Dolmar MS-251.4, MS-250.4 instruction manual Refueling, Storageof Machineand Refilltank

Page 13

(1) Keep the engine level, and detach the oil gauge.

(2)Fill oil up to the edge of the oil refill port. (Refer to Fig.2 of the preceding page).

Feed oil with the lubricant refill container.

(3)Securely tighten the oil gauge. Insufficient tightening may cause oil leakage.

Point 2 in Replacement of Oil: “If oil spills out”

If oil spills out between the fuel tank and engine main unit, the oil is sucked into through the cooling air intake port, which will contaminate the engine. Be sure to wipe out spilt oil before start of operation.

REFUELING

Handling of Fuel

It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufficiently ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still irritated, consult your doctor.

Storage Period of Fuel

Fuel should be used up within a period of 4 weeks, even if it is kept in a special container in a well-ventilated shade. If a special container is not used or if the container is not covered, fuel may deteriorate in one day.

STORAGEOF MACHINEAND REFILLTANK

Keep the machine and tank at a cool place free from direct sunshine. Never keep the fuel in the cabin or trunk.

Fuel

The engine is a four-stroke engine. Be sure to use an automobile gasoline (regular gasoline or premium gasoline).

Points for Fuel

Never use a gasoline mixture which contains engine oil. Otherwise, it will cause excessive carbon accumulation or mechanical troubles.

Use of deteriorated oil will cause irregular startup.

Refueling

WARNING: INFLAMMABLES STRICTLY PROHIBITED

Gasoline used: Automobile gasoline (unleaded gasoline)

Loosen the tank cap a little so that there will be no difference in atmospheric pressure.

Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that the refuel port will be oriented upward. (Never refill fuel full to the oil refill port.)

Wipe well the periphery of the tank cap to prevent foreign matter from entering into the fuel tank.

After refueling, securely tighten the tank cap.

If there is any flaw or damage on the tank cap, replace it.

The tank cap is consumable, and therefore should be renewed every two to three years.

Fuel tank cap

Fuel upper limit

Fuel tank

12

Image 13
Contents MS-250.4MS-251.4 Symbols General Instructions Safety InstructionsIntended use of the machine Personal protective equipmentRefuelling Method of operation Maintenance instructionsKickback Kickback preventionNever straighten or weld damaged cutting tools When asking for help, please give the following informationFirst Aid PackagingMS-251.4 MS-250.4 Model Technical Data MS-250.4, MS-251.4MS-250.4 Brush Cutter MS-251.4 String trimmer Designation of PartsFor machines with U Handle models Mounting of HandleFor machines with Loop Handle Mounting of Protector For MS-250.4 with the hex wrench still in place Mounting of Cutter Blade or Nylon Cutter HeadMounting of nylon cutting head Before Start of Operation Point 1 in Replacement of Oil Oil GaugeInspection and Refill of Engine Oil Storageof Machineand Refilltank RefuelingCorrect Handling of Machine Points in Operation and HOW to StopStarting Open For machine with U Handle or Loop HandleResharpening the Cutting Tool Adjustment of LOW-SPEED Rotation IdlingStopping Startup after warm-up operationOperation Nylon Cutting HeadReplacing the nylon cord Daily checkup and maintenance Replacement of Engine OILServicing Instructions Points in Handling Air Cleaner Element Cleaning of AIR CleanerPoints on OIL Replacement of Fuel Pipe Cleaning of Fuel FilterCleaning of Parts Replacement of Gaskets and PackingsStorage Fault locationOperating time Troubleshooting Emission Compliance Period Owners Warranty Responsibilities Manufacturers Warranty CoverageWhat is not Covered What is CoveredHOW to File a Claim Waranty Commencement DateParts Covered Under the California Emission Warranty Where to GET Warranty ServiceMaintenance Statements Repair and Replacement of EMISSION-RELATED Parts Parts Covered Emission Component Defect Warranty PeriodObtaining Warranty Service HOW to Make a Claim Dolmar SymbolesInstructions générales Consignes DE SécuritéUtilisation spéciale de la machine Équipement personnel de protectionMètres RavitaillementMéthode dutilisation Instructions de maintenanceEffet de retour Outils de coupeEmballage Premier secoursMS-251.4 MS-250.4 Modèle Caracteristiques Techniques MS-250.4, MS-251.4Nomenclature DES Pièces MS-250.4 Débroussailleuses MS-251.4 Taille-borduressPour les modèles à polgnée en U Montage DE LA PoignéeMachines à poignée simple Pour MS-250.4 Montage DU Dispositif DE ProtectionPour MS-250.4, MS-251.4 Utilisation du protecteur pour lame métallique/lame à filPour MS-250.4 avec clé hexgonale étant toujours en place Montage DE LA Lame DE Coupe OU DE LA Téte DE Coupe À FILMontage du dispositif de coupe à fil Controle ET Ravitaillement DE L’HUILE Moteur Avant Mise EN MarcheEntrepôsage DE L’APPAREIL ET DU Réservoir DE Ravitallement RavitaillementConsignes DE Mise EN Marche ET Arrêt DE LA Machine Manipulation Correcte DE LA MachineFixation du harnais RetraitFermer Pour les machines à poignée en U ou en BoucleOuvrir Consignes de sécurité lors du fonctionnementReglage DE LA Marche a Petite Vitesse AU Ralenti Réaffûtage DE Loutil DE CoupeVerification DE LA Rotation a Petite Vitesse Tête de coupe à fil en nylon Contrôle et opérations de maintenance réguliers Remplacement DE L’HUILE a MoteurInstructions Relatives AUX Réparations Essentiels Pour L’HUILE Nettoyage DU Filtre À AIRRemplacement DES Joints ET Garnitures Remplacement DU Tuyau a CarburantContôle DE LA Bougie Dallumage Graissage DU Carter D’ENGRENAGELocalisation des défauts RemisageDurée de marche Depannage Lista de contenidos Página SímbolosInstrucciones generales Instrucciones DE SeguridadEquipo Personal de Protección Puesta en Marcha de la Desbrozadora/CortabordesReabastecimiento Contragolpe Método de trabajoHerramientas de Corte Cabezal de NylonPrimeros Auxilios Nunca rectificar o soldar las herramientas de corte dañadasEmbalaje Datos Técnicos MS-250.4, MS-251.41 Cortabordes Denominación DE PartesPara máquinas con manillar en U Montaje DEL ManillarPara máquinas con manillar cerrado USO DE Protector Parahojas METALICAS/CORTADOR DE Cuerda Montaje DEL ProtectorMontaje de la cabeza de corte de nylon Montaje DE LA Hoja DE Corte O Cabezal DE Corte DE NylonInspeccióny Reabastecimientode Aceitedemotor Antes DE Empezar EL TrabajoPunto 1 de reabastecimiento de aceite bayoneta de aceite Almacenaje DE Lamáquinay DEL Tanque DE Reabastecimiento Reabastecimiento DE CombustiblePuntos Relacionados CON EL Manejo Y LA Parada USO Correcto DE LA MáquinaArranque Precauciones durante la operación Máquina con manillar U ó cerradoAjuste DEL Giro a Baja Velocidad Ralentí Afilar LA Herramienta DE CorteArrancar después de la operación de calentamiento CuidadoOperación CabezaldenylonSustitución del cabezal de Nylon Cambio DEL Aceite DEL Motor Instrucciones DE ServicioComprobación y mantenimiento diarios Puntos Relacionados Conel Aceite Limpieza DEL Depurador DE AireManipulación del elemento del filtro de aire Suministro DE Grasa a LA Caja DE Engranajes Comprobación DE LA BujíaLimpieza DEL Filtro DE Combustible Cambio DEL Tubo DE CombustibleAtención después de almacenamiento de largo tirmpo AlmacenamientoLocalizacion de averias Tiempo de Iinvestigación DE Averías Dolmar GmbH Postfach 70 04 Hamburg Germany