Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-GS950/8 manual Rebooting the Switch

Models: AT-GS950/8

1 76

Download 76 pages 23.63 Kb

Page 23

Rebooting the Switch

AT-S82 Management Software User’s Guide

Rebooting the Switch

This procedure reboots the switch and reloads the AT-S82 management software from flash memory. You might reboot the device if you believe it is experiencing a problem. Rebooting the device does not change any of the device’s parameter settings.

Caution

The switch does not forward network traffic during the reboot process. Some network traffic may be lost.

To reboot the switch, perform the following procedure:

1.From the main menu, select Reboot. The Reboot page is shown in Figure 6.

Figure 6. Reboot Page

2.Click Reboot.

The switch immediately begins to reload the AT-S82 management software. This process takes approximately one minute to complete. You can not manage the device during the reboot. After the reboot is finished, you can log in again if you want to continue to manage the switch.

23

Image 23

Allied Telesis AT-GS950/8 manual Rebooting the Switch

Contents

AT-S82 For the AT-GS950/8 Layer 2 Gigabit Ethernet WebSmart Switch VersionManagement Software User’s GuideCopyright 2007 Allied Telesis, Inc Contents Tagged Port Members Figures Figures ˆ “Contacting Allied Telesis” on page Prefaceˆ “Where to Find Web-based Guides” on page This preface contains the following sectionsPreface Where to Find Web-based GuidesProducts Sales or Corporate Information Online Support Email and Telephone Support Warranty ReturningManagement Software Updates Contacting Allied TelesisPreface Chapter Getting StartedStarting a Management Session AT-S82 Management Software User’s Guide Figure 2. Main PageSaving Changes To quit a management session, close the web browser Quitting a Management SessionChapter 1 Getting Started Chapter Basic Switch ParametersTo set the switch’s IP configuration, perform the following procedure a. In the IP Address field, enter the IP address. The default is Disabling or Enabling Ping Blocking EnabledDisabled Disabled Enabling or Disabling 802.1X Forwarding ControlEnabled Changing the Administrator’s Password Rebooting the Switch Resetting the Switch and Retaining the IP Address Figure 8. Reset System Page 2. Click Apply Downloading New Firmware This chapter contains the following section Port Configurationˆ “Configuring Port Parameters” on page ChapterConfiguring Port Parameters 3. From the State list, choose one of the following EnabledDisabled Disabled CopperFiber EnabledChapter TrunkingTrunking Guidelines Trunking Algorithm Trunking OverviewAT-S82 Management Software User’s Guide distribution methods ˆ MAC-SA - source MAC addressˆ MAC-DA - destination MAC address ˆ DAxorSA - destination MAC address/source MAC addressDAxorSA Configuring the Trunking AlgorithmMAC-SA MAC-DASetting up the Trunk 5. Click Apply to implement your changes Chapter Port MirroringPort Mirroring Overview Configuring Port Mirroring Chapter 5 Port Mirroring Chapter VLANsIncreased Performance Improved Manageability Increased Security VLAN FeaturesAT-S82 Management Software User’s Guide VLAN Identifier VLAN Port Members VLAN OverviewIncoming Frames Incoming and Outgoing Tagged and Untagged FramesTagged Port Members Untagged Port MembersGuidelines for Creating a VLAN Working with VLANs 2. Click Show All Static VLAN Entries Displaying all VLANsModifying a VLAN Deleting a VLAN Protected Ports VLAN AT-S82 Management Software User’s Guide Figure 21. Protected Port Page2. Determine which ports will be the Primary ports The box for the Primary ports should be empty 4. Click ApplyChapter 6 VLANs Chapter Class of ServiceMapping Ports to Egress Queues Class of Service OverviewPort Priority Queue IEEE 802.1p Priority Levelexample Port Egress QueueMaximum Number of PacketsMapping Priorities to Queues Setting Up the Schedule Assigning Priority to Ports Chapter 7 Class of Service Chapter Spanning Tree Protocol STPBridge Priority and the Root Bridge Spanning Tree OverviewPriority Path Costs and Port CostsIncrement BridgePort Cost Port SpeedPort Cost Port SpeedPort Speed Forwarding Delay and Topology ChangesPort Priority PortHello Time and Bridge Protocol Data Units BPDUs Point-to-Point and Edge Ports Figure 26. Edge Port Spanning Tree and VLANs Chapter 8 Spanning Tree Protocol STP Configuring Spanning Tree Enabled RSTPSTP Compatible When you select a value for maximum age, observe the following rulesDisabled Disabled Configuring STP Port SettingsEnabled False FalseTrue AutoChapter 8 Spanning Tree Protocol STP