Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-GS950/8 To set the switch’s IP configuration, perform the following procedure

Models: AT-GS950/8

1 76

Download 76 pages 23.63 Kb

Page 18

To set the switch’s IP configuration, perform the following procedure:

Chapter 2: Basic Switch Parameters

Configuring the IP Address, Subnet Mask, Gateway Address, and BOOTP or DHCP

Caution

Allied Telesis strongly recommends that you record the MAC address of this switch, as shown on the Basic Switch Information Page (Figure 4) before you configure or enable the BOOTP or DHCP options of the Get IP From parameter. After you enable either option, contact your network administrator for the IP address from the BOOTP or DHCP server that corresponds to the switch’s MAC address.

This procedure explains how to assign an IP address, subnet mask, and gateway address to the switch.

To set the switch’s IP configuration, perform the following procedure:

1.From the main menu, select Basic Switch Information. The Basic Switch Information page is shown in Figure 4.

Figure 4. Basic Switch Information Page

2.To set the switch’s IP address, in the Get IP From field, choose one of the following from the list:

Manual - Allows you to enter static IP address information:

18

Image 18

Allied Telesis AT-GS950/8 manual To set the switch’s IP configuration, perform the following procedure

Contents

User’s Guide For the AT-GS950/8 Layer 2 Gigabit Ethernet WebSmart Switch VersionManagement Software AT-S82Copyright 2007 Allied Telesis, Inc Contents Tagged Port Members Figures Figures This preface contains the following sections Prefaceˆ “Where to Find Web-based Guides” on page ˆ “Contacting Allied Telesis” on pageWhere to Find Web-based Guides PrefaceContacting Allied Telesis Online Support Email and Telephone Support Warranty ReturningManagement Software Updates Products Sales or Corporate InformationPreface Getting Started ChapterStarting a Management Session Figure 2. Main Page AT-S82 Management Software User’s GuideSaving Changes Quitting a Management Session To quit a management session, close the web browserChapter 1 Getting Started Basic Switch Parameters ChapterTo set the switch’s IP configuration, perform the following procedure a. In the IP Address field, enter the IP address. The default is Enabled DisabledDisabling or Enabling Ping Blocking Enabling or Disabling 802.1X Forwarding Control EnabledDisabled Changing the Administrator’s Password Rebooting the Switch Resetting the Switch and Retaining the IP Address Figure 8. Reset System Page 2. Click Apply Downloading New Firmware Chapter Port Configurationˆ “Configuring Port Parameters” on page This chapter contains the following sectionConfiguring Port Parameters Enabled Disabled3. From the State list, choose one of the following Enabled CopperFiber DisabledTrunking ChapterTrunking Overview Trunking Guidelines Trunking Algorithmˆ DAxorSA - destination MAC address/source MAC address distribution methods ˆ MAC-SA - source MAC addressˆ MAC-DA - destination MAC address AT-S82 Management Software User’s GuideMAC-DA Configuring the Trunking AlgorithmMAC-SA DAxorSASetting up the Trunk 5. Click Apply to implement your changes Port Mirroring ChapterPort Mirroring Overview Configuring Port Mirroring Chapter 5 Port Mirroring VLANs ChapterVLAN Features Increased Performance Improved Manageability Increased SecurityAT-S82 Management Software User’s Guide VLAN Overview VLAN Identifier VLAN Port MembersUntagged Port Members Incoming and Outgoing Tagged and Untagged FramesTagged Port Members Incoming FramesGuidelines for Creating a VLAN Working with VLANs Displaying all VLANs 2. Click Show All Static VLAN EntriesModifying a VLAN Deleting a VLAN Protected Ports VLAN The box for the Primary ports should be empty 4. Click Apply Figure 21. Protected Port Page2. Determine which ports will be the Primary ports AT-S82 Management Software User’s GuideChapter 6 VLANs Class of Service ChapterClass of Service Overview Mapping Ports to Egress QueuesIEEE 802.1p Priority Level Port Priority QueuePackets Port Egress QueueMaximum Number of exampleMapping Priorities to Queues Setting Up the Schedule Assigning Priority to Ports Chapter 7 Class of Service Spanning Tree Protocol STP ChapterSpanning Tree Overview Bridge Priority and the Root BridgeBridge Path Costs and Port CostsIncrement PriorityPort Speed Port SpeedPort Cost Port CostPort Forwarding Delay and Topology ChangesPort Priority Port SpeedHello Time and Bridge Protocol Data Units BPDUs Point-to-Point and Edge Ports Figure 26. Edge Port Spanning Tree and VLANs Chapter 8 Spanning Tree Protocol STP Configuring Spanning Tree When you select a value for maximum age, observe the following rules RSTPSTP Compatible EnabledDisabled Configuring STP Port Settings EnabledDisabled Auto FalseTrue FalseChapter 8 Spanning Tree Protocol STP