Dolmar MS-250.4 Correct Handling of Machine, Points in Operation and HOW to Stop, Starting

Page 14

CORRECT HANDLING OF MACHINE

Attachment of shoulder strap

–Adjust the strap length so that the cutter blade will be kept parallel with the ground.

Detachment

For MS-251.4

–In an emergency, push the notches (1) at both sides, and you can detach the machine from you.

Be extremely careful to maintain control of the machine at this time. Do not allow the machine to be deflected toward you or anyone in the work vicinity.

WARNING: Failure to maintain complete control of the machine at all could result in serious bodily injury or DEATH.

Hanger

For MS-250.4

–In case of emergency, remove the emergency detachment lever (2) by pulling strongly with a finger. The machine sill detach from body.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deflected toward you or	anyone in the work
vicinity.	(2)

WARNING: Failure to maintain complete control of the machine at all could result in serious bodily injury or DEATH.

Hanger

POINTS IN OPERATION AND HOW TO STOP

Observe the applicable accident prevention regulations!

STARTING

Move at least 3m away from the place of refuelling. Place the brush cutter on a clean piece of ground taking care that the cutting tool does not come into contact with the ground or any other objects.

A:Cold start	Throttle control dial

1) Set this machine on a flat space.

I-O switch (1)

Throttle lever (6)

OPERATION

Low speed	Lock-off lever

High speed

13

Image 14

Contents MS-250.4MS-251.4 Symbols Intended use of the machine Safety InstructionsGeneral Instructions Personal protective equipmentRefuelling Kickback Maintenance instructionsMethod of operation Kickback preventionFirst Aid When asking for help, please give the following informationNever straighten or weld damaged cutting tools PackagingTechnical Data MS-250.4, MS-251.4 MS-251.4 MS-250.4 ModelDesignation of Parts MS-250.4 Brush Cutter MS-251.4 String trimmerFor machines with Loop Handle Mounting of HandleFor machines with U Handle models Mounting of Protector Mounting of nylon cutting head Mounting of Cutter Blade or Nylon Cutter HeadFor MS-250.4 with the hex wrench still in place Inspection and Refill of Engine Oil Point 1 in Replacement of Oil Oil GaugeBefore Start of Operation Refueling Storageof Machineand RefilltankStarting Points in Operation and HOW to StopCorrect Handling of Machine For machine with U Handle or Loop Handle OpenStopping Adjustment of LOW-SPEED Rotation IdlingResharpening the Cutting Tool Startup after warm-up operationReplacing the nylon cord Nylon Cutting HeadOperation Servicing Instructions Replacement of Engine OILDaily checkup and maintenance Points on OIL Cleaning of AIR CleanerPoints in Handling Air Cleaner Element Cleaning of Parts Cleaning of Fuel FilterReplacement of Fuel Pipe Replacement of Gaskets and PackingsFault location StorageOperating time Troubleshooting Emission Compliance Period Manufacturers Warranty Coverage Owners Warranty ResponsibilitiesHOW to File a Claim What is CoveredWhat is not Covered Waranty Commencement DateMaintenance Statements Where to GET Warranty ServiceParts Covered Under the California Emission Warranty Repair and Replacement of EMISSION-RELATED Parts Emission Component Defect Warranty Period Parts CoveredObtaining Warranty Service HOW to Make a Claim Symboles DolmarUtilisation spéciale de la machine Consignes DE SécuritéInstructions générales Équipement personnel de protectionRavitaillement MètresEffet de retour Instructions de maintenanceMéthode dutilisation Outils de coupePremier secours EmballageCaracteristiques Techniques MS-250.4, MS-251.4 MS-251.4 MS-250.4 ModèleMS-250.4 Débroussailleuses MS-251.4 Taille-borduress Nomenclature DES PiècesMachines à poignée simple Montage DE LA PoignéePour les modèles à polgnée en U Pour MS-250.4, MS-251.4 Montage DU Dispositif DE ProtectionPour MS-250.4 Utilisation du protecteur pour lame métallique/lame à filMontage du dispositif de coupe à fil Montage DE LA Lame DE Coupe OU DE LA Téte DE Coupe À FILPour MS-250.4 avec clé hexgonale étant toujours en place Avant Mise EN Marche Controle ET Ravitaillement DE L’HUILE MoteurRavitaillement Entrepôsage DE L’APPAREIL ET DU Réservoir DE RavitallementFixation du harnais Manipulation Correcte DE LA MachineConsignes DE Mise EN Marche ET Arrêt DE LA Machine RetraitOuvrir Pour les machines à poignée en U ou en BoucleFermer Consignes de sécurité lors du fonctionnementVerification DE LA Rotation a Petite Vitesse Réaffûtage DE Loutil DE CoupeReglage DE LA Marche a Petite Vitesse AU Ralenti Tête de coupe à fil en nylon Instructions Relatives AUX Réparations Remplacement DE L’HUILE a MoteurContrôle et opérations de maintenance réguliers Nettoyage DU Filtre À AIR Essentiels Pour L’HUILEContôle DE LA Bougie Dallumage Remplacement DU Tuyau a CarburantRemplacement DES Joints ET Garnitures Graissage DU Carter D’ENGRENAGERemisage Localisation des défautsDurée de marche Depannage Símbolos Lista de contenidos PáginaEquipo Personal de Protección Instrucciones DE SeguridadInstrucciones generales Puesta en Marcha de la Desbrozadora/CortabordesReabastecimiento Herramientas de Corte Método de trabajoContragolpe Cabezal de NylonEmbalaje Nunca rectificar o soldar las herramientas de corte dañadasPrimeros Auxilios Datos Técnicos MS-250.4, MS-251.41 Denominación DE Partes CortabordesPara máquinas con manillar cerrado Montaje DEL ManillarPara máquinas con manillar en U Montaje DEL Protector USO DE Protector Parahojas METALICAS/CORTADOR DE CuerdaMontaje DE LA Hoja DE Corte O Cabezal DE Corte DE Nylon Montaje de la cabeza de corte de nylonPunto 1 de reabastecimiento de aceite bayoneta de aceite Antes DE Empezar EL TrabajoInspeccióny Reabastecimientode Aceitedemotor Reabastecimiento DE Combustible Almacenaje DE Lamáquinay DEL Tanque DE ReabastecimientoArranque USO Correcto DE LA MáquinaPuntos Relacionados CON EL Manejo Y LA Parada Máquina con manillar U ó cerrado Precauciones durante la operaciónArrancar después de la operación de calentamiento Afilar LA Herramienta DE CorteAjuste DEL Giro a Baja Velocidad Ralentí CuidadoSustitución del cabezal de Nylon CabezaldenylonOperación Comprobación y mantenimiento diarios Instrucciones DE ServicioCambio DEL Aceite DEL Motor Manipulación del elemento del filtro de aire Limpieza DEL Depurador DE AirePuntos Relacionados Conel Aceite Limpieza DEL Filtro DE Combustible Comprobación DE LA BujíaSuministro DE Grasa a LA Caja DE Engranajes Cambio DEL Tubo DE CombustibleLocalizacion de averias AlmacenamientoAtención después de almacenamiento de largo tirmpo Tiempo de Iinvestigación DE Averías Dolmar GmbH Postfach 70 04 Hamburg Germany