Woods Equipment S30CD manual Attaching Shredder to Tractor, With Quick Hitch Attachment

Page 17

7.Use an abrasive wheel power saw to cut the male end of the shaft. Cut the same amount from both the splined shaft and the safety shield. See Figure 4. Use a file to remove any burrs from the cut end.

NOTICE

■Cut only the male end. Never cut the female end.

8.Never cut more than 9 inches from the male end. Cutting 1 inch from the male end shortens both the minimum and maximum lengths by 1 inch.

Figure 4. Cutting the Driveline Shaft

ATTACHING SHREDDER TO TRACTOR

1.Place unit on a level, dry area free of debris and other foreign object.

„Keep bystanders away from equipment.

„Connect PTO driveline directly to power unit PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

2.Clear the area of bystanders, especially children.

3.Provide enough clearance to back the tractor safely into the unit.

CAUTION

■Do not allow anyone to stand between tractor and unit when backing up to the unit.

With Quick Hitch Attachment:

4.Set the height of the 3-point hitch so that quick hitch claws are lower than the mounting pins.

5.Make sure 3-point hitch is set in the non-sway position. See tractor manual for details.

6.Align the claws under the lower and upper mast mounting pins while backing up.

NOTE: For a Category II hitch, use the bottom upper mast hole. For a Category III hitch, use the top upper mast hole.

7.When the claws are under the pins, slowly raise the 3-point hitch. Make sure each mounting pin seats in its respective claw.

8.Release the claw retainer locks to secure the mounting pins in the claws.

9.Check the top link frame. It should be free to slide in its mounting slots. This movement allows the unit to follow the ground contour when cresting a hill or going through a depression.

Figure 5. Driveline Dimension

MAN0943 (07/12/2011)

Operation 17

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Flail Shredder To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementSafety Rules SafetyPreparation TrainingOperation TransportationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordOperation OperationPrincipal Components BREAK-IN of the Flail ShredderTractor Weight HorsepowerPRE-OPERATION Check List Choosing the Correct TractorLoad Sensing Hydraulics 3-Point Models Only PTO Driveline LengthPoint Hitch Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Removing Shredder from Tractor Without Quick Hitch AttachmentPreparing for Operation Rubber Flaps or BeltingFlail Knives Flail HeightStarting the Shredder Setting Flail HeightSetting Caster Wheels Stopping the Shredder CleaningHazard Area Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Service & Maintenance Service & MaintenanceLubricants GreasingEvery 25 hours of operation Daily or every 8 hours of operationAnnually Every 40 hours of operation FigureHours Lubrication Service Record Hours Serviced byHours or daily Gearbox OIL Leakage Gearbox leakage & TroubleshootingAcceptable Oil Leakage Wheel SpacingReplacing Rubber Shield Flaps Replacing Flail KnivesRemoving Components Servicing Rotors Flail TubesReplacing Stub Shaft Replacing ComponentsIf removing rotor drive coupling, use Loctite No Or equivalent and special high collar lockMounting Clutch to Shredder Removing the DrivelineRebuilding Overrunning Clutch Service & Maintenance Troubleshooting TroubleshootingWorksheet for Contour Flail Patterns Contour Flail Patterns24’ Assembly AssemblyWheel Assembly Dealer SET-UP InstructionsPoint Units Floating Upper Mast InstalledRubber Belting Installation Manual Storage Tube InstallationRubber Flap Installation ALL UnitsSafety Light Installed Wiring Harness Safety Light InstallationOptional Equipment Install Center Deflector END TOW Hitch InstallationCenter CUT KIT Installation Block ShreddedAssemble Motor and Blade Figure Install Motor Housing FigureMotor Assembly Installed Assembly HosesInstall Decals Install Hose ClampsConnect Hoses to Tractor Remove Deflector KitDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Parts Index Flail ShredderCenter Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyStrut and Caster Assembly END TOW and Safety Light Assembly Weasler 30K 3-POINT PTO Shaft with Automatic Clutch END TOW Assembly and Safety Light Part ListWeasler Automatic Clutch Center Drive Gearbox Rubber Belting Rubber Flap Hydraulic Hose AssemblyCenter Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListSAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Rev /3/2011 Woods Equipment Company MAN0943

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents