Manuals / Agilent Technologies / Power Tools / Welding System

Agilent Technologies 5745A, 5752A, 5744A Using the Setup Utility, Factory-shipped LAN Settings

Models: 5751A 5744A 5743A 5750A 5749A 5752A 5747A 5742A 5748A 5741A 5745A 5746A

1 132

Download 132 pages 2.14 Kb

Page 56

4 Operating the Power Supply Remotely

Factory-shipped LAN Settings

The factory-shipped LAN settings documented in the following table are optimized for connecting your power supply to a site network. They should also work well for other network configurations.

The factory-shipped settings can be restored by pressing and holding the front panel LAN button for three seconds. Pressing the LAN button again while the message “LAn rES” is displayed resets the LAN settings.

Factory-shipped non-volatile LAN settings

Get IP Address	Automatic
IP Address	169.254.57.0
Subnet Mask	255.255.0.0
Default Gateway	0.0.0.0
Obtain DNS server from DHCP	Enabled
DNS server	Blank
Host name	A-N57xxA-xxxxx

Dynamic DNS naming service	Enabled
NetBIOS naming service	Enabled
Domain name	Blank
TCP keepalive	Enabled
TCP keepalive seconds	1800
Ethernet Auto-negotiation	Enabled
Ping server	Enabled
Web password	Blank

Using the Setup Utility

A Setup utility that lets you configure the LAN settings of your instrument is provided on the Product Reference CD-ROM included with this manual. Install and run this Setup utility if you cannot configure the LAN interface as previously described in this section.

1Connect your power supply to your computer using either the USB interface or the GPIB interface as previously described.

2Install the Setup utility on your computer. Run the Setup utility by clicking StartProgramsAgilentN5700 Setup Utility.

3Configure the following LAN address parameters. These are located under the Settings tab. For a description of these parameters, refer to the previous section.

56	Series N5700 User’s Guide

Image 56

Agilent Technologies 5745A, 5752A, 5744A, 5743A, 5748A, 5741A, 5746A manual Using the Setup Utility, Factory-shipped LAN Settings

