers (33) and lock washer (34) in the bottom of the shaft. Torque to 19 lbs-ft.

5.Clamp hub to shaft using two 3/8 NC x 1-3/4 cap screws (18) and lock nuts (22). Torque to 35 lbs-ft.

6.Secure blade (3) to blade hub using two 3/8 NC x 1-1/4 cap screws (19) and flange lock nuts (22). Torque to 35 lbs-ft.

Figure 52. Motor Assembly

Install Motor Housing - Figure 53

1.Slide motor assembly between shredder center channel and secure to the left side using two 1/2 NC x 1-1/4 carriage bolts (29) and flange lock nuts

(30).

2.Install 1/2 NC x 1 cap screw (31) and flat washer

(32)to the right rear hole of the motor housing and secure with flange lock nuts (30).

3.Install 1/2 NC x 1-1/4 carriage bolt (29) and flange lock nut (30) into the right front hole.

4.Raise motor housing to the bottom of the mounting slots and torque hardware to 85 lbs-ft.

MAN0943 (07/12/2011)

Assembly 43

 

 

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Flail Shredder To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementTraining SafetySafety Rules PreparationOperation TransportationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordBREAK-IN of the Flail Shredder OperationOperation Principal ComponentsChoosing the Correct Tractor HorsepowerTractor Weight PRE-OPERATION Check ListPoint Hitch PTO Driveline LengthLoad Sensing Hydraulics 3-Point Models Only With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Removing Shredder from Tractor Without Quick Hitch AttachmentFlail Height Rubber Flaps or BeltingPreparing for Operation Flail KnivesSetting Caster Wheels Setting Flail HeightStarting the Shredder Ground Speed CleaningStopping the Shredder Hazard AreaDo not exceed 20 MPH while transporting shredder Operation Greasing Service & MaintenanceService & Maintenance LubricantsEvery 25 hours of operation Daily or every 8 hours of operationAnnually Every 40 hours of operation FigureHours or daily Lubrication Service Record Hours Serviced byHours Gearbox OIL Leakage Gearbox leakage & TroubleshootingAcceptable Oil Leakage Wheel SpacingReplacing Rubber Shield Flaps Replacing Flail KnivesRemoving Components Servicing Rotors Flail TubesOr equivalent and special high collar lock Replacing ComponentsReplacing Stub Shaft If removing rotor drive coupling, use Loctite NoRebuilding Overrunning Clutch Removing the DrivelineMounting Clutch to Shredder Service & Maintenance Troubleshooting TroubleshootingWorksheet for Contour Flail Patterns Contour Flail Patterns24’ Dealer SET-UP Instructions AssemblyAssembly Wheel AssemblyPoint Units Floating Upper Mast InstalledALL Units Manual Storage Tube InstallationRubber Belting Installation Rubber Flap InstallationSafety Light Installed Wiring Harness Safety Light InstallationBlock Shredded END TOW Hitch InstallationOptional Equipment Install Center Deflector Center CUT KIT InstallationAssemble Motor and Blade Figure Install Motor Housing FigureMotor Assembly Installed Assembly HosesRemove Deflector Kit Install Hose ClampsInstall Decals Connect Hoses to TractorDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListParts Parts Index Flail ShredderCenter Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyStrut and Caster Assembly END TOW and Safety Light Assembly Weasler Automatic Clutch END TOW Assembly and Safety Light Part ListWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Center Drive Gearbox Rubber Belting Rubber Flap Hydraulic Hose AssemblyCenter Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListAppendix Bolt Torque ChartSAE Series Torque Chart Metric Series Torque ChartAbbreviations Bolt Size ChartIndex IndexWarranty Rev /3/2011 Woods Equipment Company MAN0943

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents