Husqvarna ZTH6125, ZTH5223 manual Daily Weekly

Page 18

DELIVERY AND DEALER SERVICE

 

 

Daily

Weekly

At

Maintenance intervals

 

 

 

 

 

least

in hours

 

 

 

 

 

once

 

Maintenance

Page Pre-

After

 

25 50 100 300

 

a

 

 

use

use

 

 

 

 

 

year

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check/adjust the cutting height regulator.

38

 

 

 

 

Clean the air cleaner’s pre-filter (Oil-foam).

-

 

 

 

Clean the air cleaner’s filter 2) (paper filter).

-

 

 

 

Change the motor oil 1) .

22

 

 

 

Change the hydraulic oil (every 300 hours).

56

 

 

 

Change the engine’s oil filter (every 200 hours).

-

 

 

 

Clean/change the spark plugs.

-

 

 

 

Change the fuel filter in the fuel line.

-

 

 

 

Clean the cooling fins.

-

 

 

 

Check the play in the engine valves 4) .

-

 

 

 

Change the air cleaner’s pre-filter (Oil-foam).

-

 

 

 

Change air filter (paper filter) 2) (every 200 hours).

-

 

 

 

Carry out a 300 hour service 4) .

13

 

 

 

Check/adjust the park brake.

34

 

 

 

1)First change after 8 hours. With heavy operating conditions or high ambient temperature, change every 50 hours. 2) In dusty conditions, clean and change more frequently. 3) Where the mower is in daily use, lubrication must be carried out twice a week. 4) To be carried out by an authorized workshop.

= Covered in this workshop manual.

= Not coverd in this workshop manual or the Operating Instructions.

= Covered in the Operating Instructions.

WARNING!

Service procedures may only be carried out on the motor or mower deck when:

• The motor has been switched off.

The ignition key has ben removed.

The ignition cables have been removed from the spark plugs.

The park brake has been applied.

The mower deck has been disengaged.

English-16

Image 18
Contents ZTH Svenska Contents Workshop Manual RIDE-ON Lawn Mower ZTHEnglish-2 General Instructions Safety InstructionsSafety Instructions Special InstructionsSafety Regulations Explanation of Symbols Explanation of SymbolsXxxxxxx xxxx xxxxxxxx xxx x. xxxx xxxxxx Tools ToolsZTH5223 Technical DataTechnical Data ZTH6125Tightening torque, standard Bolts ZTH5223 ZTH6125Fuel capacity Litres 11.4 US Gal., 22 litres 12 Nm 9 ft/lb 25 Nm 18 ft/lb 44 Nm 33 ft/lbAccessories 70 Nm 52 ft/lb 110 Nm 80 ft/lbEnglish-10 Pre-delivery Service Delivery and Dealer ServiceDelivery and Dealer Service Charge the battery Mount the rear tiresAfter the First 8 Hours Hour ServiceCarry out a 25 hour service Change the motor oilEnglish-13 At Least Once a Year Maintenance Schedule Daily Weekly Service Records English-18 To our Dealers Delivery ServicingDelivery Servicing Removing the Mower from its PackagingDelivery Service Risk of incorrect assembly/fitting Important InformationADD Gasoline is highly flammable Take great care Administration Test RunningGeneral Design and FunctionDesign and Function Mower IdentificationEngine identification Engine Drive and ControlBrakes Belt is automatically adjusted by a spring Mower DeckWith the belt and the other pulleys Removing RepairsRepairs Disconnect the cable from the starter motorFitting Adjusting the Throttle Wire Adjusting Throttle Lever TensionChecking and Adjusting the Throttle Wire Checking and Adjusting the Choke Wire DiagramThree nuts 10 all with washers Fuel tankFire and health hazard Avoid spills Wipe dry if necessary Springs 9 located on the underside of the splashguardAdjusting the Park Brake Adjusting Motion Control Lever LinkagesAdjusting Motion Control Lever Spring-back See Hydraulic system\Hydraulic pump\Adjusting the linkagesZTH mower deck diagram Removing Bearings Repairing BearingsSpindle Blade Bearings Roll the belt off see Changing BeltsSharpening and Balancing Blades Replacing BearingsOr any other damage. If they do, scrap Deck Belt Setting the Mower DeckAdjusting Cutting Height LevelingBelt Tensioning Assembly Hydraulic Pump Belt Changing Pump and Deck BeltsDismantling Pump Belt Tensioning AssemblyFront Wheel Bearings AssemblingEnglish-42 Diagram below shows the structure of the electrical system TroubleshootingWiring Assembly Electrical SystemZTH console harness ZTH frame harness Battery Refer to the ZTH electrical system diagramFuses Relays Starter Motor ContactorChanging Ignition and Start Switch Hour MeterMower Deck Clutch Blade SwitchTroubleshooting Guide Measuring the Supply VoltageMotion Control Switches Park Brake Interlock Switch Check that the start interlock functions correctlyWelding Hydraulic System Hydraulic SystemHydraulics Hygiene Correct Oil Leaks Keep Hydraulic Oil CleanHydraulic Oils Work MethodsZTH Hydraulic System Hydraulic Tank DrainingFilling Hydraulic Filter fitting procedure is the reverse of the removal procedureCooler for the Hydraulic System Hydraulic LinesHydraulic Pump Dismantling and Assembling FittingReverse Spring Detent Adjustment Stop the engine and remove the keyHydraulic Motors Dismantling and AssemblingTroubleshooting TroubleshootingWiring Harness To RUN? Clutch Large more than Useful life 125/3.18 mm Problem Possible causes Clutch will not engageSolution Brake will not engageFaulty. Repair or replace Noisy clutch/vibrationsFailed bearing Loose mounting bolt not tightened Troubleshooting Checklist, Hydraulic Pump Problem Cause Corrective actionEspecially the cooler ´+H¶6D¨ Svenska ´+H¶6D¨ 2002W20 Also See