AEG 8000012364 BAL guide

"UniVert 2" inverter

Type E-number

E230 E230/115/2-VFp26,5-8

3000000646

Rated output capacity	26.5 kVA

Power loss	< 200 W

AC rated input voltage	230 V

AC rated input frequency	50 Hz

Monitoring systems

AC mains undervoltage,	Fault < 90% nominal (207 V), without delay
blocking of the SBS	Acknowledgement > 90% nominal (211 V)
	Acknowledgement > 90% nominal (211 V)

AC mains overvoltage,	Fault > 110% nominal (253 V), without delay
blocking of the SBS	Acknowledgement < 110% nominal (248 V)
	Acknowledgement < 110% nominal (248 V)

AC load undervoltage,	Fault < 88% nominal (202 V), without delay
switchover to mains	Acknowledgement > 88% nominal (207 V)

AC load overvoltage, switchover	Fault > 112% nominal (258 V), without delay
to mains	Acknowledgement < 112% nominal (253 V)
	Acknowledgement < 112% nominal (253 V)

Overtemperature, message	Fault > 80°C, acknowledgement < 70°C, 4 s delay
	self-acknowledging

Synchronism	Fault phase deviation > 3° el., without delay
INV / SBS circuit	Acknowledgement phase deviation < 2.9° el., 2 s delay

Page 39 of 42

8000012364 BAL, en

Image 39

AEG 8000012364 BAL operating instructions Type E-number E230 E230/115/2-VFp26,5-8 3000000646

Contents

Operating Instructions UniVert 2 inverter and SBS option Handling WarrantyDuty to Provide Information Validity Abbreviations HotlineCopyright Table of Contents Maintenance Troubleshooting Technical DataDimensional Drawing Safety Instructions Important Instructions and ExplanationsAccident Prevention Regulations Qualified Personnel Application Safety Awareness Directives Liability System Description General Information Individual or parallel operation with SBS Function of the SystemIndividual INV operation Parallel INV operation Parallel INV operation Description of the INV Block diagram of the inverter Principle of Operation of the INV, Electrical SBS Description of the SBS Principle of Operation of the SBS, Electrical Function of the Inverter S2.1 S2.2 S2.3 ON/OFF SwitchDIL Switch Can Bus Interfaces X6 S2.4 S2.5 S2.6 Address Switches S2.4, S2.5 and S2.6 Own Address INVSwitches S2.7 and S2.8 Number of redundant INVs INVs Settings must be the same on all INVs and the SBS Display Colour Operating status Signalling, Displays and Remote Signals Switchback Attempts Function of the SBS optionalOperating Statuses AC Mains Monitoring System Reset ButtonAC Mains Input AC Busbar S3.1 S3.2 S3.3 S3.7 S3.8 INVs Assignment of the signal terminals Switchover without gapOperating modes Switchover with gap Connection InstallationConnecting the Loads / DC / Mains Start-Up Disconnection Maintenance Troubleshooting Output Voltage DeviationFor systems with SBS additionally General Data INV Technical Data Operation FaultOvertemperature ϑ Collective fault General Data SBS With safe isolation at UO ≤ 60 V DC UniVert 2 inverter Electrical Data At 24 Type E-number G110 E230/10,9/2rfg-CFp2,5 3000000263 Type E-number E230 E230/115/2-VFp26,5-8 3000000646 Inverter dimensions type 1.5 and 3.3 kVA Dimensional Drawing Inverter dimensions type 2.5 kVA SBS dimensions