Woods Equipment S30CD manual Every 40 hours of operation Figure, Annually

Page 26

Every 40 hours of operation - Figure 24

1.Lubricate rotor drive couplers next to the couplers on underside of unit and inside of flail tube (access through windows on back panel of shredder).

2.Grease the drive hubs with 10 to 20 pumps. You may use extra grease only on drive hubs.

DP109

Figure 24. Drive Couplers and Hubs

Annually

1.Change gearbox oil. Refill with SAE 85W90 gear oil. Capacity: 2-1/2 U.S. quarts (110 oz.). See Figure 25.

GEARBOX

OIL DRAIN

DP15

Figure 25. Gearbox Oil Drain Location

2.Repack wheel bearings. See Figure 26.

DP110

Figure 26. Wheel Bearings

3.Lubricate pivot tube (2 locations each pivot tube). See Figure 27.

DP113

Figure 27. Pivot Tube Lubrication Points

4.Lubricate caster pivot bearings as shown in Figure 28.

DP108

Figure 28. Wheel Caster Bearing

Lubrication Points

26 Service & Maintenance	MAN0943 (07/12/2011)

Image 26

Contents Flail Shredder Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications Balance Statement General InformationPreparation SafetySafety Rules TrainingTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordPrincipal Components OperationOperation BREAK-IN of the Flail ShredderPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorLoad Sensing Hydraulics 3-Point Models Only PTO Driveline LengthPoint Hitch Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Without Quick Hitch Attachment Removing Shredder from TractorFlail Knives Rubber Flaps or BeltingPreparing for Operation Flail HeightStarting the Shredder Setting Flail HeightSetting Caster Wheels Hazard Area CleaningStopping the Shredder Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Lubricants Service & MaintenanceService & Maintenance GreasingDaily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation Figure AnnuallyHours Lubrication Service Record Hours Serviced byHours or daily Gearbox leakage & Troubleshooting Gearbox OIL LeakageWheel Spacing Acceptable Oil LeakageReplacing Flail Knives Replacing Rubber Shield FlapsServicing Rotors Flail Tubes Removing ComponentsIf removing rotor drive coupling, use Loctite No Replacing ComponentsReplacing Stub Shaft Or equivalent and special high collar lockMounting Clutch to Shredder Removing the DrivelineRebuilding Overrunning Clutch Service & Maintenance Troubleshooting TroubleshootingContour Flail Patterns Worksheet for Contour Flail Patterns24’ Wheel Assembly AssemblyAssembly Dealer SET-UP InstructionsFloating Upper Mast Installed Point UnitsRubber Flap Installation Manual Storage Tube InstallationRubber Belting Installation ALL UnitsSafety Light Installation Safety Light Installed Wiring HarnessCenter CUT KIT Installation END TOW Hitch InstallationOptional Equipment Install Center Deflector Block ShreddedInstall Motor Housing Figure Assemble Motor and Blade FigureAssembly Hoses Motor Assembly InstalledConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListParts Index Flail Shredder PartsCenter Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightStrut and Caster Assembly END TOW and Safety Light Assembly Weasler 30K 3-POINT PTO Shaft with Automatic Clutch END TOW Assembly and Safety Light Part ListWeasler Automatic Clutch Center Drive Gearbox Rubber Belting Hydraulic Hose Assembly Rubber FlapAdvertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalMetric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexWarranty Rev /3/2011 MAN0943 Woods Equipment Company