Trigsour | Agilent Technologies 6032A, 6035A, 6028A, 6033A, 603xA

Trigger Subsystem

This subsystem controls remote triggering of the power supply.

TRIG[:IMM]

When the trigger subsystem is armed, TRIG generates a trigger signal. The trigger will then:

1.Initiate the output change from the pending level to the immediate level (see CURR[:LEV]:TRIG and VOLT[:LEV]:TRIG).

2.Clear the WTG bit in the Status Operation Condition register.

3.If INIT:CONT has been sent, the trigger subsystem is immediately rearmed for subsequent triggers. This means that as soon as it is cleared, the WTG bit is again set to 1.

Command Syntax	TRIGer[:IMMediate]
Examples	TRIG TRIGGER:IMMEDIATE

TRIG:SOUR

Sets the trigger source to bus commands. Since the power supply has no other trigger source than the GP-IB bus, this command need not be used. It is included in the command set to provide programming compatibility with other instruments (such as the Agilent Electronic Load family) that may have more than one trigger source.

Command Syntax	TRIGer:SOURce BUS
Parameters	<CRD> BUS
*RST Value	BUS
Examples	TRIG: SOUR BUS TRIGGER: SOURCE BUS
Query Syntax	TRIG:SOUR?
Returned Parameters	<CRD> BUS

Voltage Subsystem

This subsystem programs the output voltage of the power supply.

VOLT[:LEV]

Sets the immediate voltage level or the pending triggered voltage level of the power supply. The immediate level is the voltage programmed for the output terminals. The pending triggered voltage level is a stored value that will be transferred to the output when a trigger occurs. If no pending triggered level has been programmed, then the immediate command programs both levels to the same value. Once a triggered level has been programmed, it is unaffected by subsequent changes to the immediate level.

Command Syntax	[SOURce]:VOLTage[:LEVel] [:IMMediate][:AMPLitude] <NRf+>
	[SOURce]:VOLTage[:lEVel]:TRIGgered[:AMPlitude] <Nrf+>
Parameters	See "VSET" in Table 3-7 of Section III.
Default Sufflx	V
Examples	VOLT 200 MV	VOLTAGE:LEVEL 200 MV
	VOLTAGE:LEVEL:IMMEDIATE:AMPLITUDE 2.5
	VOLT:TRIG 20	VOLTAGE:LEVEL:TRIGGERED 20
	VOLTAGE:LEVEL:TRIGGERED:AMPLITUDE 5.5

Standard Commands for Programmable Instruments (SCPI) 103

Image 103

Agilent Technologies 6032A, 6035A, 6028A, 6033A, 603xA, 6023A, 6038A 6010A, 6031A manual Trigsour

