Woods Equipment S30CD END TOW Hitch Installation, Optional Equipment Install Center Deflector

Page 42

END TOW HITCH INSTALLATION

1.Attach lower end tow hitch mount (4) using carriage bolts (26), and lock nuts (25).

2.Attach tongue lockup bracket (3) using carriage bolts (26), and locknuts (25).

3.Bolt hitch (1) to tow hitch mount brackets (33) using cap screws (27) and locknuts (28).

4.Attach hose bracket (13) to shredder using carriage bolts (26), flat washer (14) and locknuts (25).

5.Secure tongue (1) to tow hitch mount (4) using cap screws (27) and locknuts (28).

6.Install safety chain.

7.Store tongue (1) and wire harness as shown, Figure 49.

1. Tongue

3.Tongue Lock Up

13. Hose Bracket

14. 1/2 Flat Washer

15. 3/4 Hitch Pin

25. 1/2 NC Flanged Lock Nut

26. 1/2 NC x 1-1/2 Carriage Bolt

27. 5/8 NC x 9 HHCS

28. 5/8 NC Flanged Lock Nut

33. Lower End Transport Mount

35. Pin

Figure 50. End Tow Hitch Installation

OPTIONAL EQUIPMENT

INSTALL CENTER DEFLECTOR

Slide deflector (1) between shredder center channel with the point forward.

Secure into position using four 1/2 NC x 1-1/4 carriage bolts (2) and flange lock nuts (3).

3 2

DP3

1

1.Center deflector

2.1/2 NC x 1-1/4 carriage bolt

3.1/2 NC Flange lock nut

Figure 51. Center Deflector Installed

CENTER CUT KIT INSTALLATION

Block Shredded

„Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

To minimize the potential hazards of working under- neath the shredder, follow these procedures.

1.Jackstands with a load rating of 2000 lbs or more are the only approved blocking device for this shredder. Install a minimum of four jackstands under the shredder before working underneath unit.

42 Assembly

MAN0943 (07/12/2011)

 

 

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Flail Shredder Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications Balance Statement General InformationPreparation SafetySafety Rules TrainingTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordPrincipal Components OperationOperation BREAK-IN of the Flail ShredderPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorPTO Driveline Length Point HitchLoad Sensing Hydraulics 3-Point Models Only Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Without Quick Hitch Attachment Removing Shredder from TractorFlail Knives Rubber Flaps or BeltingPreparing for Operation Flail HeightSetting Flail Height Setting Caster WheelsStarting the Shredder Hazard Area CleaningStopping the Shredder Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Lubricants Service & MaintenanceService & Maintenance GreasingDaily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation Figure AnnuallyLubrication Service Record Hours Serviced by Hours or dailyHours Gearbox leakage & Troubleshooting Gearbox OIL LeakageWheel Spacing Acceptable Oil LeakageReplacing Flail Knives Replacing Rubber Shield FlapsServicing Rotors Flail Tubes Removing ComponentsIf removing rotor drive coupling, use Loctite No Replacing ComponentsReplacing Stub Shaft Or equivalent and special high collar lockRemoving the Driveline Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Troubleshooting TroubleshootingContour Flail Patterns Worksheet for Contour Flail Patterns24’ Wheel Assembly AssemblyAssembly Dealer SET-UP InstructionsFloating Upper Mast Installed Point UnitsRubber Flap Installation Manual Storage Tube InstallationRubber Belting Installation ALL UnitsSafety Light Installation Safety Light Installed Wiring HarnessCenter CUT KIT Installation END TOW Hitch InstallationOptional Equipment Install Center Deflector Block ShreddedInstall Motor Housing Figure Assemble Motor and Blade FigureAssembly Hoses Motor Assembly InstalledConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListParts Index Flail Shredder PartsCenter Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightStrut and Caster Assembly END TOW and Safety Light Assembly END TOW Assembly and Safety Light Part List Weasler Automatic ClutchWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Center Drive Gearbox Rubber Belting Hydraulic Hose Assembly Rubber FlapAdvertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalMetric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexWarranty Rev /3/2011 MAN0943 Woods Equipment Company

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents