Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis x600-24Ts-POE manual Reviewing Safety Precautions

Models: x600-24Ts-POE

1 110

Download 110 pages 37.26 Kb

Page 64

Reviewing Safety Precautions

Chapter 3: Installing the Hardware

Reviewing Safety Precautions

Please review the following safety precautions before you begin to install the switches or any of their components.

Note

The indicates that a translation of the safety statement is available in a PDF document titled “Translated Safety Statements” (613-000990) posted on the Allied Telesis website at www.alliedtelesis.com.

Warning: Class 1 Laser product. L1

Warning: Do not stare into the laser beam. L2

Warning: To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician. To avoid the possibility of electric shock, disconnect electric power to the product before connecting or disconnecting the LAN cables. E1

Warning: Do not work on equipment or cables during periods of lightning activity. E2

Warning: Power cord is used as a disconnection device. To de- energize equipment, disconnect the power cord. E3

Warning: Class I Equipment. This equipment must be earthed. The power plug must be connected to a properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts. E4

Pluggable Equipment. The socket outlet shall be installed near the equipment and shall be easily accessible. E5

Caution: Air vents must not be blocked and must have free access to the room ambient air for cooling. E6

Warning: Operating Temperature. This product is designed for a maximum ambient temperature of 40° degrees C. E7

64

Image 64

Allied Telesis x600-24Ts-POE manual Reviewing Safety Precautions

Contents

x600 Series Layer 3 Gigabit Ethernet Switches Installation Guidex600-24Ts x600-24Ts/XP x600-48Ts x600-48Ts/XP x600-24Ts-POE Copyright 2009 Allied Telesis, Inc Electrical Safety and Emissions Standards Translated Safety Statements Contents 10/100/1000Contents x600 Series Layer 3 Gigabit Ethernet Switches Installation Guide 17-pin Connector Pinouts21-pin D-combo Port and Connector Pinouts RJ-45 Style Serial Terminal Port PinoutsContents List of Figures Figures List of Tables Tables Preface ˆ “Safety Symbols Used in this Document” on pageˆ “Where to Find Web-based Guides” on page ˆ “Product Documentation” on pageˆ Virtual Chassis Stacking VCS How To Note ˆ AT-StackXG Stacking Module Installation GuideProduct Documentation ˆ AlliedWare Plus Operating System Software Reference GuideStarting a Management Session x600 Layer 3 Gigabit Ethernet Switch Installation GuideSafety Symbols Used in this Document SymbolMeaning DescriptionWhere to Find Web-based Guides x600 Layer 3 Gigabit Ethernet Switch Installation GuideOnline Support Email and Telephone Support Warranty Returning Management Software UpdatesContacting Allied Telesis Products Sales or Corporate InformationOverview ChapterIntroduction Switch Descriptions Figure 1. x600-24Ts Switchx600-24Ts/XP Switch Figure 2. x600-24Ts/XP SwitchConnector AC Power100-240VAC~ RPS INPUT x600-48Ts/XP Switch Figure 4. x600-48Ts/XP SwitchTransceiver Figure 5. x600-24Ts-POE SwitchConsole Connector Type Speed Duplex Mode Maximum Distance 10/100/1000Base-T PortsCable Type Auto-MDI/ MDI-X Port Pinouts SFP Transceiver Slots XFP Transceiver Slots Models Combo PortsPorts and Slots SD Card Slot AlliedWare Plus Operating System Software Reference GuidePort LEDs 10/100/1000 Base-T LEDsState FunctionDescription LINK/ACT LEDs 2. The PoE LED is only present on the x600-24Ts-POE switchFunction StateXFP Transceiver Slot LEDs FunctionState DescriptionSystem STATUS LEDs FAULT MASTER RPS RESET PWRState DescriptionSTACK LEDs State DescriptionSecure Digital SD LED FunctionState DescriptionTerminal Port Power Over Ethernet Maximum Power ClassMaximum Power Usage6. A legacy device is a node that was manufactured before the IEEE 802.3af standard was completed and may not be compliant. If the device does not conform to the standard, a cross-over cable may be required to insure that the correct DC polarity is supplied to the device Redundant Power Supplies AT-LBM Loop Back Module VCS Stacking Module AC Power Connector Chapter 1 Overview Virtual Chassis Stacking ChapterFeatures of VCStacking The Physical Stack VCStackTM IntroductionVCS Stacking Modules, Cables, and Connections Ring Configuration VCStack Recovery StatesResiliency Link Stack Resiliency Link Event on Master Node Reaction onReaction on Stack With Resiliency LinkResiliency Link Configurations via Switch Ports Figure 25. Resiliency link connecting to switch ports over theFigure 26. Resiliency link connecting to switch ports over the ResiliencyLink VLAN using a network hubResilient Stacked Topology The Role of the Stack Master Stack FormationSelecting the Stack Master Common Stack Configuration Stack Management VLANStack Member Identification DescriptionStack Member Failure and Recovery Running QoS within a VCS stackManagement IP Addresses Description ContinuedVCS Failure Recovery Fallback ActionRe-elect New Stack Master Recombining Separated StacksStack Maintenance Repairing a Broken StubAdding a Stack Member Replacing a Stack MemberChapter 2 Virtual Chassis Stacking Installing the Hardware ˆ “Reviewing Safety Precautions” on pageˆ “Unpacking a Switch” on page ˆ “Installing the Power Cord Retaining Clip” on pageReviewing Safety Precautions All Countries Install product in accordance with local and National Electrical Codes. E8 Caution The unit does not contain field serviceable components. Please return damaged units for servicing Unpacking a Switch Installing the Power Cord Retaining Clip Installing the Switches in an Equipment Rack Figure 32. Mounting the Switch in a Rack Resetting the Switch VC Stacking Module Installation Installing the AT-StackXG Module Figure 36. Installing the AT-StackXG Stacking Module 5.3.1 Software Reference Figure 38. Removing the Plastic ProtectorChapter 3 Installing the Hardware Cabling the Network Ports x600 switch. The chapter contains the following sectionsˆ “Twisted Pair and Fiber Optic Specifications” on page ˆ “Installing SFP/XFP Transceivers” on pageTwisted Pair and Fiber Optic Specifications Twisted Pair Cable SpecificationsMaximum SpeedSFP/XFP Transceiver Specifications x600 Layer 3 Gigabit Ethernet Switch Installation GuideInstalling SFP/XFP Transceivers Installing an SFP TransceiverPage x600-4 Installing an XFP Transceiver 5. Repeat this procedure to install a second XFP transceiver or go to “Cabling the 10/100/1000Base-T and Fiber Optic Ports” on page Cabling the 10/100/1000Base-T and Fiber Optic Ports Powering on a Switch Starting a Local Management Session 3. Configure the terminal or terminal emulation program as follows ˆ Baud rate Default is 9600 bps Range is 9600 to 115200 bpsˆ Data bits ˆ Parity None ˆ Stop bits ˆ Flow control None Chapter 4 Cabling the Network PortsWarranty Registration x600 Layer 3 Gigabit Ethernet Switch Installation GuideChapter 4 Cabling the Network Ports Troubleshooting ChapterPower LED is Off Twisted Pair Port Link LED is Off SFP or XFP LED is Off Chapter 5 TroubleshootingTransceiver is Installed but the Status is “Not Present” System Fault LED is Blinking System Fault LED is Steadily On Cannot Establish a Local Out-of-Band Management Session Switch Functions Intermittently Issues with Virtual Stacking Chassis Configuration Chapter 5 TroubleshootingTechnical Specifications Physical SpecificationsEnvironmental Specifications Appendix AAppendix A Technical Specifications Maximum Operating Altitude3,048 m 10,000 ft Maximum Nonoperating AltitudePower Specifications CertificationsRJ-45 Twisted Pair Port Pinouts SignalSignal Pinout PairRJ-45 Style Serial Terminal Port Pinouts AT-RPS3104 17-pin Connector PinoutsSignal Definition AT-RPS3204 21-pin D-combo Port and Connector Pinouts DefinitionDefinition Appendix A Technical Specifications