Woods Equipment S30CD manual Troubleshooting

Page 35

TROUBLESHOOTING

The Woods Flail Shredder uses swinging flails to pick up and shred crop residue left in the field. It is a simple and reli- able system that requires minimal maintenance.

The following table lists problems, causes, and solutions that you may encounter. If you encounter a problem that is dif- ficult to solve even after reading through this table, please call your local Woods dealer. When calling, please have this manual and your unit’s serial number ready.

PROBLEM

CAUSE

SOLUTION

 

 

 

Shredder doesn’t track

Poor wheel spacing

Set wheels in center of crop rows.

 

3-Point not set

Set 3-point hitch in non-sway

 

 

position.

 

Shredder not level

Level shredder (see Set Operating

 

 

Height, page 19).

 

Irrigation furrows not even

Set wheels against seed bed

 

 

 

Shredder doesn’t follow

3-Point not set

Set 3 point in float position.

ground contour

 

 

 

 

See tractor manual to set Load

 

 

Sensing hydraulic system.

 

Shredder too high

Set shredder closer to ground.

 

Irrigation furrows not even

Set wheels against seed bed.

 

 

 

Shredder vibrates

Driveline doesn’t telescope.

Remove, disassemble, and clean

 

 

telescoping joint.

 

Rotor out of balance

Replace damaged or broken flails

 

 

and flails 180 degrees opposite.

 

 

Check for missing balance weights or

 

 

rebalance.

 

 

 

Debris is being thrown out

Shredder set too low

Raise shredder.

from under shredder

 

 

 

Knives excessively worn

Replace knives.

 

Rubber shields missing

Replace flaps immediately.

 

 

 

Crop residue is being left

Traveling too fast

Slow travel speed.

 

Shredder too high

Lower shredder.

 

Improper Knives

Change Knives.

 

Crop residue strip left in shredder

Add center cutter or divider.

 

center

 

 

 

 

MAN0943 (07/12/2011)

Troubleshooting 35

 

 

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Flail Shredder To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementTraining SafetySafety Rules PreparationOperation TransportationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordBREAK-IN of the Flail Shredder OperationOperation Principal ComponentsChoosing the Correct Tractor HorsepowerTractor Weight PRE-OPERATION Check ListLoad Sensing Hydraulics 3-Point Models Only PTO Driveline LengthPoint Hitch Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Removing Shredder from Tractor Without Quick Hitch AttachmentFlail Height Rubber Flaps or BeltingPreparing for Operation Flail KnivesStarting the Shredder Setting Flail HeightSetting Caster Wheels Ground Speed CleaningStopping the Shredder Hazard AreaDo not exceed 20 MPH while transporting shredder Operation Greasing Service & MaintenanceService & Maintenance LubricantsEvery 25 hours of operation Daily or every 8 hours of operationAnnually Every 40 hours of operation FigureHours Lubrication Service Record Hours Serviced byHours or daily Gearbox OIL Leakage Gearbox leakage & TroubleshootingAcceptable Oil Leakage Wheel SpacingReplacing Rubber Shield Flaps Replacing Flail KnivesRemoving Components Servicing Rotors Flail TubesOr equivalent and special high collar lock Replacing ComponentsReplacing Stub Shaft If removing rotor drive coupling, use Loctite NoMounting Clutch to Shredder Removing the DrivelineRebuilding Overrunning Clutch Service & Maintenance Troubleshooting TroubleshootingWorksheet for Contour Flail Patterns Contour Flail Patterns24’ Dealer SET-UP Instructions AssemblyAssembly Wheel AssemblyPoint Units Floating Upper Mast InstalledALL Units Manual Storage Tube InstallationRubber Belting Installation Rubber Flap InstallationSafety Light Installed Wiring Harness Safety Light InstallationBlock Shredded END TOW Hitch InstallationOptional Equipment Install Center Deflector Center CUT KIT InstallationAssemble Motor and Blade Figure Install Motor Housing FigureMotor Assembly Installed Assembly HosesRemove Deflector Kit Install Hose ClampsInstall Decals Connect Hoses to TractorDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListParts Parts Index Flail ShredderCenter Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyStrut and Caster Assembly END TOW and Safety Light Assembly Weasler 30K 3-POINT PTO Shaft with Automatic Clutch END TOW Assembly and Safety Light Part ListWeasler Automatic Clutch Center Drive Gearbox Rubber Belting Rubber Flap Hydraulic Hose AssemblyCenter Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListAppendix Bolt Torque ChartSAE Series Torque Chart Metric Series Torque ChartAbbreviations Bolt Size ChartIndex IndexWarranty Rev /3/2011 Woods Equipment Company MAN0943

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents