Marantz SR6003 manual ‹4 ‹5, English

	ENGLISH
NAMES AND FUNCTION	¤0 Numeric buttons
	These buttons are used to switch between 0 to +10
	of the source components.
	If the source is set to the amplifier, these buttons are
	used to perform operations.
	(When AMP mode is selected)
BASIC CONNECTIONS	1/AUTO button
	This button is used to select auto surround.
	2/STEREO button
	This button is used to select STEREO mode.
	3/P.DIRECT button
	When this button is pressed once, SOURCE DIRECT
BASIC	mode is selected.
	If pressed again, PURE DIRECT mode is selected.
	4/SLEEP button
	This button is used for setting the sleep timer.

¤4 DISPLAY button

(When a mode other than DMP (USB) is selected) This button is used to selects the display mode for the front display of the unit.

(When DMP mode (USB) is selected)

This button is used to select the previous page.

¤5 INPUT 3 button

This button is for forward-feeding the input source to select a desired source.

INPUT 4 button

This button is for backward-feeding the input source to select a desired source.

¤6 SETUP button

¤9 A/D button

This button is used to switch between the analog and digital inputs.

‹0 HDMI button

This button is used to select HDMI OUTPUT 1 or 2.

‹1 SET button

This button is used to enter learn mode and preset mode.

‹2 / SOURCE ON/OFF button

This button is used to turn a specific source (such as a DVD player) on or off independently from the rest of the system.

‹4 ‹5 ‹6 ‹7

‹4 LEARN indicator

This indicator is displayed when the remote controller is in the LEARN mode.

‹5 MACRO indicator

This is displayed when a macro program is selected by the remote controller.

OPERATION	5/M-DAX button
	This button is used to select M-DAX mode.
	6/EQ button
ADVANCED CONNECTIONS	This button is used to select Audyssey mode.
	7/LIP SYNC button
	This button is used to select LIP SYNC mode.
	8/NIGHT button
	Pressing this button prevents the Dolby Digital signal
	from playback at a loud voice.
	When this button is pressed, the “NIGHT” indicator
	is illuminated.
SETUP	9/V.OFF buton
	This button is used to turn off the video signal.
	0/CH SEL button
	This button is used to call up CH LEVEL ADJUST
	and adjust speaker levels or 7.1 ch input level.
ADVANCED OPERATION	¤1 M (MACRO) button
	This button is used to program Macros. Pressing this
	button switches between Normal mode and Macro
	mode.
TROUBLESHOOTING	¤2 MENU button
	(When AMP mode is selected)
	This button is used to call up the SETUP MAIN
	MENU of the unit.
	¤3 TOP button
	Pressing this button during setup returns you to the
	top screen of the setup main menu.
OTHERS

This button is used to setup for DVD and other device.

¤7 SOURCE button

These buttons are used to switch the source of your A/V Receiver. Each time a source button is pressed, the remote controller changes to the source which was pressed.

This remote controller can control 12 types of equipment. To change the A/V Receiver source, press this button twice within two seconds.The signal is sent when it is pressed the second time.

Notes:

•Select the AMP as the source to use this remote controller with the unit.

•In the case of the unit, the DMP button cannot be used.

¤8 ATT. button

When the input signal is too high and the voice distorts even by throttling the unit VOLUME control, turn on this function.

“ATT” is indicated when this function is activated. The input level reduced. Attenuator is invalid for the output signal of “REC OUT”.

Note:

This function is unavailable while the digital input is selected.

‹3 Infrared Transmitter and Learning

Sensor

This transmitter emits infrared light. Press the buttons while pointing the transmitter towards the infrared receiver window of the unit or other AV equipment. Be sure to also point towards other remote controllers when using the learning function.

‹6 Information indicator

Information about the sources and modes are shown on the LCD.

‹7 indicator

This indicator is displayed when the remote controller is transmitting a signal.

8