Woods Equipment S30CD manual Dealer Check Lists, PRE-DELIVERY Check List, Delivery Check List

Page 46

DEALER CHECK LISTS

PRE-DELIVERY CHECK LIST

(DEALER’S RESPONSIBILITY)

Inspect the equipment thoroughly after assembly to make sure that it is set up properly before delivering it to the customer.

The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made.

___ Check that all safety decals are installed and in good condition. Replace if damaged.

___ Properly attach implement to tractor and make all necessary adjustments.

___ Check all bolts to be sure they are properly torqued.

___ Check wheel bolts for proper torque.

___ Check that all cotter pins and safety pins are properly installed. Replace if damaged.

___ Check and grease all lubrication points as identi- fied in . Lubrication Points, page 25.

DELIVERY CHECK LIST

(DEALER’S RESPONSIBILITY)

___ Show customer how to make adjustments.

___ Instruct customer how to lubricate and explain the importance of lubrication.

___ Point out the safety decals. Explain their meaning and the need to keep them in place and in good condition. Emphasize the increased safety haz- ards when instructions are not followed.

___ Present Operator's Manual and request that cus- tomer and all operators read it before operating equipment. Point out the manual safety rules, explain their meanings and emphasize the increased safety hazards that exist when safety rules are not followed.

___ Explain to customer the potential crushing haz- ards of going underneath raised equipment. Instruct customer that service work does not require going underneath unit and never to do so.

___ Show customer the safe, proper procedures to be used when mounting, dismounting, and storing equipment.

___ For mounted units, add wheel weights, ballast in front tires, and/or front tractor weight to enhance front end stability. A minimum 20% of tractor and equipment gross weight must be on front tractor wheels. When adding weight to attain 20% of tractor and equipment weight on front tractor wheels, you must not exceed the ROPS weight certification. Weigh the tractor and equipment. Do not estimate!

___ Make customer aware of optional equipment available so that customer can make proper choices as required.

™

46 Dealer Check Lists

MAN0943 (07/12/2011)

 

 

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Flail Shredder Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications Balance Statement General InformationPreparation SafetySafety Rules TrainingTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordPrincipal Components OperationOperation BREAK-IN of the Flail ShredderPRE-OPERATION Check List HorsepowerTractor Weight Choosing the Correct TractorPoint Hitch PTO Driveline LengthLoad Sensing Hydraulics 3-Point Models Only With Quick Hitch Attachment Attaching Shredder to TractorCut only the male end. Never cut the female end Without Quick Hitch Attachment Removing Shredder from TractorFlail Knives Rubber Flaps or BeltingPreparing for Operation Flail HeightSetting Caster Wheels Setting Flail HeightStarting the Shredder Hazard Area CleaningStopping the Shredder Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Lubricants Service & MaintenanceService & Maintenance GreasingDaily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation Figure AnnuallyHours or daily Lubrication Service Record Hours Serviced byHours Gearbox leakage & Troubleshooting Gearbox OIL LeakageWheel Spacing Acceptable Oil LeakageReplacing Flail Knives Replacing Rubber Shield FlapsServicing Rotors Flail Tubes Removing ComponentsIf removing rotor drive coupling, use Loctite No Replacing ComponentsReplacing Stub Shaft Or equivalent and special high collar lockRebuilding Overrunning Clutch Removing the DrivelineMounting Clutch to Shredder Service & Maintenance Troubleshooting TroubleshootingContour Flail Patterns Worksheet for Contour Flail Patterns24’ Wheel Assembly AssemblyAssembly Dealer SET-UP InstructionsFloating Upper Mast Installed Point UnitsRubber Flap Installation Manual Storage Tube InstallationRubber Belting Installation ALL UnitsSafety Light Installation Safety Light Installed Wiring HarnessCenter CUT KIT Installation END TOW Hitch InstallationOptional Equipment Install Center Deflector Block ShreddedInstall Motor Housing Figure Assemble Motor and Blade FigureAssembly Hoses Motor Assembly InstalledConnect Hoses to Tractor Install Hose ClampsInstall Decals Remove Deflector KitPRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListParts Index Flail Shredder PartsCenter Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightStrut and Caster Assembly END TOW and Safety Light Assembly Weasler Automatic Clutch END TOW Assembly and Safety Light Part ListWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Center Drive Gearbox Rubber Belting Hydraulic Hose Assembly Rubber FlapAdvertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalMetric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexWarranty Rev /3/2011 MAN0943 Woods Equipment Company

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents