FUNCTION | NAMES AND |
CONNECTIONS | BASIC |
BASIC OPERATION | |
CONNECTIONS | ADVANCED |
SETUP | |
OPERATION | ADVANCED |
TROUBLESHOOTING | |
OTHERS | |
ENGLISH
M-DAX (Marantz Dynamic Audio eXpander)
This function makes up for lost audio content in MP3 or AAC sources (from lossy compression) during playback. Choose one of the following levels for this effect as desired.
“HIGH”: Stronger effect
“LOW”: Weaker effect
“OFF”: Deactivated.
(Using the remote controller)
When switching to
Press the
Each time this button is pressed,
OFF 
LOW 
HIGH
The
when
Notes:
•
•The
ATTENUATION TO ANALOG INPUT SIGNAL
If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on
the remote controller.
“ATT” indicator will be illuminated when this function is activated. The
This function is memorized for each individual input source.
SPEAKER A/B
This unit has speaker
You can select these systems by pressing SPKR A/B on the remote controller.
Press the SPKR A/B button.
Each time this button is pressed, Speaker system A
and B changes as follows.
A 
B 
A+B 
OFF
7.1 CH INPUT
This unit is equipped for future expansion through the use of Multi channel Super Audio CD multichannel player or
When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and right), center, surround (left and right) and surround back speaker systems as well as the
In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video sources
2.
4.
1.
4.
3.
1. Select a desired Video source to decide the routed video signal to the Monitor Outputs.
2. Press the 7.1 button on the remote controller to switch the 7.1 channel input.
3. If it is necessary to adjust the output level of each channel, press the CH.SEL button on the remote controller.
Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between
The subwoofer can be adjusted between
These adjustments result will be stored to 7.1 CH. INPUT memory.
4. Adjust the main volume with the MAIN VOLUME knob or the VOL buttons on the
remote controller.
To cancel the 7.1 CH. INPUT setting, press the 7.1 button on the remote controller.
Notes:
•When the 7.1 CH. Input is in use, you may not select a surround mode, as the external decoder determines processing.
•In addition, there is no signal at the record outputs when the 7.1 CH. Input is in use.
•Furthermore, the following functions are not available during 7.1 CH Input use.
Test Tone, NIGHT MODE, Source Direct, Pure Direct,
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder,
L(front left) and R (front right) inputs terminals are available as AUX2 input.
In this case, You can connect additional audio source to AUX2 as other audio input terminals.
VIDEO ON/OFF
When no video signal is connected to the unit or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, press the AMP button and press
the V.OFF button.
The
light.
44