Clearing Applying System Configuration Settings | 3Com WL-560

28CHAPTER 3: CONFIGURING THE BRIDGE

Table 8 Connection Status Page (continued)

Current Channel	The channel over which the Bridge	Varies
	is communicating with clients.
Security	The type of security for which the	Open System
	Bridge is configured.	(no security)
Rx Data Rate (Mbps)	The most recent data reception	N/A
	rate.
Tx Data Rate (Mbps)	The most recent data transmission	N/A
	rate.
Link Quality	The normalized transmitted data	N/A
	rate (that is, the current data rate
	over the maximum data rate).
	Note: Link Quality is shown in
	Infrastructure mode only.
Received Signal	The strength of the radio signal	N/A
Strength	that the Bridge detects.
	Note: Received Signal Strength is
	shown in Infrastructure mode only.
Activity (Packets Rx)	The number of packets the Bridge	N/A
	has received.
Activity (Packets Tx)	The number of packets the Bridge	N/A
	has transmitted.
IP Address	The IP address of the Bridge.	Varies

Clearing and

Applying System

Configuration

Settings

The pages in the Configuration Management System have two buttons: Clear and Apply.

■Clear returns the settings to the values they were when you last clicked Apply.

■Apply stores the settings permanently in the nonvolatile flash memory. After you click Apply, the new settings take effect and you can see the changes on the System Summary page.

CAUTION: Your changes are lost if you forget to click Apply before

moving to a new configuration page.

Image 34

3Com WL-560 manual Clearing Applying System Configuration Settings, Moving to a new configuration

Contents

3Com 11a/b/g Wireless Workgroup Bridge User Guide 3Com Corporation Campus Drive Marlborough MA USA Contents Configuring the Bridge END User License Agreement Regulatory Information Page About this Guide Documentation ConventionsRelated Following Documentation documentation Product Registration Support Introduction 802.11a 802.11g Network ConfigurationNetwork Configuration and Planning Planning Example ConfigurationsWireless Infrastructure Network Workgroup Ad-Hoc Network Unpacking Bridge Bridge Deciding Where to Place the Bridge Wall-Mounting the Bridge Routing Cable Under the Cradle Securing the Locking Bar Connecting Connecting the Power About the Client List Connecting to a Hub Connecting the Bridge Network printers in areas that are not wired for Ethernet Indicators LED External Antenna Need to ConfigureAttaching An Determining if you Determining if you Need to Configure the Bridge Networks without a Dhcp Server Bridge Default Settings To Wireless Client Infrastructure Using the 3Com Installation CD Using the 3Com Installation CD Installing the Bridge Configuring the Bridge Infrastructure Using the 3ComWireless Device Manager Click Configure Using the 3Com Wireless Infrastructure Device Manager Button Description Management UsingSystem Clearing Applying System Configuration Settings Moving to a new configuration System Properties Server, select Obtain an IP address automatically and click Apply Select Wireless Client Infrastructure to associate with an Select 802.11a to set the Bridge to operate with either Service Area Select Specify the Wireless LAN Service Area to allow External and one internal antenna this setting Being used, click Long Wi-Fi Interoperable Set the Data Preamble No Security Open System 40/64-bit Shared Key WEP 104/128-bit Shared Key 128/152-bit Shared Key Or Disable AES Secondary Radius Using the Configuration Management System Configuring Operation Mode About Uart Configuring Uart Settings Configuring Network Serial Port Settings Applying Settings Reset Under Tools, click Restore Factory Defaults Or with the Bridge out of the cradle Using FTP default Using Tftp Using Http Under Tools, click Backup Wireless Workgroup Bridge Under Tools, click Restore Wireless Workgroup Bridge Summary Page Problems Diagnosing Troubleshooting Uninstall 3Com Wireless Infrastructure Device Manager DisconnectingUninstalling Disconnecting the Bridge Upgrading Bridge Firmware Register Your Service BenefitsSolve Problems Product to Gain Access Software WarrantyProfessional Services Purchase Extended Directory of 3Com resources by region at Contact Us Latin America Telephone Technical Support and Repair END User License Agreement Page Regulatory Information MANUFACTURER’S Declaration of Conformity Industry Canada IC Emissions Compliance Statement Europe EU Declaration of Conformity Bipt Indoor/Outdoor