Contents

Operating Manual Certification Environmental Conditions Before Applying PowerDo not Service or Adjust Alone General Safety Symbols EMC Declaration Manufacturer’s Declaration Herstellerbescheinigung Table Of Contents Table Of Contents Standard Commands for Programmable Instruments VAC Input Power OptionBlank Front Panel Option Index Description Introduction Accessories Safety ConsiderationsOptions Instrument and Manual Identification Model GP-IB Interconnection Cables and ConnectorsGP-IB Compatibility Ordering Additional Manuals Related Documents SpecificationsIeee 6038A Performance Specifications Agilent Technologies Model 6033A 6035A 6030A6031A 6032A Supplemental Characteristics 6035A 6038A Agilent Model General Information Preparation For Use Initial Inspection Power Connection Input Power RequirementsRack Mounting Power-Cord Plug Configurations Line Voltage Option Conversion Installation Line Voltage Conversion Components Agilent Models 6030A, 6031A, 6032A, 6035A AC Line Impedance CheckRepackaging For Shipment Rear Panel Screw Sizes and Part Numbers Agilent Model 6038A Agilent Model 6033A Operating Instructions Output Range For An Autoranging Power Supply Controls and Indicators Overrange Operation Controls and Indicators Description Number Controls/Indicators Operating Instructions OVP Adjust Turn-On Checkout Procedure Factory Settings, Mode Switch Connecting the Load Initial Setup and Interconnections AWG Maximum Wire Lengths To Limit Voltage DropsCross Section Area Mm2 Kft 10A 17 a Cross Section Area in mm2 Ampacity Stranded Copper Wire Ampacity Wire Size Connecting a Bypass Capacitor Overvoltage Protection OVP Foldback Protection Remote Voltage Sensing Remote Voltage Sensing Mode Switches Voltage Resistance Mode SwitchesMode Switches Programming Mode GP-IB/RPG Protective Circuits Monitor Signals Constant Voltage Operation Local Operation Interface Functions GP-IB OperationConstant Current Operation Return to Local Operating Instructions ERR RDY PON FAU GP-IB Address SelectionRQS Serial Poll Register INH-FLT or RLY LNK Operation Power-On Service RequestInitial Conditions Programming Syntax Output AdjustOVP VMAX? Vmax ? Unmask CC,OR,FOLD Unmask CC, OR, FoldUnmask CC or Fold Vset 5 V VSET5V VMAX? IMAX? VSET? ISET? VOUT? IOUT? OVP? GP-IB Commands Range or **Response To Query Description CommandHOLD? STS? ASTS? TRG SRQ OFF FAULT?UNMASK? SRQ OFF SRQ SRQ on SRQ SRQ? CLR ERR? Vout 15VIOUT 5A Vout 15V Iout 5A TEST? ID? FOLD? HOLD? OUT? SRQ? Format of Numbers Sent from Power SupplySTS? FAULT? ASTS? ERR? UNMASK? TEST? VSET? ISET? DLY? VOUT? IOUT? VMAX? IMAX? Iset Iset 5 a Iset 5 MA VSET? OUT on RST Vmax Imax Vmax 15 Imax 5 a Vmax 15 MV Imax 5 MADLY? OUT ? HOLD? STO Output PS1 Hold ON’’ 5A’’STS? ERR Status Register Bit Position Bit WeightCondition Fold Unmask CC, OR, ERR FaultUnmask TEST? No Errors Error # 10. Status Register Errors Description Analog Programming Resistance Programming of Output Voltage 10. Voltage Programming of Output Voltage Multiple-Supply Operation 12. Resistance Programming of Output Current Series Operation 14. Auto-Parallel Operation 15. Series Operation Fault Input FLT and Remote Inhibit INH Connections 16. FLT/INH Connections 19a. FLT and INH with Multiple Supplies 20. Timing Diagram Page Manual Changes Using Appendix aGeneral Information Description Scope of Appendix a Section lll Manual Changes Section ll Manual ChangesPage Page Introduction Turn-On Check Out ProcedurePossible failure STS Table B-1. ID Query Response Agilent ModelResponse Vset 20 Iset Overvoltage Protection Setting Table B-2. CC Check Command String Agilent ModelString Page Standard Commands for Programmable Instruments Scpi Introduction Linked Connections GP-IB Parameters Common CommandsSubsystem Commands Keywords Figure C-2. Common Command Syntax Diagram PON CME EXE DDE QYE Command SyntaxBit Configuration of Standard Event Status Enable Register Meaning and Type ESR? *PSC *STB? ESE?ESR? OPC? Pending operations are complete when Returned Parameters NR1 Command Syntax PSC bool ParametersDefault Value Example PSC PSC? RST Command Syntax*SAV NRf Parameters Example 1MSS ESB MAV Ques Bit Configuration of Status Byte RegisterSRE? Oper Abor Abort TRGTST? WAI Curr Prot Stat 0 Current Protection State OFF Command Syntax SOURceCURRentPROTectionSTATe bool ParametersCurrlev Currprotstat Outp 1 Output State ON, Norelay Init Initiate ImmediateInitcont 1 Initiatecontinuous Meas CURR? Meas VOLT? Measure Voltage DC? MV OUTPPROTDEL? MIN OUTPPROTDEL? MAX Outpprotdelmin Outputprotdelay MAXOutpprot Outp Prot CLE Output Protection Clear Status Operation Registers Bit Configuration of Operation RegistersSTATOPEREVEN? Status Questionable Registers NTR/PTR CommandsBit Configuration of Questionable Registers Statpres Statquesenab STATQUESCOND?STATQUESEVEN? Systlang Tmsl Systemlanguage Compatibility Syst ERR? System ERROR?Statquesntr 16 Statusquestionableptr STATQUESNTR? STATQUESPTR? Trigsour Volt PROT? Voltage Protection AMPLITUDE? VOLTPROTAMPL?Questionable Status Group Standard Event Status Group Bit SignalStatus Byte and Service Request Enable Registers Questionable Status Group Register PTR NTR Status Byte Register Service Request Enable RegisterStatus Programming Examples ESE SRE Standard Event Status Register Error BitsDevice-Dependent Errors Output Queue Error Number Command Summary Subsystem Commands Scpi Command SummaryInitimm Initcont INITCONT? MEASCURRDC? Common Commands Arps ARPS/SCPI CommandsTable C-6. Comparison of Arps and Scpi Commands Equivalent Scpi CommandPage Output @PS Vset Path NamesInitialization Voltage and Current Programming Output @PSVOUT? Enter @ PSA Voltage and Current Readback END While ERR Fold Output Inhibit / EnablePower Supply Status Present Status Accumulated Status Serial Poll Fault and Mask RegistersOutput @PSUNMASK CC, OR, OV,AC SPOLLRESP= Spoll @PS RQS ERR RDY PON FAU Output @PSSRQ on Output @PS~SRQ OFF Service Request Programming Error Detection Delay TimeOutput @PS ERR? Enter @PSERRCODE OFF KEY Foldback Fault Indicator FLT and Inhibit INHProtection Functions Overvoltage Output @PSSTO 10RCL Hold ModeAdvanced Topics Machines States 210 ! Loop Through the States 10 Times Page Index Atsl Ieee GET OC bit 98, 101 Tmsl SH1 SR1 Asia Pacific United States CanadaEurope Japan Latin America Australia/New Zealand Manual Updates