Configuring Uart Settings | 3Com WL-560 specification

Using the Configuration Management System 41

Configuring UART Settings

For proper operation, it is imperative that these settings always match the settings of the device to which the bridge is connected via the RS-232 port. There are two groups of parameters that need to be configured to accomplish this task: UART Settings and Flow Control Settings.

Flow control is the process of adjusting the flow of data from one device to another to ensure that the receiving device can handle all of the incoming data.

To configure the UART settings:

1Select the baud rate of your device.

The baud rate indicates the data transfer rate of the serial port.

2Determine the data bits setting of the device you are connecting to the

Bridge, then set the Data Bits setting for the bridge that matches the data bits setting of that device.

The Data Bits setting determines the number of bits used to transmit data. The possible values are 7 and 8.

3Determine the stop bits setting of the device you are connecting to the

Bridge, then set the Stop Bits setting on the Bridge that matches the stop bits setting of that device.

The Stop Bits setting determines the number of bits used to represent an end of a character. The value can be 1 or 2.

4Determine the parity bit setting of the device you are connecting to the

Bridge, then set the Parity Bit setting on the Bridge that matches the parity bit setting of that device.

The Parity Bit setting is used to check for correct data transmission.

Options are: none, even, and odd.

Configuring Network Serial Port Settings

For Server Mode, click Server Mode and enter the port number to which the Bridge connects in the List on port field. The default port number is 4000.

For Client Mode, select Client Mode and enter the IP address and port number to which the Bridge connects. The default port number is 4000.

Image 47

3Com WL-560 manual Configuring Uart Settings, Configuring Network Serial Port Settings

Contents

3Com 11a/b/g Wireless Workgroup Bridge User Guide 3Com Corporation Campus Drive Marlborough MA USA Contents Configuring the Bridge END User License Agreement Regulatory Information Page About this Guide Following ConventionsRelated Documentation Documentation documentation Product Registration Support Introduction 802.11g 802.11a Planning ConfigurationNetwork Configuration and Planning Network Workgroup Ad-Hoc Network ConfigurationsWireless Infrastructure Network Example Bridge Unpacking Bridge Wall-Mounting the Bridge Deciding Where to Place the Bridge Routing Cable Under the Cradle Securing the Locking Bar Connecting the Power Connecting Connecting the Bridge About the Client List Connecting to a Hub Network printers in areas that are not wired for Ethernet LED Indicators Determining if you Need to ConfigureAttaching An External Antenna Networks without a Dhcp Server Determining if you Need to Configure the Bridge To Wireless Client Infrastructure Bridge Default Settings Using the 3Com Installation CD Using the 3Com Installation CD Installing the Bridge Configuring the Bridge Device Manager Using the 3ComWireless Infrastructure Using the 3Com Wireless Infrastructure Device Manager Click Configure Button Description System UsingManagement Moving to a new configuration Clearing Applying System Configuration Settings System Properties Apply Server, select Obtain an IP address automatically and click Select 802.11a to set the Bridge to operate with either Select Wireless Client Infrastructure to associate with an Select Specify the Wireless LAN Service Area to allow Service Area Being used, click Long Wi-Fi Interoperable External and one internal antenna this setting Set the Data Preamble 40/64-bit Shared Key WEP No Security Open System 128/152-bit Shared Key 104/128-bit Shared Key AES Or Disable Secondary Radius Using the Configuration Management System About Uart Configuring Operation Mode Configuring Network Serial Port Settings Configuring Uart Settings Reset Applying Settings Or with the Bridge out of the cradle Under Tools, click Restore Factory Defaults Using Tftp Using FTP default Under Tools, click Backup Wireless Workgroup Bridge Using Http Under Tools, click Restore Wireless Workgroup Bridge Summary Page Diagnosing Problems Troubleshooting Disconnecting the Bridge DisconnectingUninstalling Uninstall 3Com Wireless Infrastructure Device Manager Firmware Upgrading Bridge Product to Gain Service BenefitsSolve Problems Register Your Purchase Extended WarrantyProfessional Services Access Software Contact Us Directory of 3Com resources by region at Latin America Telephone Technical Support and Repair END User License Agreement Page Regulatory Information MANUFACTURER’S Declaration of Conformity Industry Canada IC Emissions Compliance Statement Europe EU Declaration of Conformity Bipt Indoor/Outdoor