Woods Equipment S30CD manual Rubber Flap, Hydraulic Hose Assembly

Page 56

RUBBER FLAP

REF	PART	QTY	DESCRIPTION
1	50531089	30	Rubber flap (12")
2	1022659	7	Flap bracket, right
3	1022660	7	Flap bracket, left
5	1022655	2	Flap rod (20 ft)

REF	PART		QTY	DESCRIPTION
5	1029562		2	Flap rod (30’)
6	1026528		2	Swing flap bar, mast plate (32" all)
7	1026529		2	Swing flap bar (32", 20 ft, 25 ft, 27 ft)
8	6697	*	70	3/8 NC x 1 Carriage bolt
9	14350	*	70	3/8 NC Flange lock nut
10	90023043	*	4	3/16 x 1-1/2 cotter pin

* Standard hardware, obtain locally

				HYDRAULIC HOSE ASSEMBLY
REF	PART		QTY	DESCRIPTION
4	12422		2	Hose, .25 x .25NPT x 90L
20	66511		2	1/2 NPT Male Coupler
21	8572		8	3/8 x 1/4 x 90° Swivel
22	28522		8	Hose, .25 x .25 NPT x 54L
23	11893		10	1/4 NPTF Adapter
24	31208		4	Hose, .25 x .25 NPT x 124L
31	258	N/S	2	1/2 Feedline Clamp
32	24098	N/S	4	1-1/4 Cylinder Control Set
		N/S		Not Shown

56 Parts	MAN0943 (07/12/2011)

Image 56

Contents Flail Shredder Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications Balance Statement General InformationSafety Safety RulesPreparation TrainingTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedPeligro Advertencia Be CarefulOperator Record Operator SIGN-OFF RecordOperation OperationPrincipal Components BREAK-IN of the Flail ShredderHorsepower Tractor WeightPRE-OPERATION Check List Choosing the Correct TractorLoad Sensing Hydraulics 3-Point Models Only PTO Driveline LengthPoint Hitch Cut only the male end. Never cut the female end Attaching Shredder to TractorWith Quick Hitch Attachment Without Quick Hitch Attachment Removing Shredder from TractorRubber Flaps or Belting Preparing for OperationFlail Knives Flail HeightStarting the Shredder Setting Flail HeightSetting Caster Wheels Cleaning Stopping the ShredderHazard Area Ground SpeedDo not exceed 20 MPH while transporting shredder Operation Service & Maintenance Service & MaintenanceLubricants GreasingDaily or every 8 hours of operation Every 25 hours of operationEvery 40 hours of operation Figure AnnuallyHours Lubrication Service Record Hours Serviced byHours or daily Gearbox leakage & Troubleshooting Gearbox OIL LeakageWheel Spacing Acceptable Oil LeakageReplacing Flail Knives Replacing Rubber Shield FlapsServicing Rotors Flail Tubes Removing ComponentsReplacing Components Replacing Stub ShaftIf removing rotor drive coupling, use Loctite No Or equivalent and special high collar lockMounting Clutch to Shredder Removing the DrivelineRebuilding Overrunning Clutch Service & Maintenance Troubleshooting TroubleshootingContour Flail Patterns Worksheet for Contour Flail Patterns24’ Assembly AssemblyWheel Assembly Dealer SET-UP InstructionsFloating Upper Mast Installed Point UnitsManual Storage Tube Installation Rubber Belting InstallationRubber Flap Installation ALL UnitsSafety Light Installation Safety Light Installed Wiring HarnessEND TOW Hitch Installation Optional Equipment Install Center DeflectorCenter CUT KIT Installation Block ShreddedInstall Motor Housing Figure Assemble Motor and Blade FigureAssembly Hoses Motor Assembly InstalledInstall Hose Clamps Install DecalsConnect Hoses to Tractor Remove Deflector KitDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index Flail Shredder PartsCenter Drive Flail Shredder Frame Assembly Center Drive Flail Shredder Frame Assembly Parts List Part QTY DescriptionFlail Tube Assembly Left RightStrut and Caster Assembly END TOW and Safety Light Assembly Weasler 30K 3-POINT PTO Shaft with Automatic Clutch END TOW Assembly and Safety Light Part List Weasler Automatic Clutch Center Drive Gearbox Rubber Belting Hydraulic Hose Assembly Rubber FlapAdvertencia Center Cutter KIT OptionalCenter Cutter KIT Parts List Center Deflector OptionalBolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexWarranty Rev /3/2011 MAN0943 Woods Equipment Company