Woods Equipment S30CD manual Service & Maintenance, Lubricants, Greasing, Lubrication Schedule

Page 24

SERVICE & MAINTENANCE

„Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pres- sure, set parking brake, stop engine, remove key, and unfasten seat belt.

„Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

„Do not handle knives with bare hands. Careless or improper handling may result in serious injury.

„Make sure shields and guards are properly installed and in good condition. Replace if damaged.

CAUTION

„Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

„Make certain all movement of equipment com- ponents has stopped before approaching for ser- vice.

LUBRICANTS

1.Grease

Use an SAE multi-purpose high temperature

grease with extreme pressure (EP) performance. An SAE multi-purpose lithium-based grease is also acceptable.

2.Gearbox Oil

Use an SAE 85W90 gear oil for all operating conditions. Capacity: 2-1/2 U.S. quarts (110 oz.).

Storing Lubricants

Your unit can operate at top efficiency only if clean lubricants are used. Use clean containers to handle all lubricants. Store them in an area protected from dust, moisture, and other contaminants.

GREASING

NOTE: Use the Lubrication Service Record, page 27 to keep a record of all scheduled maintenance.

1.Use a hand-held grease gun for all greasing.

2.Wipe grease fitting with a clean cloth before greasing to avoid injecting dirt and grit.

3.Replace and repair broken fittings immediately.

4.If fittings will not take grease, remove and clean thoroughly. Also clean lubricant passageway. Replace fitting if necessary.

LUBRICATION SCHEDULE

NOTE: Recommendations are based on normal oper- ating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes. Refer to Figure 21.

Daily or every 8 hours of operation

PTO Driveline Lubricate daily or every 8 hours of oper- ation. See Figure 20 for lubrication points.

24 Service & Maintenance

MAN0943 (07/12/2011)

 

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Flail Shredder Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications Balance Statement General InformationSafety Safety RulesPreparation TrainingTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation OperationPrincipal Components BREAK-IN of the Flail ShredderHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorPTO Driveline Length Point HitchLoad Sensing Hydraulics 3-Point Models Only Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Without Quick Hitch Attachment Removing Shredder from TractorRubber Flaps or Belting Preparing for OperationFlail Knives Flail HeightSetting Flail Height Setting Caster WheelsStarting the Shredder Cleaning Stopping the ShredderHazard Area Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Service & Maintenance Service & MaintenanceLubricants GreasingDaily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation Figure AnnuallyLubrication Service Record Hours Serviced by Hours or dailyHours Gearbox leakage & Troubleshooting Gearbox OIL LeakageWheel Spacing Acceptable Oil LeakageReplacing Flail Knives Replacing Rubber Shield FlapsServicing Rotors Flail Tubes Removing ComponentsReplacing Components Replacing Stub ShaftIf removing rotor drive coupling, use Loctite No Or equivalent and special high collar lockRemoving the Driveline Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Troubleshooting TroubleshootingContour Flail Patterns Worksheet for Contour Flail Patterns24’ Assembly AssemblyWheel Assembly Dealer SET-UP InstructionsFloating Upper Mast Installed Point UnitsManual Storage Tube Installation Rubber Belting InstallationRubber Flap Installation ALL UnitsSafety Light Installation Safety Light Installed Wiring HarnessEND TOW Hitch Installation Optional Equipment Install Center DeflectorCenter CUT KIT Installation Block ShreddedInstall Motor Housing Figure Assemble Motor and Blade FigureAssembly Hoses Motor Assembly InstalledInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index Flail Shredder PartsCenter Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightStrut and Caster Assembly END TOW and Safety Light Assembly END TOW Assembly and Safety Light Part List Weasler Automatic ClutchWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Center Drive Gearbox Rubber Belting Hydraulic Hose Assembly Rubber FlapAdvertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalBolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexWarranty Rev /3/2011 MAN0943 Woods Equipment Company

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents