Woods Equipment S30CD manual Point Units, Floating Upper Mast Installed

Page 39

3.Attach crossmember to strut uprights. Tighten all mounting hardware at this time per torque chart, Figure 41.

DP121

Figure 41. Crossmember Installed

4.Pin pivot tubes and caster pivots to strut uprights as shown, Figure 42.

5.Attach cylinders, Figure 42.

DP122

Figure 42. Pivot Tubes, Caster Pivots & Cylinders

Installed

6.Attach caster yoke assembly to pivot assembly, Figure 43. Use Loctite on hex bolt.

1

Use Loctite

DP123

Figure 43. Caster Yoke Installed

7.Attach cylinders, fittings, and hoses. See parts section.

8.Connect hoses to tractor and cycle cylinder in and out to remove air from system. Check for leaks at this time.

9.While shredder is setting on skids, retract cylinders fully until cast yokes are high enough to mount wheels. Torque wheel nuts per torque chart.

10.Check tire pressure. Recommended tire pressure is 30 PSI.

11.Tighten mounting bolts to their specified torque.

3-POINT UNITS

12.Attach floating upper mast (1) to shredder using two hardened bushings, 1 x 5" hex bolts, lock nuts, and four 3/4 x 3" spacers. (Keep hardware loose.)

13.Attach front top link spacer, bolts, and lock nuts to front of upper mast assembly.

NOTE:

For Quick Hitch Cat II, use spacer in front lower hole of upper mast assembly.

For Quick Hitch Cat III, use spacer in front upper hole of upper mast assembly.

Without Quick Hitch, use spacer through top link pivot in front upper hole of upper mast assembly.

14.Assemble lower 3-point hitch pin assembly, spacers, and klik pin to lower mast (both sides).

NOTE: For Quick Hitch Cat II & III, place 1-3/4 OD spacer on the inside and 1-7/16 OD spacer on the outside.

1

DP11

Figure 44. Floating Upper Mast Installed

MAN0943 (07/12/2011)

Assembly 39

 

 

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Flail Shredder To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications General Information Balance StatementTraining SafetySafety Rules PreparationOperation TransportationMaintenance Storage Replace Immediately If Damaged Safety & Instructional DecalsPeligro Be Careful AdvertenciaOperator SIGN-OFF Record Operator RecordBREAK-IN of the Flail Shredder OperationOperation Principal ComponentsChoosing the Correct Tractor HorsepowerTractor Weight PRE-OPERATION Check ListPTO Driveline Length Point HitchLoad Sensing Hydraulics 3-Point Models Only Attaching Shredder to Tractor With Quick Hitch AttachmentCut only the male end. Never cut the female end Removing Shredder from Tractor Without Quick Hitch AttachmentFlail Height Rubber Flaps or BeltingPreparing for Operation Flail KnivesSetting Flail Height Setting Caster WheelsStarting the Shredder Ground Speed CleaningStopping the Shredder Hazard AreaDo not exceed 20 MPH while transporting shredder Operation Greasing Service & MaintenanceService & Maintenance LubricantsEvery 25 hours of operation Daily or every 8 hours of operationAnnually Every 40 hours of operation FigureLubrication Service Record Hours Serviced by Hours or dailyHours Gearbox OIL Leakage Gearbox leakage & TroubleshootingAcceptable Oil Leakage Wheel SpacingReplacing Rubber Shield Flaps Replacing Flail KnivesRemoving Components Servicing Rotors Flail TubesOr equivalent and special high collar lock Replacing ComponentsReplacing Stub Shaft If removing rotor drive coupling, use Loctite NoRemoving the Driveline Rebuilding Overrunning ClutchMounting Clutch to Shredder Service & Maintenance Troubleshooting TroubleshootingWorksheet for Contour Flail Patterns Contour Flail Patterns24’ Dealer SET-UP Instructions AssemblyAssembly Wheel AssemblyPoint Units Floating Upper Mast InstalledALL Units Manual Storage Tube InstallationRubber Belting Installation Rubber Flap InstallationSafety Light Installed Wiring Harness Safety Light InstallationBlock Shredded END TOW Hitch InstallationOptional Equipment Install Center Deflector Center CUT KIT InstallationAssemble Motor and Blade Figure Install Motor Housing FigureMotor Assembly Installed Assembly HosesRemove Deflector Kit Install Hose ClampsInstall Decals Connect Hoses to TractorDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListParts Parts Index Flail ShredderCenter Drive Flail Shredder Frame Assembly Part QTY Description Center Drive Flail Shredder Frame Assembly Parts ListLeft Right Flail Tube AssemblyStrut and Caster Assembly END TOW and Safety Light Assembly END TOW Assembly and Safety Light Part List Weasler Automatic ClutchWeasler 30K 3-POINT PTO Shaft with Automatic Clutch Center Drive Gearbox Rubber Belting Rubber Flap Hydraulic Hose AssemblyCenter Cutter KIT Optional AdvertenciaCenter Deflector Optional Center Cutter KIT Parts ListAppendix Bolt Torque ChartSAE Series Torque Chart Metric Series Torque ChartAbbreviations Bolt Size ChartIndex IndexWarranty Rev /3/2011 Woods Equipment Company MAN0943

S30CD specifications

The Woods Equipment S30CD is a highly regarded cutter designed for efficiency and performance in various landscaping and agricultural tasks. This model is particularly popular among professionals and homeowners who require robust machinery that can tackle tough terrain and heavy brush. As a part of the Woods Equipment family, the S30CD embodies a blend of innovative engineering and user-friendly design, making it a reliable choice for a wide range of applications.

One of the standout features of the S30CD is its powerful cutting capacity, thanks to its efficient design and robust construction. The cutter is equipped with a durable cutting deck that allows for effective brush and grass management, ensuring that it can handle dense vegetation without compromising performance. The S30CD’s cutting height is adjustable, providing versatility for different landscaping needs, whether it involves maintaining fields, pastures, or overgrown properties.

The S30CD is built with advanced technologies that enhance its operational capabilities. It features a unique blade design that not only provides superior cutting ability but also improves discharge performance, allowing clippings to be scattered evenly across the working area. This reduces the need for additional cleanup and helps in promoting healthy grass growth.

Another significant characteristic of the Woods Equipment S30CD is its ease of use. It is designed to be compatible with various tractors and implements, making it a versatile addition to any equipment lineup. The quick-attach system allows for easy mounting and dismounting, saving valuable time during transitions between tasks. Moreover, the ergonomic controls ensure that operators can manage the cutter comfortably and with precision.

Durability is a hallmark of the Woods Equipment S30CD, constructed with high-quality materials that stand up to wear and tear over time. This resilience not only extends the lifespan of the equipment but also makes it a cost-effective choice for regular use in demanding environments.

In summary, the Woods Equipment S30CD is a powerful, efficient, and user-friendly cutter designed for those who require high performance in brush management and landscaping. With its advanced cutting technologies, adjustable features, and robust construction, the S30CD stands out as an excellent investment for both professionals and homeowners looking to maintain their outdoor spaces effectively.
Top Page Image Contents