English, Ch Input Setup, Mode, Digital, Hdmi, Comp

1-1 FUNCTION INPUT SETUP

(ASSIGNABLE DIGITAL INPUT)

The 5 and F (Front) digital inputs can be assigned to a desired source.

HDMI and COMPONENT inputs can be assigned to the preferred source.

Use this menu to select which digital input jacks are to be assigned to which input source.

1. Select “Function Input Setup” from the Input Setup menu with the 3 or 4 cursor buttons and press the ENTER button.

Function Input Setup
Function	Mode	Digital	HDMI	Comp.		S / Video
TV	Auto	1	1	1		1
DVD	Auto	2	2	2		2
VCR	Auto	3	3	3		3
DSS	Auto	4	-	-		4
AUX1	Auto	F	-	-		*
TAPE	Auto	-	-	-		1
CD/R	Auto	5	-	-		2
AUX2	Auto	-	-	-		3
SIRIUS	Analog	-	*	*		*
Return
: Up / Down	:		Enter : Return		Exit : Exit

2. Select a setting with the 3, 4, 1, and 2 cursor buttons, and assign a mode and input jack (Digital, HDMI, Comp, S/Video).

MODE

Auto:

Select “Auto”, for automatic detection of the digital input signal condition.

If there is no digital signal, but there is an analog signal present, the analog signal will be played. “Auto” is the initial setting of all input sources.

HDMI:

Select “HDMI”, when only a HDMI signal will be used.

Digital:

Select “Digital”, when only a digital signal will be used.

Analog:

Select “Analog” for input sources for which no digital input jacks are used.

Digital

5 and F(Front) digital inputs can be assigned to a desired source.

Assign the number of a digital input jack to the device.

HDMI

Assign the number of an HDMI input jack to the device.

Note:

•When FUNCTION MODE is set to HDMI and HDMI AUDIO of “5. PREFERENCE” is set to Through, audio is not output from the unit. (See page 38)

Comp

Assign the number of a component video input jack to the device.

S/Video

Assign the number of a composite video and S- video input jack to the device.

Note:

•Video and S-video can use the same numbers when assigning to input functions.

•The ✽ mark in AUX1 indicates that other inputs cannot be assigned.

3.Press the ENTER button.

4.Select each mode setting and input terminal with the 1 or 2 cursor buttons.

5.Press the ENTER button.

6.Repeat steps 2-5 until all items are set.

Note:

•Assignments cannot be made in sections with a ✽ mark.

1-2 7.1 CH INPUT SETUP

This menu is for adjusting the speaker levels for 7.1- channel input sources.

Here you will adjust the volume for each channel so that they are all heard by the listener at the same level.

1. Select “7.1 ch Input Setup” from the Input Setup menu with the 3 or 4 cursor buttons and press the ENTER button.

7.1ch Input Setup
Video-in		: Last
Front Left		: 0.0dB
Center		: 0.0dB
Front Right		: 0.0dB
Surround Right		: 0.0dB
Surround Back Right		: 0.0dB
Surround Back Left		: 0.0dB
Surround Left		: 0.0dB
Subwoofer		: 0.0dB
Return
: Up / Down	: Change	Enter :	Exit : Exit

2. Select “Video-in” with the 3 or 4 cursor buttons.

3. Using the 1 or 2 cursor buttons, select the video input source to be played through the MONITOR OUT jack.

The input source is switched by pressing the 1 or 2 cursor buttons as follows;

Last ↔ TV ↔ DVD ↔ VCR ↔ DSS ↔ AUX1 ↔ TAPE ↔ CD/R ↔ AUX2 ↔ Video-off ↔ Last ↔...

Notes:

•When “Last” is selected, the source is set to the source selected before the 7.1 ch input menu was activated.

•When “Video-off” is selected, no signal is emitted from MONITOR OUT jack.

4.Select desired channel with the 3 or 4 cursor buttons.

5.Using the 1 or 2 cursor buttons, adjust the volume level of each channel.

Move the cursor to “Return” with the 3, 4, 1, and 2 cursor buttons, and press the ENTER button to go to the Input Setup menu.

Note:

•The volume level can be set between -12 dB and +12 dB in 1 dB increments on all channels except the subwoofer (SUB W), which can be set from -18dB to +12 dB in 1 dB increments.

ENGLISH

NAMES AND	FUNCTION
BASIC	CONNECTIONS
BASIC OPERATION
ADVANCED	CONNECTIONS
SETUP
ADVANCED	OPERATION
TROUBLESHOOTING
OTHERS