Contents

User’s Guide Legal Notices Agilent Technologies, IncOn supply Off supply Safety NoticesFrame or chassis terminal This Book Contents 113 116118 124Quick Reference System Features Agilent N5700 DC Power Supplies At a GlanceOutput Features Model Voltage Current Range Programmable FunctionsModel Ratings Front Panel At a Glance LAN indicator OCP indicatorLimit indicator Fine indicatorRear Panel At a Glance J2 Sense Connector SW1 Setup SwitchEnable/Disable control Remote sense + Local sense + Not usedJ1 Analog Programming Connector Installation Accessories General InformationModels Items SuppliedInstalling the Unit Safety ConsiderationsInspecting the Unit EnvironmentThan 6 mm into the sides of the unit Rack InstallationCleaning Connecting the Line Cord Power cord, resulting in fireInput Connections for 750W units Input Connections for 1500W unitsInstallation Wire Size TightenedShorted, whichever is greater For 5 a For 10 a For 20A For 50A For 150AOutput voltage of the power supply Load Connections for 6V to 60V ModelsPrevent loosening the connections or bending the bus-bars Cross Section ResistanceWire Size Load Connections for 80V to 600V Models10 mm 0.39 TorqueLoad wires Output Voltage SensingPlug Type Local SensingRemote Sensing Load Considerations Multiple LoadsOutput Noise and Impedance Effects Inductive LoadsParallel Connections Grounding the OutputConnected in parallel Local SensingRemote Sensing Setting up the Master UnitSetting up the Slave Units Setting the Over-Voltage Protection Setting the Over-Current ProtectionSeries Connections Connected in seriesLocal Sensing Remote Sensing Separated and floated from each otherJ1 Connector Connections Voltage of the power supplyMating Plug Extraction toolOperating the Power Supply Locally On check-out procedure Turn-On Check-OutBefore Check-Out Constant Voltage CheckOCP Check UVL CheckConstant Current Check Normal Operation Constant Voltage ModeConstant Current Mode CV/CC Mode Crossover CV/CC SignalOver-Voltage Protection Limit the sink current to less than 10mAUnder-Voltage Limit Over-Current ProtectionOver-Temperature Protection Power-Fail ProtectionFront Panel Lock-Out SYSTCOMMRLST, it cannot be unlocked from the front panelOutput On/Off Controls OUT on buttonSafe-Start and Auto-Restart Output Shut-Off TerminalsSW1 switch ENA+/ENA- pins Output Display Prot Indicator Enable/Disable TerminalsSW1 switch SO Signal Level Output Display Power Supply OK Signal Analog Programming of Output Voltage and CurrentDaisy-Chained Output Shut-down Sense terminal, as it may damage the unitAnalog Programming Control Terminals Voltage Programming of Output Voltage and CurrentSW1 switch Voltage Programming Down defaultResistance Programming of Output Voltage and Current Current ProgrammingDown default J1 pin Voltage Monitor Current Monitor External Monitoring of Output Voltage and CurrentPage Operating the Power Supply Remotely Automation-Ready CD-ROM included with this productAutomation-Ready CD-ROM that is shipped with your product Connecting to the InterfacesGpib Interface Visa address is USB023912055serialnumber0INSTR USB InterfaceLAN Interface Connecting to a Site LAN An example of a hostnameConnecting to a Private LAN Previous settingsCAT5 Crossover Cable InstrumentEthernet Connection Monitoring Using the Web ServerLAN Communication Using Telnet Using SocketsConfiguring the LAN Parameters By the subnet mask setting Factory-shipped non-volatile LAN settings Using the Setup UtilityFactory-shipped LAN Settings Series N5700 User’s Guide Syntax Scpi Commands an IntroductionMultiple Commands in a Message Commands from Different Subsystems Message UnitQueries Common CommandsCommand Terminators Parameter Types Numeric ParametersSuffixes and Multipliers Response Data TypesSubsystem is in the Initiated state Scpi Command CompletionDevice Clear Language Reference Scpi Command Description Scpi Command SummarySubsystem Commands Common Commands Command DescriptionCalibration Commands Commands will generate an errorMeasure Commands CALibrateSTATe Onoff ,password CALibrateSTATe?Output Commands OUTPutSTATe Onoff OUTPutSTATe?Source Commands Model V ratingMin. low limit Max. low limit Status Commands WTG GenerationBit Position Bit Value1024 256 Bit NameSTATusQUEStionableEVENt? 1024 512CLS Bit Position Bit Value 128SRE SRE? ESB = Event status byte summary MAV = Message availableSystem Commands SYSTemCOMMunicateTCPipCONTrol?TST? Trigger Commands ABORtPage Microsoft Excel Microsoft Visual BasicMicrosoft Visual C++ Output Programming Example Series N5700 User’s Guide Trigger Programming Example Series N5700 User’s Guide Page Appendix a Specifications Performance Specifications Agilent Models N5741A N5752A and N5761A N5772ASupplemental Characteristics Programming Resolution Measurement ResolutionRemote Sense Compensation Over-voltage ProtectionSeries and Parallel Capability Savable statesInterface Capabilities Environmental ConditionsOutline Diagram 43.6mmPage Appendix B Verification and Calibration Limits and does not need to be re-calibratedVerification Equipment RequiredPerformance CalibrationPower Supply Measurement TechniquesElectronic Load Current-Monitoring ResistorConstant Voltage Tests Voltage Programming and Readback AccuracyCV Load Effect Model you are checkingCV Source Effect CV NoiseTransient Recovery Time Current Programming and Readback Accuracy CC Load EffectCC Source Effect Test Record Form Agilent N5741A and N5761A Test Record Form Agilent N5742A and N5762A Agilent N5742A and N5762A Report No Date DescriptionTest Record Form Agilent N5743A and N5763A Agilent N5743A and N5763A Report No Date DescriptionTest Record Form Agilent N5744A and N5764A Agilent N5744A and N5764A Report No Date DescriptionTest Record Form Agilent N5745A and N5765A Agilent N5745A and N5765A Report No Date DescriptionTest Record Form Agilent N5746A and N5766A Agilent N5746A and N5766A Report No Date DescriptionTest Record Form Agilent N5747A and N5767A Agilent N5747A and N5767A Report No Date DescriptionTest Record Form Agilent N5748A and N5768A Agilent N5748A and N5768A Report No Date DescriptionTest Record Form Agilent N5749A and N5769A Agilent N5749A and N5769A Report No Date DescriptionTest Record Form Agilent N5750A and N5770A Agilent N5750A and N5770A Report No Date DescriptionUse fixed resistor instead of load modules Test Record Form Agilent N5751A and N5771AAgilent N5751A and N5771A Report No Date Description Test Record Form Agilent N5752A and N5772A Agilent N5752A and N5772A Report No Date DescriptionCalibration Procedure CalibrationVoltage Programming and Measurement Calibration Viattrtmovalue in the ViSetAttribute functionCurrent Programming and Measurement Calibration Appendix C Service Types of Service Available Operating ChecklistTurn-on check out procedure Trouble-shooting guideSymptom Check Does the AC source voltage sag when a load is applied?Error Messages Displaying the Scpi error queueError List ErrorCommand error Syntax errorData type error Command header errorCommand Errors Execution Errors Query ErrorQuery Interrupted Query UnterminatedPage Appendix D Compatibility Result in unpredictable instrument behaviorDifferences In General DifferencesCompatibility Command Compatibility Command SummaryDescription Similar Scpi Command MEASVOLT? Index Initiate commands IndexSpecifications Over-voltage protection130 Series N5700 User’s Guide Safety Manufacturer’sAddress Conforms with the following product standardsManual Updates