Dual T1/PRI | 3Com specification

Dual T1/PRI

®

Network Application Card

Product Reference

Version 3.1

http://www.3com.com/

Part No. 1.024.1367-01

Image 2

3Com manual Dual T1/PRI

Contents

Dual T1/PRI Version Number Dual T1/PRI 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Configuring the span line’s interface ID Dual T1/PRI Maintenance Trouble Clearing Page Information This Reference About this ReferenceFinding Specific If you are looking for Turn to Icon Description ConventionsThis table lists conventions used throughout this reference Overview Supported FeaturesAccessing User Interface Callout # Lines 1 Dual T1/PRI ConfigurationConfiguring Span Interface UI console’s main menu Menu Option 2 Configuring the span line’s line coding Menu Option 1 Configuring the span line’s framing modeFraming mode selects the T1 format This diagram represents this process Menu Option 4 Configuring the span line’s jitter attenuation Menu Option 6 Configuring for the Telco’s switch type Menu Option 7 Configuring the span line’s idle bit pattern Menu Option 8 Mapping the span line’s DS0s to chassis modems DS0#sl#/ch# Menu Option 11 Configuring span level call-type blocking Menu Option 9 Configuring the span line’s signaling channelMenu Option 10 Configuring the span line’s interface ID Menu Option 12 Configuring span level cause codes Following types of cause codes are supported Menu Option 13 Configuring the DS0 level call-type blockingCause Code Type Default Cause Code Value Description DSS DS0#, DS0#, DS0#-DS0#,... for multiple DS0s Menu Option 14 Configuring the DS0 level service stateMenu Option 15 Configuring the Short Haul NIC line length Any changes made will take effect immediately Routing ConfiguringInbound Call Menu Option 1 Selecting a Gateway to process digital calls Configuring inbound call routing PHIDX#ph=PH#,ct=x IDP# Use the following syntax to assign a pool type to a pool ID Idpt Card Menu Option 1 Saving configuration changes to NvramSaved to Nvram will be restored Menu Option 9 Allowing ISDN-GWC termination Menu Option 5 Configuring chassis slot devices Menu Option 2 Restoring configuration from NvramMenu Option 3 Restoring the default configuration Menu Option 4 Assigning timing source priority Menu Option 8 Enabling automatic DS0 state change Menu Option 6 Configuring the modem routing methodMenu Option 7 Configuring the UI console password Configuring Software Fault Event Logging Menu Option 9 Companding Code Configuration Commands and logging out of the user interface UI console Dual T1/PRI MaintenanceCommands Dual T1/PRI Issuing this command reboots the NAC Menu Option 1 Resetting the highest priority timing sourceMenu Option 2 Resetting the PRI NAC Selecting option 1 from the main menu produces this screen Menu Options Forcing receiver reframe on the span linesForcing the NAC to master the TDM bus Changing span line service state Menu Option 11 Disabling red Alarm LEDsChanging individual DS0 service states Connect/disconnect B-channel on span lines 1 Logging Out Command, from the console’s main menuFeature in the card configuration option of the main menu UI Console Displays Dual T1/PRI Status DisplaysDual T1/PRI Status From the user interface UI console’s main menu Menu Option 1 Checking power-up self test status RAM Menu Option 2 Checking the T1/PRI’s overall status Menu Option 3 Checking chassis slot device configurationsNo NAC is installed and assigned to that particular slot Menu Option 4 Checking DS0/modem channel status Menu Option 5 Checking the chassis’ Isdn gateway status Checking span line 1 and 2’s DS0 status NetServer PRI NAC Checking span line 1 and 2’s alarm/event statusTime slot is available and awaiting a call Time slots are mapped to Dual T1/PRI Status Displays 8CHAPTER 4 Dual T1/PRI Status Displays Press Ctrl-Rto reset any of the counters on this screen Trouble Clearing Using the LEDsIndicate line signal conditions Trouble clearing information CD 1 or Alrm 1 or Lpbk 1 or T1 Condition LED Color Alarm Severity ResultLevels Layer 2 D-channel Status Correcting Alarm/Error Conditions Alarm/Error Level Trouble Clearing Off and signaling Channel Down Current Draw Technical SpecificationsCertification Regulatory United States Compliance Shipping and Storage Physical DimensionsEnvironment Operating Index Certification B-1 INDEX-2