Marantz SR6003 manual Advanced Operation, Display Mode, Recording An Analog Source, Others, Notes

ENGLISH

ADVANCED OPERATION

ANDNAMES FUNCTION	AMP OPERATION
	USING THE SLEEP TIMER							DISPLAY MODE
BASIC CONNECTIONS
BASIC
OPERATION	To program this unit for automatic standby, press the							You can select the display mode for the front display
	SLEEP button on the remote controller.
								of the unit.
	Each press of the button will increase the time before
								To select this mode, press the DISPLAY on the
	shut down in the following sequence.
								remote controller or the front panel.
ADVANCED CONNECTIONS
								When this button is pressed, the display mode is
	OFF	10		20	30	40	50	switched in the following sequence.
	120	110	100	90	80	70	60	Normal → Volume → Auto display OFF → Display
								OFF → Normal Mode
	The sleep time will be shown for a few seconds in the							Normal mode:
	display on the front panel, and it will count down until
								The following three mode types are displayed.
	the time has elapsed.
								•	Displays the selected input function. If the
	When the programmed sleep time has elapsed, the
SETUP									function has been renamed using the Function
	unit will automatically turn off.
									Rename feature (see page 28), the renamed
	Note that the SLEEP indicator on the display will
									name appears on the display.
	illuminate when the Sleep function is programmed.							•
									Displays the input mode set via the Function
	To cancel the Sleep function, press the SLEEP								Input Setup feature. (See page 27)
	button until the display shows “SLEEP OFF” and the							•
									Displays the status of the selected surround
ADVANCED OPERATION	SLEEP indicator will disappear.								mode.
								Volume mode:
								The input function and input mode are displayed
								in the upper part, and the current volume level is
								displayed in the lower part.
								Auto Display Off mode:
								The display is off. But, if you make a change to
TROUBLESHOOTING								the unit such as the input or surround mode, the
								display will show that change, then go back to off
								after about 3 seconds.When changing the volume,
								it is not displayed.
								Display Off mode:
								The display is off completely.
								Note:
									• Only the “DISP” indicator will be illuminated on the
OTHERS									front display in display off condition.

42

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source selected for listening through this unit is sent to the record outputs.

This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD/CDR OUT and VCR OUT in the record mode.

To record the input source signal you are currently watching or listening to

1.

1.

1. Select the input source to record by turning the INPUT SELECTOR knob on the front panel or simply press the input selector buttons on the remote controller.

The input source is now selected and you may watch or listen to it as desired.

2. The currently selected input source signal is output to the TAPE OUT, CD/CDR OUT and VCR OUT outputs for recording.

3. Start recording to the recording component as desired.

Notes:

•When connecting only digital signal input, output cannot be made to the TAPEOUT, CD/CDR OUT or VCR OUT terminals. When using recording functions, be sure to also make connections for analog signal input.

•No conversion is made from Video signal input to S-Video signal output or from S-Video signal input to Video signal output. Always use the same signal type for both input and output.

•Video or audio signals input to HDMI input terminals cannot be recorded.

SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT

If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source as following procedures.

Press the AMP button and press the A/D button. When this button is pressed, the input mode is switched in the following sequence.

Auto → HDMI → Digital → Analog → Auto

Auto mode:

The types of signals being input to the digital and analog input jacks for the selected input source are detected automatically.

If no digital signal is being input, the analog input jacks are selected automatically.

HDMI mode:

HDMI mode can be selected only when an HDMI input has been assigned as an input source. When “HDMI Audio” under Preference of the Setup Menu is set to “Through”, the HDMI mode cannot be selected.

Digital mode:

The input signal is fixed to an assigned digital input terminal.

Analog mode:

The analog input jacks are selected.

This selection is temporary and will not be stored in memory.

To store changes to the input mode, select “Input Setup” from the Main Menu. (See page 27)