Husqvarna manual ZTH5223 ZTH6125, Fuel capacity Litres 11.4 US Gal., 22 litres

Page 10

TECHNICAL DATA

Model

ZTH5223

ZTH6125

Displacement

10.2 cc/r (0.623 cu. in./rev)

10.2 cc/r (0.623 cu. in./rev)

Nominal working pressure

70 bars (1000 PSI)

70 bars (1000 PSI)

Max. hydraulic pressure

145 bars (2,100 PSI)

145 bars (2,100 PSI)

Max. hydraulic oil temp

110°C (230°F)

110°C (230°F)

Weight, hydraulic pump

3.6 kg (8 lbs)

3.6 kg (8 lbs)

Hydraulic motors (2)

Parker Ross

Parker Ross

Tightening torque, wheel motor

122 Nm (90 ft/lb)

122 Nm (90 ft/lb)

hub nut

 

 

Hydraulic oil

1.9 litres (2 qt.), 15W-50

1.9 litres (2 qt.), 15W-50

 

Synthetic

Synthetic

Hydraulic oil cooler

Yes

Yes

Speed forward

Variable, max. 12.9 km/h

Variable, max. 12.9 km/h

 

(8 mph)

(8 mph)

Speed reverse

Variable, max. 3.23 km/h

Variable, max. 3.23 km/h

 

(2 mph)

(2 mph)

Rear tires

Carlisle 24" X 12.00 - 12 Tubeless

Carlisle 24" X 12.00 - 12 Tubless

 

Turf Master

Turf Master

Tightening torque, lug nuts

100 Nm (75 ft/lb)

100 Nm (75 ft/lb)

Front tires

Carlisle 13" X 5.00 - 6 Tubeless

Carlisle 13" X 5.00 - 6 Tubeless

Electrical system

12 V with 15 A charging system

12 V with 15 A charging system

Fuel capacity

44 litres (11.4 US Gal.), 22 litres/

44 litres (11.4 US Gal.), 22 litres/

 

tank

tank

Seat

Adjustable, high-back seat with

Adjustable, high-back seat with

 

armrests

armrests

Overall length

2057 mm (81 in.)

2057 mm (81 in.)

Overall width (chute up)

1346 mm (53 in.)

1575 mm (62 in.)

Overall width (chute down)

1600 mm (63 in.)

1829 mm (72 in.)

Overall height

1073 mm (42.25 in.)

1073 mm (42.25 in.)

Weight

464.5 kg (1024 lbs.)

464.5 kg (1024 lbs.)

Tightening torque, standard

 

 

bolts

 

 

1/4"

12 Nm (9 ft/lb)

12 Nm (9 ft/lb)

5/16"

25 Nm (18 ft/lb)

25 Nm (18 ft/lb)

3/8"

44 Nm (33 ft/lb)

44 Nm (33 ft/lb)

English-8

Image 10
Contents ZTH Svenska Contents Workshop Manual RIDE-ON Lawn Mower ZTHEnglish-2 General Instructions Safety InstructionsSafety Instructions Special InstructionsSafety Regulations Explanation of Symbols Explanation of SymbolsXxxxxxx xxxx xxxxxxxx xxx x. xxxx xxxxxx Tools ToolsZTH5223 Technical DataTechnical Data ZTH6125Tightening torque, standard Bolts ZTH5223 ZTH6125Fuel capacity Litres 11.4 US Gal., 22 litres 12 Nm 9 ft/lb 25 Nm 18 ft/lb 44 Nm 33 ft/lbAccessories 70 Nm 52 ft/lb 110 Nm 80 ft/lbEnglish-10 Pre-delivery Service Delivery and Dealer ServiceDelivery and Dealer Service Charge the battery Mount the rear tiresAfter the First 8 Hours Hour ServiceCarry out a 25 hour service Change the motor oilEnglish-13 At Least Once a Year Maintenance Schedule Daily Weekly Service Records English-18 To our Dealers Delivery ServicingDelivery Servicing Removing the Mower from its PackagingDelivery Service Risk of incorrect assembly/fitting Important InformationADD Gasoline is highly flammable Take great care Administration Test RunningGeneral Design and FunctionDesign and Function Mower IdentificationEngine identification Drive and Control EngineBrakes Mower Deck Belt is automatically adjusted by a springWith the belt and the other pulleys Removing RepairsRepairs Disconnect the cable from the starter motorFitting Adjusting Throttle Lever Tension Adjusting the Throttle WireChecking and Adjusting the Throttle Wire Checking and Adjusting the Choke Wire DiagramThree nuts 10 all with washers Fuel tankFire and health hazard Avoid spills Wipe dry if necessary Springs 9 located on the underside of the splashguardAdjusting the Park Brake Adjusting Motion Control Lever LinkagesAdjusting Motion Control Lever Spring-back See Hydraulic system\Hydraulic pump\Adjusting the linkagesZTH mower deck diagram Removing Bearings Repairing BearingsSpindle Blade Bearings Roll the belt off see Changing BeltsReplacing Bearings Sharpening and Balancing BladesOr any other damage. If they do, scrap Deck Belt Setting the Mower DeckAdjusting Cutting Height LevelingBelt Tensioning Assembly Hydraulic Pump Belt Changing Pump and Deck BeltsDismantling Pump Belt Tensioning AssemblyFront Wheel Bearings AssemblingEnglish-42 Diagram below shows the structure of the electrical system TroubleshootingWiring Assembly Electrical SystemZTH console harness ZTH frame harness Refer to the ZTH electrical system diagram BatteryFuses Starter Motor Contactor RelaysChanging Ignition and Start Switch Hour MeterMower Deck Clutch Blade SwitchTroubleshooting Guide Measuring the Supply VoltageMotion Control Switches Park Brake Interlock Switch Check that the start interlock functions correctlyWelding Hydraulic System Hydraulic SystemHydraulics Hygiene Correct Oil Leaks Keep Hydraulic Oil CleanHydraulic Oils Work MethodsZTH Hydraulic System Draining Hydraulic TankFilling Hydraulic Filter fitting procedure is the reverse of the removal procedureCooler for the Hydraulic System Hydraulic LinesHydraulic Pump Dismantling and Assembling FittingReverse Spring Detent Adjustment Stop the engine and remove the keyHydraulic Motors Dismantling and AssemblingTroubleshooting TroubleshootingWiring Harness To RUN? Clutch Large more than Useful life 125/3.18 mm Problem Possible causes Clutch will not engageSolution Brake will not engageNoisy clutch/vibrations Faulty. Repair or replaceFailed bearing Loose mounting bolt not tightened Troubleshooting Checklist, Hydraulic Pump Problem Cause Corrective actionEspecially the cooler ´+H¶6D¨ Svenska ´+H¶6D¨ 2002W20 Also See